- Ruhr-Universität Bochum

The determination of catalyst nanostructures with first-principles accuracy using genetic algorithms (GA) is very demanding due to the cubic scaling of the computational cost of density functional theory (DFT) calculations. Here, we demonstrate, for the case of Ziegler-Natta MgCl2/TiCl4nanoplates, how this structure determination can be accelerated by employing a high-dimensional neural network potential (HDNNP) of essentially DFT accuracy. First, when building HDNNPs for MgCl2/TiCl4clusters with computationally tractable sizes, we found that the structural diversity in the training set is crucial for obtaining HDNNPs reliably describing the large variety of structures generated by GA. The resulting HDNNPs dramatically accelerated the structure determination while yielding results consistent with DFT. Subsequently, we developed a multistep adaptive procedure to construct a HDNNP for MgCl2/TiCl4clusters consistent in size and TiCl4coverage with experiments where prior DFT results were scarcely collected. The structure determination and analyses underline the importance of system size and composition in order to predict some experimentally known facts such as the surface morphology and population of isospecific sites. © 2023 American Chemical Society.

The number of active sites and their intrinsic activity are key factors in designing high-performance catalysts for the oxygen evolution reaction (OER). The synthesis, properties, and in-depth characterization of a homogeneous CoNiFeCu catalyst are reported, demonstrating that multimetal synergistic effects improve the OER kinetics and the intrinsic activity. In situ carbon corrosion and Cu leaching during the OER lead to an enhanced electrochemically active surface area, providing favorable conditions for improved electronic interaction between the constituent metals. After activation, the catalyst exhibits excellent activity with a low overpotential of 291.5 ± 0.5 mV at 10 mA cm−2 and a Tafel slope of 43.9 mV dec−1. It shows superior stability compared to RuO2 in 1 m KOH, which is even preserved for 120 h at 500 mA cm−2 in 7 m KOH at 50 °C. Single particles of this CoNiFeCu after their placement on nanoelectrodes combined with identical location transmission electron microscopy before and after applying cyclic voltammetry are investigated. The improved catalytic performance is due to surface carbon corrosion and Cu leaching. The proposed catalyst design strategy combined with the unique single-nanoparticle technique contributes to the development and characterization of high-performance catalysts for electrochemical energy conversion. © 2022 The Authors. Advanced Materials published by Wiley-VCH GmbH

Mechanochemistry has proven to be an excellent green synthesis method for preparing organic, pharmaceutical, and inorganic materials. Mechanocatalysis, inducing a catalytic reaction by mechanical forces, is an emerging field because neither external temperature nor pressure inputs are required. Previous studies reported enhanced catalytic activity during the mechanical treatment of supported gold catalysts for CO oxidation. So far, the processes inside the milling vessel during mechanocatalysis could not be monitored. In this work, the results of high-energy operando X-ray powder diffraction experiments and online gas analysis will be reported. A specific milling setup with a custom-made vessel and gas dosing system was developed. To prove the feasibility of the experimental setup for operando diffraction studies during mechanocatalysis, the CO oxidation with Au@Fe2O3 as a catalyst was selected as a well-known model reaction. The operando studies enabled monitoring morphology changes of the support as well as changes in the crystallite size of the gold catalyst. The change of the crystal size is directly correlated to changes in the active surface area and thus to the CO2 yield. The studies confirm the successful implementation of the operando setup, and its potential to be applied to other catalytic reactions. © 2022 The Authors. ChemCatChem published by Wiley-VCH GmbH.

Creating high surface area nanocatalysts that contain stacking faults is a promising strategy to improve catalytic activity. Stacking faults can tune the reactivity of the active sites, leading to improved catalytic performance. The formation of branched metal nanoparticles with control of the stacking fault density is synthetically challenging. In this work, we demonstrate that varying the branch width by altering the size of the seed that the branch grows off is an effective method to precisely tune the stacking fault density in branched Ni nanoparticles. A high density of stacking faults across the Ni branches was found to lower the energy barrier for Ni2+/Ni3+oxidation and result in enhanced activity for electrocatalytic oxidation of 5-hydroxylmethylfurfural. These results show the ability to synthetically control the stacking fault density in branched nanoparticles as a basis for enhanced catalytic activity. © 2022 American Chemical Society. All rights reserved.

High entropy alloys (HEA) comprise a huge search space for new electrocatalysts. Next to element combinations, the optimization of the chemical composition is essential for tuning HEA to specific catalytic processes. Simulations of electrocatalytic activity can guide experimental efforts. Yet, the currently available underlying model assumptions do not necessarily align with experimental evidence. To study deviations of theoretical models and experimental data requires statistically relevant datasets. Here, a combinatorial strategy for acquiring large experimental datasets of multi-dimensional composition spaces is presented. Ru–Rh–Pd–Ir–Pt is studied as an exemplary, highly relevant HEA system. Systematic comparison with computed electrochemical activity enables the study of deviations from theoretical model assumptions for compositionally complex solid solutions in the experiment. The results suggest that the experimentally obtained distribution of surface atoms deviates from the ideal distribution of atoms in the model. Leveraging both advanced simulation and large experimental data enables the estimation of electrocatalytic activity and solid-solution stability trends in the 5D composition space of the HEA system. A perspective on future directions for the development of active and stable HEA catalysts is outlined. © 2022 The Authors. Advanced Energy Materials published by Wiley-VCH GmbH

Ball milling is growing increasingly important as an alternative synthetic tool to prepare catalytic materials. It was recently observed that supported metal catalysts could be directly obtained upon ball milling from the coarse powders of metal and oxide support. Moreover, when two compatible metal sources are simultaneously subjected to the mechanochemical treatment, bimetallic nanoparticles are obtained. A systematic investigation was extended to different metals and supports to understand better the mechanisms involved in the comminution and alloying of metal nanoparticles. Based on this, a model describing the role of metal-support interactions in the synthesis was developed. The findings will be helpful for the future rational design of supported metal catalysts via dry ball milling. © 2022 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH.

The design and application of electrocatalysts based on Earth-abundant transition-metal oxides for biomass valorization remain relatively underexplored. Here, we report a nanocasting route to synthesize mesoporous δ-MnO2 with a high surface area (198 m2/g), high pore volume, and narrow pore size distributions to address this issue. By taking structural advantages of mesoporous oxides, this mesoporous δ-MnO2 is employed as a highly efficient, selective, and robust anode for 5-hydroxymethylfurfural (HMF) electrochemical oxidation to 2,5-furandicarboxylic acid (FDCA) with a high yield (98%) and faradic efficiency (98%) under alkaline conditions. The electrocatalyst is also effective for the more difficult HMF electro-oxidation under acidic conditions, forming both FDCA and maleic acid as value-added products in a potential-dependent manner. Experimental results combined with theoretical calculations provide insights into the reaction kinetics and the reaction pathways of electrochemical HMF oxidation over this advanced electrocatalyst. This work thus showcases the rational design of non-noble metal electrodes for multiple applications, such as oxygen evolution, water electrolysis, and biomass upgrading with high energy efficiency. © 2022 The Authors. Published by American Chemical Society and Division of Chemical Education, Inc.

Single Pt atom catalysts are key targets because a high exposure of Pt substantially enhances electrocatalytic activity. In addition, PtRu alloy nanoparticles are the most active catalysts for the methanol oxidation reaction. To combine the exceptional activity of single Pt atom catalysts with an active Ru support we must overcome the synthetic challenge of forming single Pt atoms on noble metal nanoparticles. Here we demonstrate a process that grows and spreads Pt islands on Ru branched nanoparticles to create single-Pt-atom-on-Ru catalysts. By following the spreading process by in situ TEM, we found that the formation of a stable single atom structure is thermodynamically driven by the formation of strong Pt–Ru bonds and the lowering of the surface energy of the Pt islands. The stability of the single-Pt-atom-on-Ru structure and its resilience to CO poisoning result in a high current density and mass activity for the methanol oxidation reaction over time. [Figure not available: see fulltext.] © 2022, The Author(s), under exclusive licence to Springer Nature Limited.

Direct mechanocatalysis (DM) describes solvent-free catalytic reactions that are initiated by mechanical forces in mechanochemical reactors such as ball mills. The distinctive feature of DM is that the milling materials, e.g. the milling balls themselves are the catalyst of the reaction. In this article we follow the historical evolution of this novel concept and give a guide to this emerging, powerful synthesis tool. Within this perspective we seek to highlight the impact of the relevant milling parameters, the nature of the catalyst and potential additives, the scope of reactions that are currently accessible by this method, and the thus far raised hypotheses on the underlying mechanisms of direct mechanochemical transformations. © The Royal Society of Chemistry.

The molecular Suzuki cross-coupling reaction was conducted mechanochemically, without solvents, ligands, or catalyst powders. Utilizing one catalytically active palladium milling ball, products could be formed in quantitative yield in as little as 30 min. In contrast to previous reports, the adjustment of milling parameters led to the complete elimination of abrasion from the catalyst ball, thus enabling the first reported systematic catalyst analysis. XPS, in situ XRD, and reference experiments provided evidence that the milling ball surface was the location of the catalysis, allowing a mechanism to be proposed. The versatility of the approach was demonstrated by extending the substrate scope to deactivated and even sterically hindered aryl iodides and bromides. © 2022 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH.

Selective photocatalytic oxidation of alcohols into value-added aldehydes or ketones is a promising alternative for alcohol oxidation concerning the mild reaction conditions and the controllable selectivity. To increase the activity, defective Bi2WO6 with abundant oxygen vacancies (OVs) was synthesized via substitution of W by Ta. The resulting Ta-doped Bi2WO6 loaded with Pt nanoparticles as co-catalyst efficiently converted aromatic and aliphatic alcohols into the corresponding carbonyl compounds with high selectivity (>99%) in aqueous solution under visible-light irradiation and anaerobic conditions, with equivalent H2 as a coupled product. The optimal amount of benzyl alcohol converted by the Ta-doped catalyst was two times higher than that of the undoped catalyst. Surface OVs were found to favor the dissociative adsorption of the alcohols and to prolong the life time of the charge carriers. More importantly, isotopic labelling experiments confirmed that over Pt-loaded pristine undoped Bi2WO6, the coupled H2 product results from water reduction, while over Pt-loaded Ta-doped Bi2WO6, the produced H2 originates from benzyl alcohol, implying that benzyl alcohol can be photo-oxidized via a complete dehydrogenation pathway. Thus, enriched surface OVs in photocatalysts can activate α-C-H bonds in alcohols, boosting the photocatalytic oxidation performance. © 2021 Elsevier B.V.

Alkaline anodic oxidation of glycerol suffers from facile C−C bond cleavage, especially when using non-precious metal electrocatalysts, which limits the yield of more valuable C3 oxygenates. Usually, a high C3 selectivity is a tradeoff with conversion for most catalysts. Thus, we used solketal as the reactant, which is acetal-protected glycerol with acetone. CV experiments showed that solketal is oxidized over nickel boride (NixB) at potentials where NiOOH is formed. Electrolysis over NixB in a thin-film spectroelectrochemical flow cell at 1.58 V vs. RHE to avoid pronounced oxygen evolution showed a stable current density of ca. 6 mA cm−2. Simultaneously recorded ATR-FTIR spectra revealed solketal conversion to solketalate and formate. Indeed, 59 % conversion and 77 % selectivity to glyceric acid were determined by HPLC after acidic cleavage of the acetal, resulting in a yield of 45 %. Therefore, solketal is a promising reactant for the selective electrosynthesis of glyceric acid. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH.

Although highly desired and studied for decades, direct methane functionalization to liquid products remains a challenge. We report an electrochemical system using a boron-doped diamond (BDD) anode in concentrated sulfuric acid that is able to convert methane to methyl bisulfate and methanesulfonic acid without the use of a catalyst by indirect electrochemical oxidation. Due to its high material stability, BDD can be operated at high current densities. High temperature (140 °C) and pressure (70 bar) support the formation of methyl bisulfate to concentrations as high as 160 mM in 3 h and methanesulfonic acid to concentrations of up to 750 mM in 8 h. We present a novel way of catalyst-free electrochemical methane oxidation and show general trends and limitations of this reaction. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

Electrocatalytic recycling of waste nitrate (NO3−) to valuable ammonia (NH3) at ambient conditions is a green and appealing alternative to the Haber−Bosch process. However, the reaction requires multi-step electron and proton transfer, making it a grand challenge to drive high-rate NH3 synthesis in an energy-efficient way. Herein, we present a design concept of tandem catalysts, which involves coupling intermediate phases of different transition metals, existing at low applied overpotentials, as cooperative active sites that enable cascade NO3−-to-NH3 conversion, in turn avoiding the generally encountered scaling relations. We implement the concept by electrochemical transformation of Cu−Co binary sulfides into potential-dependent core−shell Cu/CuOx and Co/CoO phases. Electrochemical evaluation, kinetic studies, and in−situ Raman spectra reveal that the inner Cu/CuOx phases preferentially catalyze NO3− reduction to NO2−, which is rapidly reduced to NH3 at the nearby Co/CoO shell. This unique tandem catalyst system leads to a NO3−-to-NH3 Faradaic efficiency of 93.3 ± 2.1% in a wide range of NO3− concentrations at pH 13, a high NH3 yield rate of 1.17 mmol cm−2 h−1 in 0.1 M NO3− at −0.175 V vs. RHE, and a half-cell energy efficiency of ~36%, surpassing most previous reports. © 2022, The Author(s).

The reaction pathways of higher alcohol synthesis over a bulk Co−Cu catalyst (Co : Cu=2 : 1) were investigated by applying high-pressure pulse experiments as a surface-sensitive operando method at 280 °C and 60 bar. Using high-pressure CO and H2 pulses in a syngas flow with a H2:CO ratio of 1, it was shown that the surface of the working 2CoCu catalyst is saturated with adsorbed CO, but not with adsorbed atomic hydrogen, because only the H2 pulses increased the yields of all alcohols and alkanes. The reverse water gas shift reaction (WGSR) was investigated by pulsing CO2. The CO2 pulses poisoned the formation of methanol, ethanol, and 1-propanol, and the absence of significant CO and H2O responses indicates that the WGSR is not efficiently catalyzed by the applied 2CoCu catalyst excluding the presence of exposed Cu0 sites. A series of ethylene pulses showed that when a threshold mole fraction of ethylene of about 1 vol % is surpassed, 2CoCu is an active catalyst for the hydroformylation of ethylene to 1-propanol pointing to the presence of highly coordinatively unsaturated Co sites. © 2022 The Authors. ChemCatChem published by Wiley-VCH GmbH.

Nanocatalyst optimisation through electrochemical dealloying has been employed as a successful strategy to increase catalytic activity, while reducing the need for precious metals. We present here a new pathway to influence the electrochemical dealloying, through external homogeneous magnetic fields. A homogeneous magnetic field with a flux density of 450 mT in two orientations, parallel or perpendicular to the current direction, was used during electrochemical dealloying using cyclic voltammetry of AgAu nanoparticles. We found increased porosity for low dealloying cycle numbers and improved catalytic properties after longer cycling, compared to nanoparticles dealloyed in the absence of magnetic fields. These findings demonstrate that magnetic fields applied during electrochemical dealloying have currently untapped potential that can be used to influence material properties in a new way and give researchers another powerful tool for material design. © 2022

Deciphering the influence of nanocatalyst morphology on their catalytic activity in the oxygen evolution reaction (OER), the limiting reaction in water splitting process, is essential to develop highly active precious metal-free catalysts, yet poorly understood. The intrinsic OER activity of Co3O4 nanocubes and spheroids is probed at the single particle level to unravel the correlation between exposed facets, (001) vs. (111), and activity. Single cubes with predominant (001) facets show higher activity than multi-faceted spheroids. Density functional theory calculations of different terminations and reaction sites at (001) and (111) surfaces confirm the higher activity of the former, expressed in lower overpotentials. This is rationalized by a change in the active site from octahedral to tetrahedral Co and the potential-determining step from *OH to *O for the cases with lowest overpotentials at the (001) and (111) surfaces, respectively. This approach enables the identification of highly active facets to guide shape-selective syntheses of improved metal oxide nanocatalysts for water oxidation. © 2022 The Authors. Advanced Functional Materials published by Wiley-VCH GmbH.

Fuel cells recombine water from H2 and O2 thereby can power, for example, cars or houses with no direct carbon emission. In anion-exchange membrane fuel cells (AEMFCs), to reach high power densities, operating at high pH is an alternative to using large volumes of noble metals catalysts at the cathode, where the oxygen-reduction reaction occurs. However, the sluggish kinetics of the hydrogen-oxidation reaction (HOR) hinders upscaling despite promising catalysts. Here, the authors observe an unexpected ingress of B into Pd nanocatalysts synthesized by wet-chemistry, gaining control over this B-doping, and report on its influence on the HOR activity in alkaline conditions. They rationalize their findings using ab initio calculations of both H- and OH-adsorption on B-doped Pd. Using this “impurity engineering” approach, they thus design Pt-free catalysts as required in electrochemical energy conversion devices, for example, next generations of AEMFCs, that satisfy the economic and environmental constraints, that is, reasonable operating costs and long-term stability, to enable the “hydrogen economy.”. © 2022 The Authors. Advanced Materials published by Wiley-VCH GmbH.

Electrocatalytic oxidation of glycerol (GOR) as the anode reaction in water electrolysis facilitates the production of hydrogen at the cathode at a substantially lower cell voltage compared with the oxygen evolution reaction. It simultaneously provides the basis for the production of value-added compounds at the anode. We investigate earth-abundant transition-metal oxide nanoparticles (Fe, Ni, Mn, Co) embedded in multiwalled carbon nanotubes as GOR catalysts. Out of the four investigated composites, the Ni-based catalyst exhibits the highest catalytic activity toward the GOR according to rotating disk electrode voltammetry, reaching a current density of 10 mA cm–2 already at 1.31 V vs RHE, a potential below the formation of Ni3+. Chronoamperometry conducted in a flow-through cell followed by HPLC analysis is used to identify and quantify the GOR products over time, revealing that the applied potential, electrolyte concentration, and duration of the experiment impact strongly the composition of the products’ mixture. Upon optimization, the GOR is directed toward oxalate production. Moreover, oxalate is not further converted and hence accumulates as a major organic product under the chosen conditions in a concentration ratio of 60:1 with acetate as a minor product after 48 h electrolysis in 7 M KOH, which represents a promising route for the synthesis of this highly valued product. © 2022 American Chemical Society

The development of noble-metal-free electrocatalysts is regarded as a key factor for realizing industrial-scale hydrogen production powered by renewable energy sources. Inspired by nature, which uses Fe-and Ni-containing enzymes for efficient hydrogen generation, Fe/Ni-containing chalcogenides, such as oxides and sulfides, received increasing attention as promising electrocatalysts to produce hydrogen. We herein present a novel synthetic procedure for mixed Fe/Ni (oxy)sulfide materials by the controlled (partial) sulfidation of NiFe2O4 (NFO) nanoparticles in H2S-containing atmospheres. The variation in H2S concentration and the temperature allows for a precise control of stoichiometry and phase composition. The obtained sulfidized materials (NFS) catalyze the hydrogen evolution reaction (HER) with increased activity in comparison to NFO, up to −10 and −100 mA cm−2 at an overpotential of approx. 250 and 450 mV, respectively. © 2022 by the authors. Licensee MDPI, Basel, Switzerland.

Trihalide salts were found to efficiently promote photochemical dediazotizing halogenations of diazonium salts. In contrast to classical Sandmeyer reactions, no metal catalysts are required to achieve high yields and outstanding selectivities for halogenation over competing hydridodediazotization. Convenient protocols are disclosed for synthetically meaningful brominations, iodinations, and chlorinations of diversely functionalized derivatives. © 2021 The Authors. Chemistry - A European Journal published by Wiley-VCH GmbH

Gas diffusion electrodes (GDE) obtained by sputtering metal films on polytetrafluoroethylene (PTFE) membranes are among the most performant electrodes used to electrochemically reduce CO2. The present work reveals several essential aspects for fabricating performant PTFE-based gas diffusion electrodes (GDEs) for CO2 electroreduction (CO2R). We show that adding an additive layer (a mixture of carbon and Nafion™ or Nafion™ only) is required for stabilizing the metal catalyst film (Cu), deposited via sputtering on the PTFE membrane, during the CO2R experiments. We found that the PTFE membrane thickness used in the GDE fabrication plays an essential role in electrode performance. The quantification of the products formed during the CO2R conducted in a flow-cell electrolyzer revealed that on thinner membranes, CO2R is the dominant process while on thicker ones, the H2 formation is promoted. Thus, the PTFE membrane influences the CO2 transport to the catalyst layer and can be used to promote the CO2R while maintaining a minimum H2 production. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

Mitigating high energy costs related to sustainable H2 production via water electrolysis is important to make this process commercially viable. Possible approaches are the investigation of low-cost, highly active oxygen evolution reaction (OER) catalysts and the exploration of alternative anode reactions, such as the electrocatalytic isopropanol oxidation reaction (iPOR) or the glycerol oxidation reaction (GOR), offering the possibility of simultaneously lowering the anodic overpotential and generating value-added products. A suitable class of catalysts are non-noble metal-based perovskites with the general formula ABO3, featuring rare-earth metal cations at the A- and transition metals at the B-site. We synthesised a series of LaFe1-xCoxO3 materials with x=0–0.70 by automated co-precipitation at constant pH and subsequent calcination at 800 °C. X-ray diffraction studies revealed that the phase purity was preserved in samples with x≤0.3. The activity towards the OER, iPOR, and GOR was investigated by rotating disk electrode voltammetry, showing a relation between structure and metal composition with the activity trends observed for the three reactions. Additionally, GOR product analysis via high-performance liquid chromatography (HPLC) was conducted after 24 and 48 h electrolysis in a circular flow-through cell setup, pointing out a trade-off between activity and selectivity. © 2022 The Authors. ChemElectroChem published by Wiley-VCH GmbH

Bimetallic tandem catalysts have emerged as a promising strategy to locally increase the CO flux during electrochemical CO2 reduction, so as to maximize the rate of conversion to C−C-coupled products. Considering this, a novel Cu/C−Ag nanostructured catalyst has been prepared by a redox replacement process, in which the ratio of the two metals can be tuned by the replacement time. An optimum Cu/Ag composition with similarly sized particles showed the highest CO2 conversion to C2+ products compared to non-Ag-modified gas-diffusion electrodes. Gas chromatography and in-situ Raman measurements in a CO2 gas diffusion cell suggest the formation of top-bound linear adsorbed *CO followed by consumption of CO in the successive cascade steps, as evidenced by the increasingνC−H bands. These findings suggest that two mechanisms operate simultaneously towards the production of HCO2H and C−C-coupled products on the Cu/Ag bimetallic surface. © 2022 The Authors. Chemistry - A European Journal published by Wiley-VCH GmbH.

CO2 methanation using nickel-based catalysts has attracted large interest as a promising power-to-gas route. Ni nanoparticles supported on nitrogen-doped CNTs with Ni loadings in the range from 10 wt% to 50 wt% were synthesized by impregnation, calcination and reduction and characterized by elemental analysis, X-ray powder diffraction, H2 temperature-programmed reduction, CO pulse chemisorption and transmission electron microscopy. The Ni/NCNT catalysts were highly active in CO2 methanation at atmospheric pressure, reaching over 50% CO2 conversion and over 95% CH4 selectivity at 340 °C and a GHSV of 50,000 mL g−1 h−1 under kinetically controlled conditions. The small Ni particle sizes below 10 nm despite the high Ni loading is ascribed to the efficient anchoring on the N-doped CNTs. The optimum loading of 30 wt%–40 wt% Ni was found to result in the highest Ni surface area, the highest degree of conversion and the highest selectivity to methane. A constant TOF of 0.3 s−1 was obtained indicating similar catalytic properties of the Ni nanoparticles in the range from 10 wt% to 50 wt% Ni loading. Long-term experiments showed that the Ni/NCNT catalyst with 30 wt% Ni was highly stable for 100 h time on stream. © 2020 Science Press

In this issue of Matter, Yao et al. report on advanced non-equilibrium high-temperature entropy-controlled synthesis of polyelemental nanoparticles. They achieve extreme mixing of 15 metals, some of them previously immiscible, in the form of a single phase solid solution. The compositionally tunable properties of such atomic scale mixtures within a simple crystal structure makes them highly interesting for the design of new materials, e.g., electrocatalysts. © 2021 Elsevier Inc.

Value-added chemicals, fuels, and pharmaceuticals synthesized by organic transformation from raw materials via catalytic techniques have attracted enormous attention in the past few decades. Heterogeneous catalysts with high stability, long cycling life, good environmental-friendliness, and economic efficiency are greatly desired to accomplish the catalytic organic transformations. With the advantages of reversible Ce3+/Ce4+ redox pairs, tailorable oxygen vacancies, and surface acid-base properties, ceria-based catalysts have been actively investigated in the fields of catalytic organic synthesis. In this Review, we summarize the fundamentals and latest applications of ceria-based heterogeneous catalysts for organic transformations via thermocatalytic and photocatalytic routes. The fabricating approaches of various ceria and ceria-based catalysts and their structure/composition-activity relationship are discussed and prospected. The advanced characterization techniques and theoretical methods for reaction mechanism studies over CeO2-based catalysts are summarized and discussed. This comprehensive Review provides a basic understanding of the structure-performance relationships of ceria-based catalysts for organic synthesis. In addition, it also provides some insights and outlooks in the design and research direction in the ceria-based catalysts with better performance. © 2021 American Chemical Society.

The stability of electrocatalysts is of great importance to ensure their applicability, but stability is generally only considered for catalysts polarised to a constant potential or current density. This excludes stability evaluation under start/stop conditions in a fuel cell or in reversible batteries in which the catalyst is alternately polarised to high opposite potentials. For example, the poor cyclability of metal-air batteries is mainly due to the decrease in the oxygen reduction activity of electrocatalysts during the high applied potentials for the oxygen evolution reaction during battery charging. To investigate and at least partially mitigate the loss of electrocatalytic activity for the oxygen reduction reaction, we employed reductive pulses with the aim of restoring the catalytic activity of the active sites for the oxygen reduction reaction. Optimisation of the reductive pulse parameters makes it possible to substantially prolong the oxygen reduction activity of a Fe-Nx-doped carbon-based oxygen reduction electrocatalyst. © 2021 The Author(s)

The influence of the drop-casted nickel boride catalyst loading on glassy carbon electrodes was investigated in a spectroelectrochemical ATR-FTIR thin-film flow cell applied in alkaline glycerol electrooxidation. The continuously operated radial flow cell consisted of a borehole electrode positioned 50 µm above an internal reflection element enabling operando FTIR spectroscopy. It is identified as a suitable tool for facile and reproducible screening of electrocatalysts under well-defined conditions, additionally providing access to the selectivities in complex reaction networks such as glycerol oxidation. The fast product identification by ATR-IR spectroscopy was validated by the more time-consuming quantitative HPLC analysis of the pumped electrolyte. High degrees of glycerol conversion were achieved under the applied laminar flow conditions using 0.1 M glycerol and 1 M KOH in water and a flow rate of 5 µL min−1. Conversion and selectivity were found to depend on the catalyst loading, which determined the catalyst layer thickness and roughness. The highest loading of 210 µg cm−2 resulted in 73% conversion and a higher formate selectivity of almost 80%, which is ascribed to longer residence times in rougher films favoring readsorption and C–C bond scission. The lowest loading of 13 µg cm−2 was sufficient to reach 63% conversion, a lower formate selectivity of 60%, and, correspondingly, higher selectivities of C2 species such as glycolate amounting to 8%. Thus, only low catalyst loadings resulting in very thin films in the few μm thickness range are suitable for reliable catalyst screening. © 2021 Dalian Institute of Chemical Physics, the Chinese Academy of Sciences

The effect of surface orientations on the formation of iridium oxide species during the oxygen evolution reaction (OER) remains yet unknown. Herein, we use a needle-shaped iridium atom probe specimen as a nanosized working electrode to ascertain the role of the surface orientations in the formation of oxide species during OER. At the beginning of electrolysis, the top 2–3 nm of (024), (026), (113), and (115) planes are covered by IrO−OH, which activates all surfaces towards OER. A thick subsurface oxide layer consisting of sub-stoichiometric Ir−O species is formed on the open (024) planes as OER proceeds. Such metastable Ir−O species are thought to provide an additional contribution to the OER activity. Overall, this study sheds light on the importance of the morphological effects of iridium electrocatalysts for OER. It also provides an innovative approach that can directly reveal surface species on electrocatalysts at atomic scale. © 2021 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH

Rational design of highly active electrocatalysts for the oxygen evolution reaction (OER) is critical to improving overall electrochemical water splitting efficiency. This study suggests hollow CeO2@Co2N nanosheets synthesized using Co-ZIF-L as a precursor, followed by a hydrothermal reaction and a nitridation process as very attractive OER catalysts. The increased activity is supposed to be due to nitridation and strong electronic interaction between CeO2 and Co2N that contribute to the formation of active CoOOH phase. The synthesized CeO2@Co2N exhibits low overpotentials of 219 and 345 mV at OER current densities of 10 and 100 mA cm–2, respectively, as well as a long-term durability of 30 h at a comparatively high current density of 100 mA cm−2. © 2021 The Authors. Advanced Materials Interfaces published by Wiley-VCH GmbH

"Why?"is the question that initiates science. "Why?"is also the answer that maintains science. This interrogative adverb fuels the scientific career of Robert Schlögl. Robert is a dedicated solid-state chemist who has found his specialization in untangling the working principles of heterogeneous catalysts under realistic conditions. As such he combines the full complexity of real catalysts with tailor-made operando experiments to overcome pressure, material, and complexity gaps. His ability to quickly abstract the meaning of spectroscopic and microscopic data, his talent to ask the right question paired with curiosity, diligence, and creativity have made him a world-leading expert in heterogeneous catalysis and energy science. His scientific passion is focused on untangling chemical dynamics as well as working principles and understanding the important interplay of geometric and electronic structures in functional materials. Thereby his research interests involve ammonia and methanol synthesis, carbon materials in catalysis, hydrogenation, and dehydrogenation, selective oxidation, and the development of operando setups for microscopy and spectroscopy. He also has a strong commitment to society in scientifically accelerating the energy transition ("Energiewende") in Europe, where he focuses on CO2 utilization and hydrogen as an energy carrier. This is manifested in three recent large Germany-wide projects: Carbon2Chem, CatLab, and TransHyDe. ©

Understanding the structure-property relations of non-precious metal heteroatom co-doped carbon electrocatalysts exhibiting high activity as well as long-term durability for both ORR and OER remains challenging but is indispensable for the development of bifunctional ORR/OER electrocatalysts. We propose B-N-co-doped graphitic 2D carbon nanostructures impregnated with controlled amount of transition metals (M-BCN; M=Co, Ni, Fe, Cu) as bifunctional ORR/OER electrocatalysts. Co-BCN outperformed the Ni-, Fe-, Cu-based BCN catalysts exhibiting potential values of 0.87 V and 1.62 V at −1 mA/cm2 and 10 mA/cm2 during ORR and OER, respectively. Importantly, Co-BCN shows bifunctional cyclic stability (Δη; EOER−EORR=0.75 V) of up to 300 cycles in 1 M KOH for a duration of 20 h with total activity loss of only 10.2 % (ORR) and 6.2 % (OER), respectively. A low loading of the metal precursors was used to preserve porosity and to facilitate the formation of metal nanoparticles or M−NxB/C type species embedded in the graphitic carbon layers. The B-N-co-doped graphitic layers also protect the embedded metal nanoparticles explaining the observed long-term stability. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

Multiple-principal element alloys hold great promise for multifunctional material discovery (e.g., for novel electrocatalysts based on complex solid solutions) in a virtually unlimited compositional space. Here, the phase constitution of the noble metal system Ag-Ir-Pd-Pt-Ru was investigated over a large compositional range in the quinary composition space and for different annealing temperatures from 600 to 900 °C using thin-film materials libraries. Composition-dependent X-ray diffraction mapping of the as-deposited thin-film materials library indicates different phases being present across the composition space (face-centered cubic (fcc), hexagonal close packed (hcp) and mixed fcc + hcp), which are strongly dependent on the Ru content. In general, low Ru contents promote the fcc phase, whereas high Ru contents favor the formation of an hcp solid-solution phase. Furthermore, a temperature-induced phase transformation study was carried out for a selected measurement area of fcc-Ag5Ir8Pd56Pt8Ru23. With increasing temperature, the initial fcc phase transforms to an intermediate C14-type Laves phase at 360 °C, and then to hcp when the temperature reaches 510 °C. The formation and disappearance of the hexagonal Laves phase, which covers a wide temperature range, plays a crucial role of bridging the fcc to hcp phase transition. The obtained composition, phase and temperature data are transformed into phase maps which could be used to guide theoretical studies and lay a basis for tuning the functional properties of these materials. [Figure not available: see fulltext.] © 2021, The Author(s).

In a previous publication, ball milling was introduced as an effective method for the preparation of supported metal catalysts, simply from the coarse powders of the metal and metal oxide support. In this follow-up study, we demonstrate that mixing multiple metal sources can result in supported alloyed nanoparticles, extending the field of application of the method to the synthesis of supported bimetallic catalysts. Ball milling Au and Pd or Au and Cu in a high-energy regime (shaker mill) indeed led to the formation of Au-Pd and Au-Cu nanoparticles, supported on MgO or yttria-stabilized zirconia (YSZ), which were explored as model systems. Powder X-ray diffraction and electron microscopy were the primary means to investigate as-synthesized materials. The catalytic performance in CO oxidation was also investigated to understand better how the synthetic method could affect the features of the final materials as catalysts. © 2021 The Authors. Published by American Chemical Society.

Metal-rich transition metal sulfides recently gained increasing attention as electrocatalysts for the hydrogen evolution reaction (HER), as they are capable to overcome major challenges faced by sulfide-rich metal catalysts such as limited conductivity and the necessity of nanostructuring. Herein, we present the synthesis, characterization and electrocatalytic investigation of ternary metal-rich sulfide composites FexCo9–xS8 as well as NiyCo9–yS8 (x = y = 0–4.5), which possess pentlandite-type structures. In this study, we show a stepwise alteration of the binary cobalt pentlandite Co9S8 and report on the replacement of cobalt with up to 4.5 equivalents of either iron or nickel. These altered pentlandite composites facilitate the proton reduction in acidic media at different temperatures. We furthermore show that the stoichiometric variation has a decisive influence on the electrochemical activation/deactivation behavior of the catalysts under reductive electrocatalytic conditions. Here, Co-deficient composites display an improved HER performance in contrast to Co9S8. Notably, Ni/Co compounds generally tend to show higher catalytic activities towards HER than their respective Fe/Co compounds. © 2021 Dalian Institute of Chemical Physics, the Chinese Academy of Sciences

Ammonia synthesis via the high-temperature and high-pressure Haber-Bosch process is one of the most important chemical processes in the world. In spite of numerous attempts over the last 100 years, continuous Haber-Bosch type ammonia synthesis at room-temperature had not been possible, yet. We report the development of a mechanocatalytic system operating continuously at room-temperature and at pressures down to 1 bar. With optimized experimental conditions, a cesium-promoted iron catalyst was shown to produce ammonia at concentrations of more than 0.2 vol. % for over 50 hours. © 2021 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH

Sintering-induced aggregation of active metals is a major cause of catalyst deactivation. Catalysts that can operate above 800°C are rare. Here, we report an unusual noble metal catalyst with sintering-induced activation at temperatures up to 1,000°C. The catalyst consists of atomically dispersed palladium embedded in a reducible SnO2 support designated for lean methane combustion. High temperature reaction simultaneously causes favorable changes of palladium ensemble state combining synergistically with lattice oxygen activation. Such changes lead to at least one order of magnitude improvement of the intrinsic reactivity, which compensates the surface area loss. Extensive characterizations such as atom probe tomography, X-ray absorption spectroscopy, and isotope tracking together with theoretical calculations illustrate the structure and surface chemistry changes and their impacts on the reaction mechanism. The catalyst also shows notable long-term stability and facile regeneration after poisoning. Our work may provide new insights into designing active and thermally stable catalysts. © 2020 The Author(s) Yang et al. report that atomic Pd catalysts on SnO2 undergo sintering of both Pd and support during high-temperature catalytic oxidation process. The sintered catalyst not only shows significant increase in activity for methane combustion under harsh reaction conditions, but also retains catalytic stability with high-temperature tolerance up to 1,000°C. © 2020 The Author(s)

Complex solid solution (CSS) (often denoted as high-entropy alloy) electrocatalysts enable access to unique possibilities for tailoring active sites while overcoming ever-existing limitations in electrocatalysis by unique interactions of various elements in direct neighborhood. The challenge lies in the development of strategies, which allow for systematic design of element combination and composition optimization in the multinary composition space. This challenge is accompanied by a lack of a suitable analysis method of experimental activity measurements, which can cope with the complex surface structure of this catalyst class. In this work, we propose the advantageous use of inflection points of voltammetric activity curves as activity descriptors enabling to correlate the potential of individual surface site groups to the respective peaks in the adsorption energy distribution pattern. This concept allows to methodologically gather information about the importance of each element in a CSS with respect to activity and stability of the relevant active sites and provides the basis for a guideline for systematic composition optimization. Further, the effect of phase stability on specific surface site groups as induced by degradation of the CSS phase or oxidation can be monitored. These concepts are experimentally evaluated using Cr-Mn-Fe-Co-Ni as a model system. Nanoparticles are synthesized with systematically varied compositions by means of scalable laser ablation synthesis using a multinary target. The composition is optimized with respect to the electrocatalytic activity for the oxygen reduction reaction (ORR) by varying its Mn content via laser ablation synthesis in ethanol. Subsequently, the concept is applied using rotating disk electrodes for ORR analysis in alkaline media. © 2021 American Chemical Society. All rights reserved.

Hydrogen production is a key driver for sustainable and clean fuels used to generate electricity, which can be achieved through electrochemical splitting of water in alkaline solutions. However, the hydrogen evolution reaction (HER) is kinetically sluggish in alkaline media. Therefore, it has become imperative to develop inexpensive and highly efficient electrocatalysts that can replace the existing expensive and scarce noble-metal-based catalysts. Herein, we report on the rational design of nonprecious heterostructured electrocatalysts comprising a highly conductive face-centered cubic nickel metal, a nickel sulfide (NiS) phase, and a reduced graphene oxide (rGO) doped with phosphorous (P), sulfur (S), and nitrogen (N) in one ordered heteromaterial named Ni/NiS/P,N,S-rGO. The Ni/NiS/P,N,S-rGO electrode shows the best performance toward HER in 1.0 M KOH media among all materials tested with an overpotential of 155 mV at 10.0 mA cm-2 and a Tafel slope of 135 mV dec-1. The performance is comparable to the herein used Pt/C-20% benchmark catalyst examined under the same experimental conditions. The chronoamperometry and chronopotentiometry measurements have reflected the high durability of the Ni/NiS/P,N,S-rGO electrode for technological applications. At the same time, the current catalyst showed a high robustness and structure retention after long-term HER performance, which is reflected by SEM, XRD, and XPS measurements. ©

Co3O4 nanocubes are evaluated concerning their intrinsic electrocatalytic activity towards the oxygen evolution reaction (OER) by means of single-entity electrochemistry. Scanning electrochemical cell microscopy (SECCM) provides data on the electrocatalytic OER activity from several individual measurement areas covering one Co3O4 nanocube of a comparatively high number of individual particles with sufficient statistical reproducibility. Single-particle-on-nanoelectrode measurements of Co3O4 nanocubes provide an accelerated stress test at highly alkaline conditions with current densities of up to 5.5 A cm−2, and allows to derive TOF values of up to 2.8×104 s−1 at 1.92 V vs. RHE for surface Co atoms of a single cubic nanoparticle. Obtaining such high current densities combined with identical-location transmission electron microscopy allows monitoring the formation of an oxy(hydroxide) surface layer during electrocatalysis. Combining two independent single-entity electrochemistry techniques provides the basis for elucidating structure–activity relations of single electrocatalyst nanoparticles with well-defined surface structure. © 2021 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH

The formation of a vast number of different multielement active sites in compositionally complex solid solution materials, often more generally termed high-entropy alloys, offers new and unique concepts in catalyst design, which mitigate existing limitations and change the view on structure–activity relations. We discuss these concepts by summarising the currently existing fundamental knowledge and critically assess the chances and limitations of this material class, also highlighting design strategies. A roadmap is proposed, illustrating which of the characteristic concepts could be exploited using which strategy, and which breakthroughs might be possible to guide future research in this highly promising material class for (electro)catalysis. © 2021 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH

By using the crystalline precursor decomposition approach and direct co-precipitation the composition and mesostructure of cobalt-based spinels can be controlled. A systematic substitution of cobalt with redox-active iron and redox-inactive magnesium and aluminum in a cobalt spinel with anisotropic particle morphology with a preferred 111 surface termination is presented, resulting in a substitution series including Co3O4, MgCo2O4, Co2FeO4, Co2AlO4 and CoFe2O4. The role of redox pairs in the spinels is investigated in chemical water oxidation by using ceric ammonium nitrate (CAN test), electrochemical oxygen evolution reaction (OER) and H2O2 decomposition. Studying the effect of dominant surface termination, isotropic Co3O4 and CoFe2O4 catalysts with more or less spherical particles are compared to their anisotropic analogues. For CAN-test and OER, Co3+ plays the major role for high activity. In H2O2 decomposition, Co2+ reveals itself to be of major importance. Redox active cations in the structure enhance the catalytic activity in all reactions. A benefit of a predominant 111 surface termination depends on the cobalt oxidation state in the as-prepared catalysts and the investigated reaction. © 2021 The Authors. Chemistry - A European Journal published by Wiley-VCH GmbH

Despite outstanding accomplishments in catalyst discovery, finding new, more efficient, environmentally neutral, and noble metal-free catalysts remains challenging and unsolved. Recently, complex solid solutions consisting of at least five different elements and often named as high-entropy alloys have emerged as a new class of electrocatalysts for a variety of reactions. The multicomponent combinations of elements facilitate tuning of active sites and catalytic properties. Predicting optimal catalyst composition remains difficult, making testing of a very high number of them indispensable. We present the high-throughput screening of the electrochemical activity of thin film material libraries prepared by combinatorial co-sputtering of metals which are commonly used in catalysis (Pd, Cu, Ni) combined with metals which are not commonly used in catalysis (Ti, Hf, Zr). Introducing unusual elements in the search space allows discovery of catalytic activity for hitherto unknown compositions. Material libraries with very similar composition spreads can show different activities vs. composition trends for different reactions. In order to address the inherent challenge of the huge combinatorial material space and the inability to predict active electrocatalyst compositions, we developed a high-throughput process based on co-sputtered material libraries, and performed high-throughput characterization using energy dispersive X-ray spectroscopy (EDS), scanning transmission electron microscopy (SEM), X-ray diffraction (XRD) and conductivity measurements followed by electrochemical screening by means of a scanning droplet cell. The results show surprising material compositions with increased activity for the oxygen reduction reaction and the hydrogen evolution reaction. Such data are important input data for future data-driven materials prediction. [Figure not available: see fulltext.] © 2021, The Author(s).

Dry reforming of methane is considered a potential reaction for the utilization of waste greenhouse gases to generate valuable chemicals. However, catalyst deactivation under a harsh reaction condition appears as the main obstacle toward its commercialization. In the present work, a facile hydrothermal synthesis procedure was adopted to prepare a robust Ru-based catalyst. Among the various combinations, a 1% Ru supported over Zr0.5Ce0.5O2 nanorod catalyst showed enhanced coke resistance and almost stable activity during 200 h activity analysis. Promotion of Ru/Zr0.5Ce0.5O2 with an optimum amount of Gd2O3 improved catalyst stability, which was attributed to the strong interaction of Ru with Gd2O3 leading to smaller Ru particle size (∼5 nm) and an improved OSC was inhibiting coke deposition. Promotion with 0.5% Gd2O3 further lowered the apparent activation energy of methane conversion to ∼20.6 kcal/mol without changing the reaction orders significantly. DFT calculation confirmed, due to the orbital similarity, methane cracking is preferred over Ru atoms and CO2 activation occurred on Gd atoms. ©

Scanning electrochemical cell microscopy (SECCM) is increasingly applied to determine the intrinsic catalytic activity of single electrocatalyst particle. This is especially feasible if the catalyst nanoparticles are large enough that they can be found and counted in post-SECCM scanning electron microscopy images. Evidently, this becomes impossible for very small nanoparticles and hence, a catalytic current measured in one landing zone of the SECCM droplet cannot be correlated to the exact number of catalyst particles. We show, that by introducing a ruler method employing a carbon nanoelectrode decorated with a countable number of the same catalyst particles from which the catalytic activity can be determined, the activity determined using SECCM from many spots can be converted in the intrinsic catalytic activity of a certain number of catalyst nanoparticles.[Figure not available: see fulltext.] © 2021, The Author(s).

Among the various homogenous electrocatalysts, especially Re(bpy)(CO)3Cl and [Ni(cyclam)]2+ were shown to be highly efficient for the selective conversion of CO2 to CO at moderate potentials. However, a purposeful combination of a ReI tricarbonyl unit with a cyclam ligand hitherto received no attention. Herein, we report on a series of cyclam based Re complexes comprising the original {N4} as well as heteroatom-altered ligand frameworks, describe their synthesis, reveal their coordination behavior and furthermore investigate their performance towards the electrochemical CO2 reduction. © 2021 The Authors. Zeitschrift für anorganische und allgemeine Chemie published by Wiley-VCH GmbH

Electrochemical oxidation of biomass substrates to valuable bio-chemicals is highly attractive. However, the design of efficient, selective, stable, and inexpensive electrocatalysts remains challenging. Here it is reported how a 3D highly ordered mesoporous Co3O4/nickel foam (om-Co3O4/NF) electrode fulfils those criteria in the electrochemical oxidation of 5-hydroxymethylfurfural (HMF) to value-added 2,5-furandicarboxylic acid (FDCA). Full conversion of HMF and an FDCA yield of >99.8 % are achieved with a faradaic efficiency close to 100 % at a potential of 1.457 V vs. reversible hydrogen electrode. Such activity and selectivity to FDCA are attributed to the fast electron transfer, high electrochemical surface area, and reduced charge transfer resistance. More impressively, remarkable catalyst stability under long-term testing is obtained with 17 catalytic cycles. This work highlights the rational design of metal oxides with ordered meso-structures for electrochemical biomass conversion. © 2021 The Authors. ChemSusChem published by Wiley-VCH GmbH

Water electrolysis is a promising technology for sustainable hydrogen production; however, its commercialisation is limited by sluggish kinetics of the oxygen evolution reaction (OER). A potential alternative to the OER is hence required and is seen in the electrocatalytic glycerol oxidation reaction (GOR) as it offers concomitant value-added product generation from a cheap and abundant feedstock. Here, we show a facile solid-state synthesis method to obtain Ni-boride, a non-noble metal-based catalyst subsequently used in an in-depth study of the GOR product distribution as a function of key electrolysis parameters. Highly crystalline, mixed-phase Ni borides were obtained, and their synthesis was successfully optimised regarding GOR activity. Long-term chronoamperometry was conducted in a circular flow-through cell and samples were analysed by HPLC. It is shown that the formation of lactic acid, one of the most valuable GOR products, can be enhanced by optimising the electrolyte composition and the applied potential. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

Due to the high demand for renewable and infrastructure compatible energy conversion and storage technologies, research on organic fuel cells receives increasing interest again recently. Organic fuels such as alcohols provide an attractive avenue to overcome the drawbacks of hydrogen as an energy carrier. Particularly interesting are secondary alcohols that almost exclusively form ketones as the final oxidation product, as they can be utilized in “zero emission” concepts without CO2 as a by-product. The state-of-the-art electrocatalyst in secondary alcohol oxidation is Pt-Ru, which demonstrates low onset potentials for the oxidation of the most facile secondary alcohol isopropanol. Yet, the achievable current densities are still relatively low and decrease rapidly due to the formed product acetone, which can poison the catalyst surface over time. Therefore, there is an inevitable need for the development of novel electrocatalyst materials circumventing these challenges. In this study, we employ a high-throughput electrochemical approach coupled to on-line inductively-coupled plasma mass spectrometry to map the composition-dependent activity and stability of PtxIr100-x alloy electrocatalysts toward the electro-oxidation of isopropanol. The activity and stability of magnetron sputtered PtxIr100-x material libraries are studied in 0.1 M HClO4 both in the absence and presence of isopropanol. The highest current densities are achieved for the sample containing the least amount of Ir (3.4 at.%), with a continuous decrease with the increasing amount of Ir. The alloys are inactive towards the oxidation of isopropanol when the amount of Ir exceeded 80 at%. The presence of isopropanol also has a notable effect on stability: while dissolution rates do not change in the case of pure Pt and Ir, a significant increase in stability is observed for the PtxIr100-x thin-film samples at all applied upper potential limits. This is explained by the strong adsorption of acetone on the surface of the catalyst that inhibits the formation of surface oxides. © 2021 Elsevier Inc.

The complex interplay of restricted mass transport leading to local accumulation or depletion of educts, intermediates, products, counterions and co-ions influences the reactions at the active sites of electrocatalysts when electrodes are rough, three-dimensionally mesoporous or nanoporous. This influence is important with regard to activity, and even more to selectivity, of electrocatalytic reactions. The underlying principles are discussed based on the growing awareness of these considerations over recent years. © 2020 Elsevier B.V.

The aim to produce highly active, selective, and long-lived electrocatalysts by design drives major research efforts toward gaining fundamental understanding of the relationship between material properties and their catalytic performance. Surface characterization tools enable to assess atomic scale information on the complexity of electrocatalyst materials. Advancing electrochemical methodologies to adequately characterize such systems was less of a research focus point. In this Review, we shed light on the ability to gain fundamental insights into electrocatalysis from a complementary perspective and establish corresponding design strategies. These may rely on adopting the perceptions and models of other subareas of electrochemistry, such as corrosion, battery research, or electrodeposition. Concepts on how to account for and improve mass transport, manage gas bubble release, or exploit magnetic fields are highlighted in this respect. Particular attention is paid to deriving design strategies for nanoelectrocatalysts, which is often impeded, as structural and physical material properties are buried in electrochemical data of whole electrodes or even devices. Thus, a second major approach focuses on overcoming this difference in the considered level of complexity by methods of single-entity electrochemistry. The gained understanding of intrinsic catalyst performance may allow to rationally advance design concepts with increased complexity, such as three-dimensional electrode architectures. Many materials undergo structural changes upon formation of the working catalyst. Accordingly, developing "precatalysts"with low hindrance of the electrochemical transformation to the active catalyst is suggested as a final design strategy. ©

Selective oxidation of higher alcohols using heterogeneous catalysts is an important reaction in the synthesis of fine chemicals with added value. Though the process for primary alcohol oxidation is industrially established, there is still a lack of fundamental understanding considering the complexity of the catalysts and their dynamics under reaction conditions, especially when higher alcohols and liquid-phase reaction media are involved. Additionally, new materials should be developed offering higher activity, selectivity, and stability. This can be achieved by unraveling the structure–performance correlations of these catalysts under reaction conditions. In this regard, researchers are encouraged to develop more advanced characterization techniques to address the complex interplay between the solid surface, the dissolved reactants, and the solvent. In this mini-review, we report some of the most important approaches taken in the field and give a perspective on how to tackle the complex challenges for different approaches in alcohol oxidation while providing insight into the remaining challenges. © 2021 The Authors. Chemistry - A European Journal published by Wiley-VCH GmbH

Nature uses Fe porphyrin sites for the oxygen reduction reaction (ORR). Synthetic Fe porphyrins have been extensively studied as ORR catalysts, but activity improvement is required. On the other hand, Fe porphyrins have been rarely shown to be efficient for the oxygen evolution reaction (OER). We herein report an enzyme-inspired Fe porphyrin 1 as an efficient catalyst for both ORR and OER. Complex 1, which bears a tethered imidazole for Fe binding, beats imidazole-free analogue 2, with an anodic shift of ORR half-wave potential by 160 mV and a decrease of OER overpotential by 150 mV to get the benchmark current density at 10 mA cm−2. Theoretical studies suggested that hydroxide attack to a formal FeV=O form the O−O bond. The axial imidazole can prevent the formation of trans HO-FeV=O, which is less effective to form O−O bond with hydroxide. As a practical demonstration, we assembled rechargeable Zn-air battery with 1, which shows equal performance to that with Pt/Ir-based materials. © 2021 Wiley-VCH GmbH

Cu-based catalysts have shown structural instability during the electrochemical CO2reduction reaction (CO2RR). However, studies on monometallic Cu catalysts do not allow a nuanced differentiation between the contribution of the applied potential and the local concentration of CO as the reaction intermediate since both are inevitably linked. We first use bimetallic Ag-core/porous Cu-shell nanoparticles, which utilise nanoconfinement to generate high local CO concentrations at the Ag core at potentials at which the Cu shell is still inactive for the CO2RR. Usingoperandoliquid cell TEM in combination withex situTEM, we can unequivocally confirm that the local CO concentration is the main source for the Cu instability. The local CO concentration is then modulated by replacing the Ag-core with a Pd-core which further confirms the role of high local CO concentrations. Product quantification during CO2RR reveals an inherent trade-off between stability, selectivity and activity in both systems. © The Royal Society of Chemistry 2021.

Developing highly efficient and selective electrocatalysts for the CO2 reduction reaction to produce value-added chemicals has been intensively pursued. We report a series of CuxOyCz nanostructured electrocatalysts derived from a Cu-based MOF as porous self-sacrificial template. Blending catalysts with polytetrafluoroethylene (PTFE) on gas diffusion electrodes (GDEs) suppressed the competitive hydrogen evolution reaction. 25 to 50 wt % teflonized GDEs exhibited a Faradaic efficiency of ≈54 % for C2+ products at −80 mA cm−2. The local OH− ions activity of PTFE-modified GDEs was assessed by means of closely positioning a Pt-nanoelectrode. A substantial increase in the OH−/H2O activity ratio due to the locally generated OH− ions at increasing current densities was determined irrespective of the PTFE amount. © 2021 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH

Bimetallic silver-copper electrocatalysts are promising materials for electrochemical CO2 reduction reaction (CO2RR) to fuels and multi-carbon molecules. Here, we combine Ag core/porous Cu shell particles, which entrap reaction intermediates and thus facilitate the formation of C2+ products at low overpotentials, with gas diffusion electrodes (GDE). Mass transport plays a crucial role in the product selectivity in CO2RR. Conventional H-cell configurations suffer from limited CO2 diffusion to the reaction zone, thus decreasing the rate of the CO2RR. In contrast, in the case of GDE-based cells, the CO2RR takes place under enhanced mass transport conditions. Hence, investigation of the Ag core/porous Cu shell particles at the same potentials under different mass transport regimes reveals: (i) a variation of product distribution including C3 products, and (ii) a significant change in the local OH- activity under operation. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

Complex solid solutions (“high entropy alloys”), comprising five or more principal elements, promise a paradigm change in electrocatalysis due to the availability of millions of different active sites with unique arrangements of multiple elements directly neighbouring a binding site. Thus, strong electronic and geometric effects are induced, which are known as effective tools to tune activity. With the example of the oxygen reduction reaction, we show that by utilising a data-driven discovery cycle, the multidimensionality challenge raised by this catalyst class can be mastered. Iteratively refined computational models predict activity trends around which continuous composition-spread thin-film libraries are synthesised. High-throughput characterisation datasets are then used as input for refinement of the model. The refined model correctly predicts activity maxima of the exemplary model system Ag-Ir-Pd-Pt-Ru. The method can identify optimal complex-solid-solution materials for electrocatalytic reactions in an unprecedented manner. © 2021 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH

The electrochemical CO2 reduction (CO2R) is a promising approach to decrease the amount of CO2 in the atmosphere by producing commodity chemicals or fuels using renewable energies. Herein, the development of non-noble metal electrocatalysts is regarded as a key point for achieving the transition of CO2R to industrial scales. Transition metal chalcogenides of the pentlandite structure (M9X8) have emerged as promising electrocatalysts to produce syngas. In this line, we present the electrochemical CO2R of FexNi9-xS8 (x=3–6) with variable Fe : Ni ratios. All materials can reduce H2O/CO2 mixtures to CO or H2 respectively with varying efficiency depending on the Fe : Ni ratio and the water content. While CO2R in proton-rich organic electrolytes was mainly accompanied by hydrogen evolution, the CO2R activity climaxed with F.E. of 3.6 % for CO and 0.3 % for methane using Fe3Ni6S8. Using electrolytes with low water content, CO production with F.E. close to 90 % was demonstrated. Counterintuitively, the variation of the Fe : Ni ratio led only to small alterations in the CO2R activity. Quantum mechanical studies were performed to get further information on the observed trends and provide further insight into structure/activity relationships for the Fe/Ni pentlandite system and its CO2R activity opening the path towards the development of more active and robust CO2R electrocatalysts. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

The combination of nanostructured transition metal oxides and carbon materials is a promising approach to obtain inexpensive, highly efficient, and stable bifunctional electrocatalysts for the oxygen reduction (ORR) and the oxygen evolution (OER) reactions. We present a strategy for improving the bifunctional ORR/OER activity of supported FeCoOx nanoparticles by tuning the properties of multi-walled carbon nanotubes (MWCNT) via nitrogen doping during their synthesis in the presence of ammonia and subsequent oxidative functionalization. In-depth structural characterization indicates that oxidative treatment provides fine control of the dispersion and localization of FeCoOx nanoparticles in MWCNT, while the optimal degree of nitrogen doping leads to increased bifunctional activity due to enhanced electrical conductivity as well as improved catalyst stability, in both OER and ORR conditions, for nanoparticles formed by two different synthesis routes. The findings reported can be strategically considered for the design of high-performance reversible ORR/OER electrocatalysts. © 2021 The Authors. ChemElectroChem published by Wiley-VCH GmbH

The electrochemical reduction of CO2 is an attractive strategy towards the mitigation of environmental pollution and production of bulk chemicals as well as fuels by renewables. The bimetallic sulfide Fe4.5Ni4.5S8 (pentlandite) was recently reported as a cheap and robust catalyst for electrochemical water splitting, as well as for CO2 reduction with a solvent-dependent product selectivity. Inspired by numerous reports on monometallic sulfoselenides and selenides revealing higher catalytic activity for the CO2 reduction reaction (CO2RR) than their sulfide counterparts, the authors investigated the influence of stepwise S/Se exchange in seleno-pentlandites Fe4.5Ni4.5S8-YSeY (Y=1–5) and their ability to act as CO2 reducing catalysts. It is demonstrated that the incorporation of higher equivalents of selenium favors the CO2RR with Fe4.5Ni4.5S4Se4 revealing the highest activity for CO formation. Under galvanostatic conditions in acetonitrile, Fe4.5Ni4.5S4Se4 generates CO with a Faradaic Efficiency close to 100 % at applied current densities of −50 mA cm−2 and −100 mA cm−2. This work offers insight into the tunability of the pentlandite based electrocatalysts for the CO2 reduction reaction. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Metal alloy catalysts can develop complex surface structures when exposed to reactive atmospheres. The structures of the resulting surfaces have intricate relationships with a myriad of factors, such as the affinity of the individual alloying elements to the components of the gas atmosphere and the bond strengths of the multitude of low-energy surface compounds that can be formed. Identifying the atomic structure of such surfaces is a prerequisite for establishing structure-property relationships, as well as for modeling such catalysts in ab initio calculations. Here, we show that an alloy, consisting of an oxophilic metal (Cu) diluted into a noble metal (Ag), forms a meta-stable two-dimensional oxide monolayer, when the alloy is subjected to oxidative reaction conditions. The presence of this oxide is correlated with selectivity in the corresponding test reaction of ethylene epoxidation. In the present study, using a combination of in situ, ex situ, and theoretical methods (NAP-XPS, XPEEM, LEED, and DFT), we determine the structure to be a two-dimensional analogue of Cu2O, resembling a single lattice plane of Cu2O. The overlayer holds a pseudo-epitaxial relationship with the underlying noble metal. Spectroscopic evidence shows that the oxide's electronic structure is qualitatively distinct from its three-dimensional counterpart, and because of weak electronic coupling with the underlying noble metal, it exhibits metallic properties. These findings provide precise details of this peculiar structure and valuable insights into how alloying can enhance catalytic properties. Copyright © 2020 American Chemical Society.

Direct mechanocatalysis describes catalytic reactions under the involvement of mechanical energy with the distinct feature of milling equipment itself being the catalyst. This novel type of catalysis features no solubility challenges of the catalysts nor the substrate and on top offering most facile way of separation. © 2020 The Authors. Published by Wiley-VCH GmbH

The influence of impurities in steel mill exhaust gases on ternary Cu/ZnO/Al2O3 catalysts was studied for conventional methanol synthesis, which is one of the central reactions within the cross-industrial approach of Carbon2Chem®. A series of hydrocarbons was identified as inert spectators for methanol synthesis. Several catalyst poisons like N-containing compounds or O2 show reversible characteristics at low pressure. However, by increasing the partial pressure of O2, poisoning becomes irreversible, indicating different poisoning mechanisms concerning the reversibility of deactivation. © 2020 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Direct valorization of ethane, a substantial component of shale gas deposits, at mild conditions remains a significant challenge, both from an industrial and an academic point of view. Herein, we report iodine as an efficient and selective catalyst for the functionalization of ethane in oleum at low temperatures and pressures. A thorough study of relevant reaction parameters revealed iodine to be remarkably more active than the previously reported "Periana/Catalytica"catalyst under optimized conditions. As a result of a fundamentally different catalytic cycle, iodine yields the bis-bisulfate ester of ethylene glycol (HO3SO-CH2-CH2-OSO3H, EBS), whereas for state-of-the-art platinum-based catalysts ethionic acid (HO3S-CH2-CH2-OSO3H, ETA) is obtained as the main product. Our findings open up an attractive route for the direct conversion of ethane toward ethylene glycol. © 2020 American Chemical Society.

The heterogeneously catalysed reaction of hydrogen with carbon monoxide and carbon dioxide (syngas) to methanol is nearly 100 years old, and the standard methanol catalyst Cu/ZnO/Al2O3 has been applied for more than 50 years. Still, the nature of the Zn species on the metallic Cu0 particles (interface sites) is heavily debated. Here, we show that these Zn species are not metallic, but have a positively charged nature under industrial methanol synthesis conditions. Our kinetic results are based on a self-built high-pressure pulse unit, which allows us to inject selective reversible poisons into the syngas feed passing through a fixed-bed reactor containing an industrial Cu/ZnO/Al2O3 catalyst under high-pressure conditions. This method allows us to perform surface-sensitive operando investigations as a function of the reaction conditions, demonstrating that the rate of methanol formation is only decreased in CO2-containing syngas mixtures when pulsing NH3 or methylamines as basic probe molecules. © 2020, The Author(s).

Pd nanoparticles deposited on nitrogen-doped mesoporous carbon are promising catalysts for highly selective and effective catalytic hydrogenation reactions. To design and utilize these novel catalysts, it is essential to understand the effect of N doping on the metal-support interactions. A combined experimental (X-ray photoelectron spectroscopy) and computational (density functional theory) approach is used to identify preferential adsorption sites and to give detailed explanations of the corresponding metal-support interactions. Pyridinic N atoms turned out to be the preferential adsorption sites for Pd nanoparticles on nitrogen-doped mesoporous carbon, interacting through their lone pairs (LPs) with the Pd atoms via N-LP-Pd dσ and N-LP-Pd s and Pd dπ-π∗ charge transfer, which leads to a change in the Pd oxidation state. Our results evidence the existence of bifunctional palladium nanoparticles containing Pd0 and Pd2+ centers. © the Owner Societies.

The electrocatalytic reduction of carbon dioxide (CO2) by means of renewable energies is widely recognized as a promising approach to establish a sustainable closed carbon cycle economy. However, widespread application is hampered by the inherent difficulty in suppressing the hydrogen evolution reaction and controlling the overall process selectivity. Further critical parameters are the limited solubility of CO2 in many electrolytes and its hindered mass transport to the electrodes. Herein we report on a series of nanoparticle Cu electrocatalysts on different carbon supports and their potential to perform the electrochemical CO2 reduction under supercritical conditions (scCO2). Herein, CO2 serves as the reaction medium and reactant alike. By a detailed comparison to ambient conditions we show that scCO2 conditions largely suppress the undesirable hydrogen evolution and favor the production of formic acid by the Cu electrodes. Furthermore, we show that scCO2 conditions significantly prevent Cu nanoparticle agglomeration during electrocatalysis. © 2020 American Chemical Society.

Carbon corrosion at high anodic potentials is a major source of instability, especially in acidic electrolytes and impairs the long-term functionality of electrodes. In-depth investigation of carbon corrosion in alkaline environment by means of differential electrochemical mass spectrometry (DEMS) is prevented by the conversion of CO2 into CO3 2−. We report the adaptation of a DEMS system for online CO2 detection as the product of carbon corrosion in alkaline electrolytes. A new cell design allows for in situ acidification of the electrolyte to release initially dissolved CO3 2− as CO2 in front of the DEMS membrane and its subsequent detection by mass spectrometry. DEMS studies of a carbon-supported nickel boride (NixB/C) catalyst and Vulcan XC 72 at high anodic potentials suggest protection of carbon in the presence of highly active oxygen evolution electrocatalysts. Most importantly, carbon corrosion is decreased in alkaline solution. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Contaminants in an electrochemical cell converting CO2 to formic acid can lead to the deactivation of cathode catalysts through several pathways, causing severe performance loss over time. Potential contaminants from flue gas emissions of principal fossil fuels include N2, O2, H2O, CO, NO2, SO2, particulate matter and hydrocarbons. Contaminant effects on the CO2 to formic acid electroreduction are scarcely covered in the literature. We describe in the present study these effects based on catalysts reported for the electroreduction of CO2 to formic acid, focusing principally on copper, tin and lead in the two most popular configurations, 2 and 3 compartment cells. Water solubility, metal affinity through chemisorption, known chemical reactions and altered electrochemical activities are the main focus of this review. We herein highlight that O2, SO2 and particulate matter have especially detrimental effects. While O2 can be efficiently removed from flue gas, additional treatment to remove SO2 and particulate matter is required. Our conclusions should raise interest in experimentally validating the effect of such contaminants. © 2020 Elsevier Ltd.

Intensive research is being conducted into highly efficient and cheap nanoscale materials for the electrocatalytic oxidation of water. In this context, we built heterostructures of multilayered CoNi-cyanide bridged coordination (CoNi-CP) nanosheets and graphene oxide (GO) sheets (CoNi-CP/GO) as a source for heterostructured functional electrodes. The layered CoNi-CP/GO hybrid components heated in nitrogen gas (N2) at 450 °C yield CoNi-based carbide (CoNi-C) through thermal decomposition of CoNi-CP, while GO is converted into reduced GO (rGO) to finally form a CoNi-C/rGO-450 composite. The CoNi-C/rGO-450 composite shows a reasonable efficiency for oxygen evolution reaction (OER) through water oxidations in alkaline solution. Meanwhile, regulated annealing of CoNi-CP/GO in N2 with thiourea at 450 and 550 °C produces CoNi-based sulfide (CoNi-S) rather than CoNi-C between rGO sheets co-doped by nitrogen (N) and sulfur (S) heteroatoms (NS-rGO) to form CoNi-S/NS-rGO-450 and CoNi-S/NS-rGO-550 composites, respectively. The CoNi-S/NS-rGO-550 shows the best efficiency for electrocatalytic OER among all electrodes with an overpotential of 290 mV at 10 mA cm-2 and a Tafel slope of 79.5 mV dec-1. By applying the iR compensation to remove resistance of the solution (2.1 ω), the performance is further improved to achieve a current density of 10 mA cm-2 at an overpotential of 274 mV with a Tafel slope of 70.5 mV dec-1. This result is expected to be a promising electrocatalyst compared to the currently used electrocatalysts and a step for fuel cell applications in the future. © 2020 American Chemical Society.

The trace-O2 removal in coke oven gas, which enables better utilization of its contained H2, is investigated with combinations of atmospheric nonthermal plasma and a Pt/γ-Al2O3 catalyst. Herein it is shown that a coaxial packed-bed dielectric barrier discharge (DBD) reactor removes up to 80 % O2 in a model coke oven gas. Along this line, the H2 content and the usage of Al2O3 granules in the plasma zone have been identified as major factors for the plasmachemical trace-O2 conversion. In contrast to the Pt/γ-Al2O3 catalyst, nonthermal plasma converts trace O2 at coke oven gas temperatures below 100 °C. © 2020 The Authors. Published by Wiley-VCH GmbH

Bimetallic Co-Cu catalysts are widely applied in higher alcohol synthesis (HAS), but the formation of the final active structure has not yet been fully clarified, especially for Co-rich catalysts. We investigated the structural evolution of a Co-Cu catalyst (Co:Cu = 2) from the hydrotalcite precursor containing additional Al3+ and Zn2+ to the final active state after 80 h under reaction conditions at 280 °C and 60 bar. The reconstruction of the bimetallic Co-Cu nanoparticles obtained by H2 reduction was induced by the feed gas consisting of an equimolar H2 and CO syngas mixture resulting in fast phase separation and sintering of metallic Cu0 and Co0 in the first 2 h time on stream (TOS) and a continuous carbidization of Co0 forming Co2C and its sintering until steady state was reached after 40 h TOS. An intergrowth of metallic Cu0 nanoparticles with Co2C nanoparticles was observed to occur under reaction conditions. The high selectivity to oxygenates amounting to 41% compared with 29% to hydrocarbons is ascribed to the multi-functional Co2C/Cu0 interface enabling dissociative CO adsorption, hydrogenation and CO insertion. The formation of hydrogenated carbon species (CxHy) originating from dissociative CO chemisorption is assumed to be favored by hydrogen spillover from Cu0 to Co2C. The adsorption sites for molecular CO provided by both Cu0 and Co2C facilitate its insertion into the CxHy intermediates thus leading to a higher selectivity to alcohols following the Anderson-Schulz-Flory distribution. © 2020 Elsevier Inc.

Complex solid solution electrocatalysts (often called high-entropy alloys) present a new catalyst class with highly promising features due to the interplay of multi-element active sites. One hurdle is the limited knowledge about structure-activity correlations needed for targeted catalyst design. We prepared Cr-Mn-Fe-Co-Ni nanoparticles by magnetron sputtering a high entropy Cantor alloy target simultaneously into an ionic liquid library. The synthesized nanoparticles have a narrow size distribution but different sizes (from 1.3 ± 0.1 nm up to 2.6 ± 0.3 nm), different crystallinity (amorphous, face-centered cubic or body-centered cubic) and composition (i.e. high Mn versus low Mn content). The Cr-Mn-Fe-Co-Ni complex solid solution nanoparticles possess an unprecedented intrinsic electrocatalytic activity for the oxygen reduction reaction in alkaline media, some of them even surpassing that of Pt. The highest intrinsic activity was obtained for body-centered cubic nanoparticles with a low Mn and Fe content which were synthesized using the ionic liquid 1-etyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [Emimi][(Tf)2N]. This journal is © The Royal Society of Chemistry.

Nanocrystalline corundum synthesized by ball milling of boehmite is found to be exceptionally robust toward chemical weathering, a common problem of transition aluminas in different applications, most notably in the case of supported catalysts, which are exposed to hydrothermal reaction environments. Detailed characterization and surface cation coordination analysis indicate that the absence of tetrahedral Al species on corundum makes it stable toward chemical weathering. A cobalt catalyst developed using nano-α-Al2O3 as the support showed Fischer-Tropsch synthesis activity and selectivity comparable to the benchmark Co/γ-Al2O3 and remained stable over 250 h on-stream. Copyright © 2020 American Chemical Society.

Spray-flame synthesis was used to produce high-surface-area perovskite electrocatalysts with high phase purity, minimum surface contamination, and high electrochemical stability. In this study, as-prepared LaCo1–xFexO3 perovskite nanoparticles (x=0.2, 0.3, and 0.4) were found to contain a high degree of combustion residuals, and mostly consist of both, stoichiometric and oxygen-deficient perovskite phases. Heating them at moderate temperature (250 °C) in oxygen could remove combustion residuals and increases the content of stoichiometric perovskite while preventing particle growth. A higher surface crystallinity was observed with increasing iron content coming along with a rise in oxygen deficient phases. With heat treatment, OER activity and stability of perovskites improved at 30 and 40 at.% Fe while deteriorating at 20 at.% Fe. This study highlights spray-flame synthesis as a promising technique to synthesize highly active nanoscale perovskite catalysts with improved OER activity. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Carbon is a frequently used electrode material and an important additive in catalyst films. Its corrosion is often reported during electrocatalysis at high anodic potentials, especially in acidic electrolyte. Investigation of the carbon corrosion in alkaline environment is difficult due to the CO2/CO32− equilibrium. We report the on-line determination of electrolysis products generated on NixB/C hybrid electrocatalysts in alkaline electrolyte at anodic potentials using differential electrochemical mass spectrometry (DEMS). NixB/C catalyst films were obtained from mixtures containing different ratios of NiXB and benzoxazine monomers followed by polymerization and pyrolysis. The impact of the composition of the electrocatalyst on the dominant electrolysis process allows to distinguish between the oxygen evolution reaction and carbon corrosion using DEMS results as well as the catalyst surface composition evaluated from X-ray photoelectron spectra. At the imposed highly oxidative conditions, an increasing amount of NixB in the electrocatalyst leads to a suppression of carbon corrosion. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

The use of rotating disk electrodes modified with multicomponent catalyst inks is common practice in electrocatalysis. In this work, we present a numerical model to simulate the effect of altered mass transport and conductivity inside a catalyst film, consisting of catalytically active nanoparticles and an inert binder material. Implications for the classical Tafel analysis are evaluated at different combinations of film resistances and mass transport properties. We show that in some cases, linear Tafel-like voltammetric responses may result, which do not contain actual kinetic information and might therefore be misleading and cause of erroneous catalyst activity evaluation. © 2020 Elsevier B.V.

The use of a microscale atmospheric pressure plasma jet (μAPPJ) was investigated for its potential to supply hydrogen peroxide in biocatalysis. Compared to a previously employed dielectric barrier discharge (DBD), the μAPPJ offered significantly higher H2O2 production rates and better handling of larger reaction volumes. The performance of the μAPPJ was evaluated with recombinant unspecific peroxygenase from Agrocybe aegerita (rAaeUPO). Using plasma-treated buffer, no side reactions with other plasma-generated species were detected. For long-term treatment, rAaeUPO was immobilized, transferred to a rotating bed reactor, and reactions performed using the μAPPJ. The enzyme had a turnover of 36,415 mol mol−1 and retained almost full activity even after prolonged plasma treatment. Overall, the μAPPJ presents a promising plasma source for plasma-driven biocatalysis. © 2020 The Authors. Published by Wiley-VCH GmbH

The elimination of waste and by-product generation and reduced dependence on hazardous chemicals are the key steps towards environmentally sustainable chemical transformations. Heterogeneously catalysed oxidation of cyclohexene with environmentally friendly oxidizing agents such as O2, H2O2 and tert-butyl hydroperoxide (TBHP) has great potential to replace existing processes using stoichiometric oxidants. A series of spray-flame synthesised nanoparticulate LaCo1-xFexO3 catalysts was employed for cyclohexene oxidation, and the comparative results showed that TBHP led to the highest initial activity and allylic selectivity, but O2 resulted in higher conversion for longer reaction times. Furthermore, the influence of Fe substitution was studied, which did not show any beneficial synergistic effects. LaCoO3 was found to be the optimum catalyst for cyclohexene oxidation with O2, following first-order reaction kinetics with an apparent activation energy of 57 kJ mol-1. The catalyst showed good reusability due to its highly stable particle size, morphology and perovskite structure. 7-Oxabicyclo[4.1.0]heptan-2-one was identified to be formed by the oxidation of 2-cyclohexene-1-one with 2-cyclohexene-1-hydroperoxide. © 2020 The Royal Society of Chemistry.

Mo-doped BiVO4 has emerged as a promising material for photoelectrodes for photoelectrochemical water splitting, however, still shows a limited efficiency for light-driven water oxidation. We present the influence of an oxygen-evolution catalyst composed of Ni, Fe, and Cr oxides on the activity of Mo:BiVO4 photoanodes. The photoanodes are prepared by spray-coating, enabling compositional and thickness gradients of the incorporated catalyst. Two different configurations are evaluated, namely with the catalyst embedded into the Mo:BiVO4 film or deposited on top of it. Both configurations provide a significantly different impact on the photoelectrocatalytic efficiency. Structural characterisation of the materials by means of SEM, TEM and XRD as well as the photoelectrocatalytic activity investigated by means of an optical scanning droplet cell and in situ detection of oxygen using scanning photoelectrochemical microscopy are presented. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Nickel-based nanostructured materials have gained widespread attention, particularly for energy-related applications. Employing chemical vapor deposition (CVD) for NiO necessitates suitable nickel precursors that are volatile and stable. Herein, we report the synthesis and characterization of a series of new nickel β-ketoiminato complexes with different aliphatic and etheric side chain substitutions, namely, bis(4-(isopropylamino)-pent-3-en-2-onato)nickel(II) ([Ni(ipki)2], 1), bis(4-(2-methoxyethylamino)pent-3-en-2-onato)nickel(II) ([Ni(meki)2], 2), bis(4-(2-ethoxyethylamino)pent-3-en-2-onato)nickel(II) ([Ni(eeki)2], 3), bis(4-(3-methoxy-propylamino)-pent-3-en-2-onato)nickel(II) ([Ni(mpki)2], 4), and bis(4-(3-ethoxypropylamino)pent-3-en-2-onato)nickel(II) ([Ni(epki)2], 5). These compounds have been thoroughly characterized with regard to their purity and identity by means of nuclear magnetic resonance spectroscopy (NMR) and electron impact mass spectrometry (EI-MS). Contrary to other transition metal β-ketoiminates, the imino side chain strongly influences the structural geometry of the complexes, which was ascertained via single-crystal X-ray diffraction (XRD). As a result, the magnetic momenta of the molecules also differ significantly as evidenced by the magnetic susceptibility measurements employing Evan's NMR method in solution. Thermal analysis revealed the suitability of these compounds as new class of precursors for CVD of Ni containing materials. As a representative precursor, compound 2 was evaluated for the CVD of NiO thin films on Si(100) and conductive glass substrates. The as-deposited nanostructured layers were stoichiometric and phase pure NiO as confirmed by XRD, Rutherford backscattering spectrometry (RBS), and nuclear reaction analysis (NRA). X-ray photoelectron spectroscopy (XPS) indicated the formation of slightly oxygen-rich surfaces. The assessment of NiO films in electrocatalysis revealed promising activity for the oxygen evolution reactions (OER). The current densities of 10 mA cm-2 achieved at overpotentials ranging between 0.48 and 0.52 V highlight the suitability of the new Ni complexes in CVD processes for the fabrication of thin film electrocatalysts. Copyright © 2020 American Chemical Society.

Abstract: Carbon supported phosphoric acid (H3PO4/C) was found to be a more productive catalyst for the gas-phase synthesis of the diesel fuel additive/substitute oxymethylene ethers (OME) as compared to benchmark zeolite catalysts. In this contribution, the performance of catalysts H3PO4/C and related H2PO4 −/C and HPO4 2−/C materials in OME synthesis from methanol and formaldehyde is described. Graphic Abstract: [Figure not available: see fulltext.]. © 2020, The Author(s).

Monometallic Mo and W carbides as well as highly mixed (Mo,W) carbides with various Mo/W ratios were synthesized directly on oxygen-functionalized carbon nanotubes (OCNTs), and used as noble-metal-free electrocatalysts in the hydrogen evolution reaction (HER) under both acidic and alkaline conditions. A purely orthorhombic structure was found in both monometallic and mixed carbide samples by X-ray diffraction. Transmission electron microscopy images showed that the carbide particles were highly dispersed on the OCNTs with well-controlled particle size. The homogeneous distribution of Mo and W in the carbides was confirmed by elemental mapping. (Mo,W)2C/OCNT with a Mo/W ratio of 3 : 1 showed the lowest overpotential to reach a current density of 10 mA/cm2 (87 mV in 0.1 M KOH and 92 mV in 0.5 M H2SO4), and the smallest Tafel slope of 34 mV/dec. Long-term stability under both alkaline and acidic conditions was demonstrated for 24 h. Our results revealed that an optimal amount of W in the mixed carbide can significantly improve its performance in the HER following the Tafel reaction pathway, most likely due to the weakened Mo−Hads bond. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Successful design of reversible oxygen electrocatalysts does not only require to consider their activity towards the oxygen reduction (ORR) and the oxygen evolution reactions (OER), but also their electrochemical stability at alternating ORR and OER operating conditions, which is important for potential applications in reversible electrolyzers/fuel cells or metal/air batteries. We show that the combination of catalyst materials containing stable ORR active sites with those containing stable OER active sites may result in a stable ORR/OER catalyst if each of the active components can satisfy the current demand of their respective reaction. We compare the ORR/OER performances of oxides of Mn (stable ORR active sites), Fe (stable OER active sites), and bimetallic Mn0.5Fe0.5 (reversible ORR/OER catalyst) supported on oxidized multi-walled carbon nanotubes. Despite the instability of Mn and Fe oxide for the OER and the ORR, respectively, Mn0.5Fe0.5 exhibits high stability for both reactions. © 2020, The Author(s).

The kinetics of higher alcohol synthesis was investigated using a hydrotalcite-derived Co-Cu-based catalyst aiming at a deeper understanding of the complex reaction network. At steady state similar chain growth probabilities of about 0.4 according to the Anderson-Schulz-Flory distribution were observed for alcohols, hydrocarbons and olefins indicating common intermediates. Alkanes were found to be formed consecutively from primarily formed olefins. The observed decrease of the selectivities to alcohols with increasing CO conversion at higher temperatures and higher residence times is ascribed to an increased availability of adsorbed atomic hydrogen, which decreases the saturated coverage of CO-derived CxHyOz species favoring hydrocarbon formation. Correspondingly, reaction orders of 0 and 0.8 for CO and H2, respectively, were derived based on a power-law approach including an apparent activation energy of 140 kJ mol−1. A reaction network based on the CO insertion factor was established, in which the competing reactions β-hydrogen elimination, chain growth and CO insertion proceed from common adsorbed CxHy intermediates. Selective higher alcohol formation was favored at low temperatures and short residence times, high pressures and a moderate H2:CO ratio of 1 requiring a compromise between conversion and selectivity. © 2020 Elsevier Inc.

Producing stable but active materials is one of the enduring challenges in electrocatalysis and other types of catalysis. Producing branched nanoparticles is one potential solution. Controlling the number of branches and branch size of faceted branched nanoparticles is one of the major synthetic challenges to achieve highly active and stable nanocatalysts. Herein, we use a cubic-core hexagonal-branch mechanism to synthesize branched Ru nanoparticles with control over the size and number of branches. This structural control is the key to achieving high exposure of active {10–11} facets and optimum number of Ru branches that enables improved catalytic activity for oxygen evolution reaction while maintaining high stability. © 2020 Wiley-VCH GmbH

Transition metal oxides are attractive catalyst alternatives in liquid-phase oxidation reactions due to their lower cost and higher abundance compared with conventional noble metal catalysts. We investigated the catalytic properties of a systematic series of Co3-xFexO4 spinel catalysts synthesized by a hard-templating method, which were applied in the liquid-phase oxidation of styrene, benzyl alcohol and cinnamyl alcohol. O2 and tert-butyl hydroperoxide (TBHP) were used as the oxidants in a comparative manner. For alcohol oxidation, TBHP leads to similar or slightly higher selectivity to the corresponding aldehydes compared with O2. For the activation of C=C bonds, TBHP favors the oxidative cleavage pathway, while O2 favors the epoxidation pathway. The comparison of the catalytic performance revealed that the activity of Co3O4 does not benefit from Fe doping using O2 as the oxidant, while the substitution of Fe ≤ 10 % in the spinel structure is beneficial when TBHP is used. This is attributed to the different activation mechanisms of the oxidizing agents, being spin transfer in case of O2 and partial decomposition in case of TBHP. Heterogeneity tests and reusability studies demonstrated the stability of the spinel catalysts. © 2020 Elsevier B.V.

Cryptomelane (α-(K)MnO2) powders were synthesized by different methods leading to only slight differences in their bulk crystal structure and chemical composition, while the BET surface area and the crystallite size differed significantly. Their performance in the oxygen evolution reaction (OER) covered a wide range and their sequence of increasing activity differed when electrocatalysis in alkaline electrolyte and chemical water oxidation using Ce4+ were compared. The decisive factors that explain this difference were identified in the catalysts’ microstructure. Chemical water oxidation activity is substantially governed by the exposed surface area, while the electrocatalytic activity is determined largely by the electric conductivity, which was found to correlate with the particle morphology in terms of needle length and aspect ratio in this sample series. This correlation is rather explained by an improved conductivity due to longer needles than by structure sensitivity as was supported by reference experiments using H2O2 decomposition and carbon black as additive. The most active catalyst R-cryptomelane reached a current density of 10 mA cm−2 at a potential 1.73 V without, and at 1.71 V in the presence of carbon black. The improvement was significantly higher for the catalyst with lower initial activity. However, the materials showed a disappointing catalytic stability during alkaline electrochemical OER, whereas the crystal structure was found to be stable at working conditions. © 2020 The Authors. Published by Wiley-VCH GmbH

Layered double hydroxides (LDHs) are presently among the best-performing oxygen evolution reaction (OER) electrocatalysts in alkaline media. The high activity of LDHs is due to synergistic effects between two transition metals as well as the layered structure which facilitates electron transfer. Because of a perfect match with the size of interlayer carbonate a ratio of 2:1 for the di- and tri-valent octahedral cations is energetically preferred. Here we present a strategy, where first mixed valent (Co2+ 1-zFe2+ z)4 Fe3+ 2 - LDHs, with z values between 0 and 0.75 are synthesized, which are subsequently oxidized to Co2+Fe3+ LDH-type layered (oxy)hydroxides with an unusual high trivalent Fe content. Characterization of the chemically oxidized materials using bulk and surface techniques demonstrated the successful synthesis of LDH-like trivalent iron rich (Co2+)4-4z (Fe3+)2+4z (oxy)hydroxides with a final Fe content ranging from 33.3 to 83.3%. Current densities of up to 200 mA cm−2 were obtained at potentials lower than 1.7 V vs. RHE for (Co2+)4-4z (Fe3+)2+4z (oxy)hydroxides containing a maximum of 80% Fe. © 2020 Elsevier Ltd

Electrocatalytic nanoparticles that mimic the three-dimensional geometric architecture of enzymes where the reaction occurs down a substrate channel isolated from bulk solution, referred to herein as nanozymes, were used to explore the impact of nano-confinement on electrocatalytic reactions. Surfactant covered Pt-Ni nanozyme nanoparticles, with Ni etched from the nanoparticles, possess a nanoscale channel in which the active sites for electrocatalysis of oxygen reduction are located. Different particle compositions and etching parameters allowed synthesis of nanoparticles with different average substrate channel diameters that have varying amounts of nano-confinement. The results showed that in the kinetically limited regime at low overpotentials, the smaller the substrate channels the higher the specific activity of the electrocatalyst. This is attributed to higher concentrations of protons, relative to bulk solution, required to balance the potential inside the nano-confined channel. However, at higher overpotentials where limitation by mass transport of oxygen becomes important, the nanozymes with larger substrate channels showed higher electrocatalytic activity. A reaction-diffusion model revealed that the higher electrocatalytic activity at low overpotentials with smaller substrate channels can be explained by the higher concentration of protons. The model suggests that the dominant mode of mass transport to achieve these high concentrations is by migration, exemplifying how nano-confinement can be used to enhance reaction rates. Experimental and theoretical data show that under mass transport limiting potentials, the nano-confinement has no effect and the reaction only occurs at the entrance of the substrate channel at the nanoparticle surface. © The Royal Society of Chemistry.

In recent years, metal-rich sulfides of the pentlandite type (M9S8) have attracted considerable attention for energy storage applications. However, common synthetic routes towards pentlandites either involve energy intensive high temperature procedures or solvothermal methods with specialized precursors and non-sustainable organic solvents. Herein, we demonstrate that ball milling is a simple and efficient method to synthesize nanosized bimetallic pentlandite particles (Fe4.5Ni4.5S8, Pn) with an average size of ca. 250 nm in a single synthetic step from elemental- or sulfidic mixtures. We herein highlight the effects of the milling ball quantity, precursor types and milling time on the product quality. Along this line, Raman spectroscopy as well as temperature/pressure monitoring during the milling processes provide valuable insights into mechanistic differences between the mechanochemical Pn-formation. By employing the obtained Pn-nanosized particles as cathodic electrocatalysts for water splitting in a zero-gap PEM electrolyzer we provide a comprehensive path for a potential sustainable future process involving non-noble metal catalysts. © 2020 The Royal Society of Chemistry.

[FeFe] hydrogenases are highly efficient catalysts for reversible dihydrogen evolution. H2 turnover involves different catalytic intermediates including a recently characterized hydride state of the active site (H-cluster). Applying cryogenic infrared and electron paramagnetic resonance spectroscopy to an [FeFe] model hydrogenase from Chlamydomonas reinhardtii (CrHydA1), we have discovered two new hydride intermediates and spectroscopic evidence for a bridging CO ligand in two reduced H-cluster states. Our study provides novel insights into these key intermediates, their relevance for the catalytic cycle of [FeFe] hydrogenase, and novel strategies for exploring these aspects in detail. Copyright © 2020 American Chemical Society.

A universal nano-capillary based method for sample deposition on the silicon nitride membrane of liquid-cell transmission electron microscopy (LCTEM) chips is demonstrated. It is applicable to all substances which can be dispersed in a solvent and are suitable for drop casting, including catalysts, biological samples, and polymers. Most importantly, this method overcomes limitations concerning sample immobilization due to the fragility of the ultra-thin silicon nitride membrane required for electron transmission. Thus, a straightforward way is presented to widen the research area of LCTEM to encompass any sample which can be externally deposited beforehand. Using this method, NixB nanoparticles are deposited on the μm-scale working electrode of the LCTEM chip and in situ observation of single catalyst particles during ethanol oxidation is for the first time successfully monitored by means of TEM movies. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

We report an unprecedented dinuclear catalyst for the electrochemical hydrogen evolution reaction (HER). A macrocyclic porphyrin complex comprising two nickel centres connected via redox mediating linker molecules gives rise to efficient catalysis, significantly outperforming a mononuclear reference catalyst. This journal is © The Royal Society of Chemistry.

Controlling the formation of nanosized branched nanoparticles with high uniformity is one of the major challenges in synthesizing nanocatalysts with improved activity and stability. Using a cubic-core hexagonal-branch mechanism to form highly monodisperse branched nanoparticles, we vary the length of the nickel branches. Lengthening the nickel branches, with their high coverage of active facets, is shown to improve activity for electrocatalytic oxidation of 5-hydroxymethylfurfural (HMF), as an example for biomass conversion. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA

Electrochemical dealloying as a post-Treatment can greatly improve the catalytic activity of nanoparticles. To date, selecting suitable conditions to reach desired porosity, composition and catalytic activity is based on trial-And-error-Attempts, due to insufficient understanding of the electrochemically induced morphological and compositional changes of the nanoparticles. These changes are elucidated here by combining electrochemistry with identical location electron microscopy analyses and linking them to the electrocatalytic properties of the obtained nanocatalysts. Using AgAu alloy nanoparticles and the hydrogen evolution reaction as a model system, the influence of cyclic voltammetry parameters on the catalytic activity upon electrochemical dealloying is investigated. Increasing the number of cycles initially results in a decreased Ag content and a sharp improvement in activity. Additional dealloying increases the nanoparticle porosity, while marginally altering their composition, due to surface motion of atoms. Since this is accompanied by particle aggregation, a decrease in catalytic activity results upon extensive cycling. This transition between porosity formation and particle aggregation marks the optimum for nanocatalyst post-production. The gained insights may aid speeding up the development of new materials by electrochemical dealloying as an easy-To-control post-processing route to tune the properties of existing nanoparticles, instead of having to alter usually delicate synthesis routes as a whole. © The Royal Society of Chemistry.

Discovering precious metal-free electrocatalysts exhibiting high activity and stability toward both the oxygen reduction (ORR) and the oxygen evolution (OER) reactions remains one of the main challenges for the development of reversible oxygen electrodes in rechargeable metal–air batteries and reversible electrolyzer/fuel cell systems. Herein, a highly active OER catalyst, Fe0.3Ni0.7OX supported on oxygen-functionalized multi-walled carbon nanotubes, is substantially activated into a bifunctional ORR/OER catalyst by means of additional incorporation of MnOX. The carbon nanotube-supported trimetallic (Mn-Ni-Fe) oxide catalyst achieves remarkably low ORR and OER overpotentials with a low reversible ORR/OER overvoltage of only 0.73 V, as well as selective reduction of O2 predominantly to OH−. It is shown by means of rotating disk electrode and rotating ring disk electrode voltammetry that the combination of earth-abundant transition metal oxides leads to strong synergistic interactions modulating catalytic activity. The applicability of the prepared catalyst for reversible ORR/OER electrocatalysis is evaluated by means of a four-electrode configuration cell assembly comprising an integrated two-layer bifunctional ORR/OER electrode system with the individual layers dedicated for the ORR and the OER to prevent deactivation of the ORR activity as commonly observed in single-layer bifunctional ORR/OER electrodes after OER polarization. © 2019 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

While [Ni(cyclam)]2+ and [Ni(dithiacyclam)]2+ complexes were shown to be potent electrocatalysts for the CO2 conversion, their respective Co complexes hitherto received only little attention. Herein, we report on the CoII complexes of the cyclam and dithiacyclam platform, describe their synthesis and reveal their rich solvent dependent coordination chemistry. We show that sulfur implementation into the cyclam moiety leads to a switch from a low spin CoII complex in [Co(cyclam)]2+ to a high spin form in [Co(dithiacyclam)]2+. Notably, while both complexes are capable to perform the reduction of CO2 to CO, H2 formation is generally preferred. Along this line, the complexes were shown to enable proton reduction from acetic acid. However, in comparison to [Co(cyclam)]2+, the altered electronics make [Co(dithiacyclam)]2+ complexes prone to deposit on the glassy carbon working electrode over time leading to an overall low faradaic efficiency for the reduction of protons or CO2. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

The suitability of a commercial and industrially applied Cu-based catalyst for the synthesis of methanol by CO2 hydrogenation was investigated. Unexpectedly, this system showed high stability and well-performance under conditions that may be relevant for chemical energy conversion using hydrogen and energy from renewable technologies. This Cu-based catalyst demonstrated excellent suitability for dynamical process operation that may be essential for effective compensation of the volatility of renewable energy sources. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

The promoting effect of cobalt on the catalytic activity of a NiCoO Dry Methane Reforming (DMR) catalyst was studied by a combination of in situ Kβ X-ray Emission Spectroscopy (XES) and Kβ-detected High Energy Resolution Fluorescence Detected X-ray absorption spectroscopy (HERFD XAS). Following the calcination process, Ni XES and Kβ-detected HERFD XAS data revealed that the NiO coordination in the NiCoO catalyst has a higher degree of symmetry and is different than that of pure NiO/γ-Al2O3. Following the reductive activation, it was found that the NiCoO/γ-Al2O3 catalyst required a relatively higher temperature compared to the monometallic NiO/γ-Al2O3 catalyst. This finding suggests that Co is hampering the reduction of Ni in the NiCoO catalyst by modulation of its electronic structure. It has also been previously shown that the addition of Co enhances the DMR activity. Further, the Kβ XES spectrum of the partly reduced catalysts at 450 °C reveals that the Ni sites in the NiCoO catalyst are electronically different from the NiO catalyst. The in situ X-ray spectroscopic study demonstrates that reduced metallic Co and Ni are the primary species present after reduction and are preserved under DMR conditions. However, the NiCo catalyst appears to always be somewhat more oxidized than the Ni-only species, suggesting that the presence of cobalt modulates the Ni electronic structure. The electronic structural modulations resulting from the presence of Co may be the key to the increased activity of the NiCo catalyst relative to the Ni-only catalyst. This study emphasizes the potential of in situ X-ray spectroscopy experiments for probing the electronic structure of catalytic materials during activation and under operating conditions. © The Royal Society of Chemistry.

Molecular design to improve catalyst performance is significant but challenging. In enzymes, residue groups that are close to reaction centers play critical roles in regulating activities. Using this bioinspired strategy, three water-soluble polymers were designed with appending Co porphyrins and different side-chain groups to mimic enzyme reaction centers and activity-controlling residue groups, respectively. With these polymers, high hydrogen evolution efficiency was achieved in neutral aqueous media for electro- (turnover frequency >2.3×104 s−1) and photocatalysis (turnover number >2.7×104). Porphyrin units are surrounded and protected by polymer chains, and more importantly, the activity can be tuned with different side-chain groups. Therefore, instead of revising molecular structures that is difficult from both design and synthesis points of view, polymers can be used to improve molecular solubility and stability and simultaneously regulate activity by using side-chain groups. © 2020 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

In plasma-driven biocatalysis, enzymes are employed to carry out reactions using species generated by non-thermal plasmas as the precursors. We have previously demonstrated that this is feasible in principle, but that the approach suffers from the short lifetime of the biocatalyst under operating conditions. In this work, protection strategies were investigated to prevent the dielectric barrier discharge plasma-induced inactivation of biocatalysts, using recombinant unspecific peroxygenase from Agrocybe aegerita (rAaeUPO), one of the most promising enzymes for plasma-driven biocatalysis. Treatment in oxygen-free atmospheres did not provide any advantage over treatment in synthetic air, indicating that the detrimental reactive species did not originate from oxygen in the plasma phase. Chemical scavengers were employed to eliminate undesired reactive species, without any long-term effect on enzyme lifetime. Similarly, chaperones, including the known stress response proteins Hsp33, CnoX, and RidA did not increase the lifetime of rAaeUPO. Immobilization of the biocatalyst proved effective in preserving enzyme activity. The residual activity of rAaeUPO after plasma treatment strongly depended on the specific immobilization support. Essentially complete protection for at least 15 min of plasma exposure was achieved with an epoxy-butyl-functionalized carrier. This study presents new insights into plasma-protein interactions and plots a path forward for protecting biocatalytic proteins from plasma-mediated inactivation. © 2020 IOP Publishing Ltd.

Functionalization of semiconductors by metallic nanoparticle is considered to be one of the most effective procedure to improve photocatalytic hydrogen production. Photodeposition is frequently used for functionalization but particle sizes and dispersions are still difficult to control. Here, Pt functionalization is achieved in a one-pot synthesis. The as-prepared samples are compared to reference materials prepared by conventional photodeposition and our results confirm that small and well-dispersed nanoparticles with superior stability are obtained by one-pot synthesis. The enhanced stability is attributed to a limited leaching of Pt nanoparticles during illumination likely caused by the preferable interaction of small, well dispersed Pt nanoparticles with the TiO2 support material. In addition, our results demonstrate that Na-residues are detrimental for the photocatalytic performance and washing in acidic solution is mandatory to effectively reduce the sodium contamination. © 2019 Elsevier B.V.

Variants of the highly active [NiFeSe] hydrogenase from D. vulgaris Hildenborough that exhibit enhanced O2 tolerance were used as H2-oxidation catalysts in H2/O2 biofuel cells. Two [NiFeSe] variants were electrically wired by means of low-potential viologen-modified redox polymers and evaluated with respect to H2-oxidation and stability against O2 in the immobilized state. The two variants showed maximum current densities of (450±84) μA cm−2 for G491A and (476±172) μA cm−2 for variant G941S on glassy carbon electrodes and a higher O2 tolerance than the wild type. In addition, the polymer protected the enzyme from O2 damage and high-potential inactivation, establishing a triple protection for the bioanode. The use of gas-diffusion bioanodes provided current densities for H2-oxidation of up to 6.3 mA cm−2. Combination of the gas-diffusion bioanode with a bilirubin oxidase-based gas-diffusion O2-reducing biocathode in a membrane-free biofuel cell under anode-limiting conditions showed unprecedented benchmark power densities of 4.4 mW cm−2 at 0.7 V and an open-circuit voltage of 1.14 V even at moderate catalyst loadings, outperforming the previously reported system obtained with the [NiFeSe] wild type and the [NiFe] hydrogenase from D. vulgaris Miyazaki F. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Metal-rich chalcogenides composed of highly abundant elements recently emerged as promising catalysts for the electrocatalytic hydrogen evolution reaction (HER). Many of these materials benefit from a high intrinsic conductivity as compared to their chalcogen-rich congeners, greatly reducing the necessity for conductive additives or sophisticated nanostructuring. Herein, we showcase the high potential of metal-rich transition-metal chalcogenides for the electrocatalytic hydrogen formation by summarizing the recent progress achieved with M9S8 (pentlandite type) and M3S2 (heazlewoodite type) based materials, which represent the most frequently applied compositions for this purpose. By a detailed electrochemical comparison of bulk as well as pellet electrodes of metal-rich Fe4.5Ni4.5S8, we also aim at raising awareness in the community for the inherent differences in catalytic properties of the materials themselves and those of the fabricated electrodes, a point that is often disregarded in reports on HER-catalyst systems. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

The rational design of high-performance and cost-effective electrocatalysts is a key for the development of sustainable energy systems such as electrolyzers, fuel cells and metal-air batteries. Although water splitting and fuel cells are commercially mature technologies, they are still limited on large scale primarily due to the abundancy of the currently utilized expensive materials as well as the sluggish kinetics of the underlaying reactions, oxygen evolution reaction (OER) and oxygen reduction reaction (ORR), and thus the required large observed overpotentials. Therefore, an efficient inexpensive catalyst is necessary. In the last decade, metal chalcogenides have been attractive materials in electrocatalysis of OER and ORR. Herein, we provide an overview on the recent advances on particularly metal-rich chalcogenides such as heazlewoodite- and pentlandite-types including their electrochemical activities and OER mechanisms. Likewise, examples of state-of-the-art metal chalcogenides revealing bifunctional activity for both OER and ORR are also presented. Diverse strategies to improve the catalytic performance are discussed and current challenges and future perspectives towards further development in this field are addressed. © 2020 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Complex solid-solution electrocatalysts (also referred to as high-entropy alloy) are gaining increasing interest owing to their promising properties which were only recently discovered. With the capability of forming complex single-phase solid solutions from five or more constituents, they offer unique capabilities of fine-tuning adsorption energies. However, the elemental complexity within the crystal structure and its effect on electrocatalytic properties is poorly understood. We discuss how addition or replacement of elements affect the adsorption energy distribution pattern and how this impacts the shape and activity of catalytic response curves. We highlight the implications of these conceptual findings on improved screening of new catalyst configurations and illustrate this strategy based on the discovery and experimental evaluation of several highly active complex solid solution nanoparticle catalysts for the oxygen reduction reaction in alkaline media. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Ultrafast construction of oxygen-containing scaffold over graphite for trapping Ni2+ into single atom catalysts (SACs) was developed and presented by a one-step electrochemical activation technique. The present method for Ni SACs starts with graphite foil and is capable of achieving ultrafast preparation (1.5 min) and mass production. The defective oxygen featuring the strong electronegativity enables primarily attracting Ni2+ ions and stabilizing Ni atoms via Ni-O6 coordination instead of conventional metal-C or metal-N. In addition, the oxygen defects for trapping are tunable through altering the applied voltage or electrolyte, further altering the loading of Ni atoms, indicative of enhanced oxygen evolution activity. This simple and ultrafast electrochemical synthesis is promising for the mass and controllable production of oxygen-coordinated Ni SACs, which exhibit good performance for oxygen evolution reaction. © 2020 American Chemical Society.

Breakthroughs toward effective water-splitting electrocatalysts for mass hydrogen production will necessitate material design strategies based on unexplored material chemistries. Herein, Ni-metalloid (B, Si, P, As, Te) alloys are reported as an emergent class of highly promising electrocatalysts for the oxygen evolution reaction (OER) and insight is offered into the origin of activity enhancement on the premise of the surface electronic structure, the OER activation energy, influence of the guest metalloid elements on the lattice structure of the host metal (Ni), and surface-oxidized metalloid oxoanions. The metalloids modify the lattice structure of Ni, causing changes in the nearest Ni–Ni interatomic distance (dNi–Ni). The activation energy Ea scales with dNi–Ni indicating an apparent dependence of the OER activity on lattice properties. During the OER, surface Ni atoms are oxidized to nickel oxyhydroxide, which is the active state of the catalyst, meanwhile, the surface metalloids are oxidized to the corresponding oxoanions that affect the interfacial electrode/electrolyte properties and hence the adsorption/desorption interaction energies of the reacting species. © 2019 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

A novel spectroelectrochemical ATR-FTIR thin-film cell was designed and applied to elucidate the intermediates during electrocatalytic alcohol oxidation. In the novel cell design, the working electrode is positioned coplanar above the internal reflection element (IRE) to ensure uniform electrolyte film thickness at reaction conditions. The depletion of the reactant (i.e., ethanol or ethylene glycol in the case of electrocatalytic alcohol oxidation) is decreased by a specifically designed flow-through glassy carbon borehole electrode embedded in PEEK. The electrolyte can be pumped through the disk-shaped gap between the ring working electrode and the IRE into the borehole via an external peristaltic pump. To ensure a radially uniform electrolyte flow, the working electrode and the internal reflection element need to be aligned in parallel at a well-controlled distance, which was achieved by a three-microelectrode-assisted tilt correction. Tilt correction of this four-electrode ensemble and the IRE was performed by three step-motor-driven micrometer screws that allow adjustment of the electrode orientation. The effect of electrolyte pumping through the borehole electrode was analyzed by performing anodic ethanol oxidation using nickel boride as electrocatalyst. The applicability, reliability, and functionality of the cell was further assessed by oxidizing ethylene glycol and determining the reaction products as a function of the electrolyte flow rate. It is found to be essential to induce forced electrolyte convection into the thin electrolyte layer to achieve well-defined steady-state conditions, as mass transport by diffusion is by far insufficient, resulting in reactant depletion, product accumulation, and local pH changes. © 2019 American Chemical Society.

The milling ball is the catalyst. We introduce a palladium-catalyzed reaction inside a ball mill, which makes catalyst powders, ligands, and solvents obsolete. We present a facile and highly sustainable synthesis concept for palladium-catalyzed C−C coupling reactions, exemplarily showcased for the Suzuki polymerization of 4-bromo or 4-iodophenylboronic acid giving poly(para-phenylene). Surprisingly, we observe one of the highest degrees of polymerization (199) reported so far. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

A future widespread application of electrochemical energy conversion and storage technologies strongly depends on the substitution of precious metal-based electrocatalysts for the high-overpotential oxygen reduction and oxygen evolution reactions. We report a novel Co/Co–Fe nanoparticles/N-doped carbon composite electrocatalyst (Co/CoxFey/NC) obtained by pyrolysis of CoFe layered double hydroxide (CoFe LDH) embedded in a film of a bisphenol A and tetraethylenepentamine-based polybenzoxazine poly(BA-tepa). During pyrolysis poly(BA-tepa) forms a highly conductive nitrogen-doped carbon matrix encapsulating Co/Co–Fe nanoparticles, thereby circumventing the need of any additional binder material and conductive additives. Optimization with respect to pyrolysis temperature, the CoFe LDH/BA-tepa ratio, as well as of the gas atmosphere used during the thermal treatment was performed. The optimized Co/CoxFey/NC composite material catalyst exhibits remarkable bifunctional activity towards oxygen reduction (ORR) and oxygen evolution (OER) reactions in 0.1 M KOH represented by a potential difference of only 0.77 V between the potentials at which current densities of −1 mA cm−2 for the ORR and 10 mA cm−2 for the OER were recorded. Moreover, the Co/CoxFey/NC composite material pyrolyzed in ammonia atmosphere exhibits promising stability during both the ORR and the OER. © 2019 Elsevier Ltd

We report the fabrication of a polymer/enzyme-based biosupercapacitor (BSC)/biofuel cell (BFC) hybrid device with an optimized cell voltage that can be switched on demand from energy conversion to energy storage mode. The redox polymer matrices used for the immobilization of the biocatalyst at the bioanode and biocathode act simultaneously as electron relays between the integrated redox enzymes and the electrode surface (BFC) and as pseudocapacitive charge storing elements (BSC). Moreover, owing to the self-charging effect based on the continuously proceeding enzymatic reaction, a Nernstian shift in the pseudocapacitive elements, that is, in the redox polymers, at the individual bioelectrodes leads to a maximized open circuit voltage of the device in both operating modes. Comparison with a conventional fuel cell design, that is, using redox mediators with redox potentials that are close to the potentials of the used redox proteins, indicates that the novel hybrid device shows a similar voltage output. Moreover, our results demonstrate that the conventional design criteria commonly used for the development of redox polymers for the use in biofuel cells have to be extended by considering the effect of a Nernstian shift towards the potentials of the used biocatalysts in those pseudocapacitive elements. © 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Identifying the intrinsic electrocatalytic activity of nanomaterials is challenging, as their characterization usually requires additives and binders whose contributions are difficult to dissect. Herein, we use nano impact electrochemistry as an additive-free method to overcome this problem. Due to the efficient mass transport at individual catalyst nanoparticles, high current densities can be realized. High-resolution bright-field transmission electron microscopy and selected area diffraction studies of the catalyst particles before and after the experiments provide valuable insights in the transformation of the nanomaterials during harsh oxygen evolution reaction (OER) conditions. We demonstrate this for 4 nm sized CoFe2O4 spinel nanoparticles. It is revealed that these particles retain their size and crystal structure even after OER at current densities as high as several kA·m-2. The steady-state current scales with the particle size distribution and is limited by the diffusion of produced oxygen away from the particle. This versatilely applicable method provides new insights into intrinsic nanocatalyst activities, which is key to the efficient development of improved and precious metal-free catalysts for renewable energy technologies. © 2019 American Chemical Society.

An extensive characterization of Co3(PO4)2 was performed by topological analysis according to Bader‘s Quantum Theory of Atoms in Molecules from the experimentally and theoretically determined electron density. This study sheds light on the reactivity of cobalt orthophosphate as a solid-state heterogeneous oxidative-dehydration and -dehydrogenation catalyst. Various faces of the bulk catalyst were identified as possible reactive sites given their topological properties. The charge accumulations and depletions around the two independent five- and sixfold-coordinated cobalt atoms, found in the topological analysis, are correlated to the orientation and population of the d-orbitals. It is shown that the (011) face has the best structural features for catalysis. Fivefold-coordinated ions in close proximity to advantageously oriented vacant coordination sites and electron depletions suit the oxygen lone pairs of the reactant, mainly for chemisorption. This is confirmed both from the multipole refinement as well as from density functional theory calculations. Nearby basic phosphate ions are readily available for C−H activation. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

A series of surfactant-free nickel-core and silver-shell (Ni@Ag) nanoparticles encapsulated within the mesopores of SBA-15 were synthesized and tested as catalysts for direct propylene oxidation by molecular oxygen. The influences of temperature, Gas Hour Space Velocity (GHSV) and Ni/Ag ratio on catalytic activity were systematically investigated. Among the prepared samples, Ni1Ag0.4/SBA-15 exhibited the best catalytic performance with selectivity of 70.7% and PO production rate of 4.4 nmol/g/s under 1 bar at 220 °C with GHSV of 192 h−1. High selectivity was attributed to longer Ag-Ag interatomic distance obtained by careful engineering the thickness of Ag shell over preformed Ni nanoparticles. In addition, all prepared new Ni@Ag core-shell catalysts presented excellent stability, which could maintain the conversion and selectivity for at least 10 h. These results suggest that new designs based on Ag surface atoms tailoring might pave the way to highly efficient and robust Ag catalysts for direct propylene oxidation using molecular oxygen as sole oxidant. © 2018 Elsevier B.V.

Metal-exchanged zeolites with small pore sizes have attracted much attention in recent years due to their application in the selective catalytic reduction (SCR) of NOx in diesel engines. Typically, copper-chabazite (e.g. Cu-SSZ-13) has been gradually used as an SCR catalyst in heavy-duty diesel vehicles over the last decade due to its relatively excellent catalytic performance and stability. However, most SSZ-13 zeolites are still prepared via the traditional hydrothermal process in the presence of organic templates, requiring consecutive solid separation and thermal treatment steps to achieve the final zeolite products. In recent years, several strategies for the environmentally friendly preparation of zeolites have been reported, which are also applicable for the synthesis of zeolites for emission control applications. These concepts include copper-amine templating, organotemplate-free synthesis, and solvent-free synthesis. In this review, we briefly summarize the potential advantages of the environmentally friendly synthesis of zeolites for SCR. © The Royal Society of Chemistry 2019.

The kinetics of glycerol hydrodeoxygenation to 1,2-propanediol via the selective cleavage of the primary C-O bond was systematically studied in the aqueous phase over a co-precipitated Cu/ZrO2 catalyst. Unsupported pure metallic Cu was used as reference catalyst. Batch experiments were performed in an autoclave by varying the reaction temperature (175–225 °C), H2 partial pressure (25–35 bar) and initial glycerol concentration (2–8 wt%). The Cu/ZrO2 catalyst was found to be highly selective to 1,2propanediol (up to 95%), and ethylene glycol was obtained as major by-product from parallel C–]C bond hydrogenolysis. The apparent activation energies amounting to 106 and 105 kJ mol-1 for Cu/ZrO2 and pure metallic Cu, respectively, of the hydrodeoxygenation pathway provide further evidence for metallic Cu acting as the active site. Kinetic analysis of the rate of glycerol consumption yielded a zero-order dependence on the concentration of glycerol suggesting an essentially almost full coverage of adsorbed glycerol as most strongly bound organic adsorbate. In contrast, a first-order dependence on hydrogen concentration was observed. Hydrogen is assumed to be not only required for the fast hydrogenation of the intermediate acetol, but also for the removal of adsorbed atomic oxygen originating from water dissociation to create empty sites for dissociative glycerol adsorption. Thus, the active Cu sites are assumed to be fully adsorbate-covered under reaction conditions. © 2019 Elsevier B.V.

The kinetics of glycerol hydrodeoxygenation to 1,2-propanediol via the selective cleavage of the primary C-O bond was systematically studied in the aqueous phase over a co-precipitated Cu/ZrO 2 catalyst. Unsupported pure metallic Cu was used as reference catalyst. Batch experiments were performed in an autoclave by varying the reaction temperature (175–225 °C), H 2 partial pressure (25–35 bar) and initial glycerol concentration (2–8 wt%). The Cu/ZrO 2 catalyst was found to be highly selective to 1,2propanediol (up to 95%), and ethylene glycol was obtained as major by-product from parallel C–]C bond hydrogenolysis. The apparent activation energies amounting to 106 and 105 kJ mol -1 for Cu/ZrO 2 and pure metallic Cu, respectively, of the hydrodeoxygenation pathway provide further evidence for metallic Cu acting as the active site. Kinetic analysis of the rate of glycerol consumption yielded a zero-order dependence on the concentration of glycerol suggesting an essentially almost full coverage of adsorbed glycerol as most strongly bound organic adsorbate. In contrast, a first-order dependence on hydrogen concentration was observed. Hydrogen is assumed to be not only required for the fast hydrogenation of the intermediate acetol, but also for the removal of adsorbed atomic oxygen originating from water dissociation to create empty sites for dissociative glycerol adsorption. Thus, the active Cu sites are assumed to be fully adsorbate-covered under reaction conditions. © 2019 Elsevier B.V.

Fabrication of efficient and cost-effective bifunctional oxygen electrocatalysts for both the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) remains a challenge for the development of rechargeable metal-air batteries and unitized regenerative fuel cells technologies. Herein, we report high-performance bifunctional ORR/OER electrocatalysts consisting of mixed transition metal (Fe, Co, Ni) oxide nanoparticles supported on oxidized multi-walled carbon nanotubes (MWCNT). Investigation of the ORR and OER activity of samples with different metal compositions showed that trimetallic/MWCNT composites having Fe:Ni:Co = x:x:(1-2x) ratios, with 0.25 ≤ x ≤ 0.4, exhibit highest bifunctional activity in terms of the reversible ORR/OER overvoltage at a given current density. Moreover, the trimetallic catalysts exhibited improved selectivity with respect to the reduction of O 2 to OH − compared to the bimetallic Fe-Ni, Fe-Co and Co-Ni catalysts, thus revealing synergistic interactions among the metal oxide components. Correlation of the electrocatalytic activity with the structure of the composites is discussed for the most representative cases. © 2019 Elsevier B.V.

The impact of individual HAuCl4 nanoreactors is measured electrochemically, which provides operando insights and precise control over the modification of electrodes with functional nanoparticles of well-defined size. Uniformly sized micelles are loaded with a dissolved metal salt. These solution-phase precursor entities are then reduced electrochemically—one by one—to form nanoparticles (NPs). The charge transferred during the reduction of each micelle is measured individually and allows operando sizing of each of the formed nanoparticles. Thus, particles of known number and sizes can be deposited homogenously even on nonplanar electrodes. This is demonstrated for the decoration of cylindrical carbon fibre electrodes with 25±7 nm sized Au particles from HAuCl4-filled micelles. These Au NP-decorated electrodes show great catalyst performance for ORR (oxygen reduction reaction) already at low catalyst loadings. Hence, collisions of individual precursor-filled nanocontainers are presented as a new route to nanoparticle-modified electrodes with high catalyst utilization. © 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Coupling electrochemical generation of hydrogen with the concomitant formation of an industrially valuable product at the anode instead of oxygen can balance the high costs usually associated with water electrolysis. We report the synthesis of a variety of nanoparticulate LaCo1−xFexO3 perovskite materials through a specifically optimized spray-flame nanoparticle synthesis method, using different ratios of La, Co, and Fe precursor compounds. Structural characterization of the resulting materials by XRD, TEM, FTIR, and XPS analysis revealed the formation of mainly perovskite-type materials. The electrocatalytic performance of the formed perovskite-type materials towards the oxygen evolution reaction and the ethanol oxidation reaction was investigated by using rotating disk electrode voltammetry. An increased Fe content in the precursor mixture leads to a decrease in the electrocatalytic activity of the nanoparticles. The selectivity towards alcohol oxidation in alkaline media was assessed by using the ethanol oxidation reaction as a model reaction. Operando electrochemistry/ATR-IR spectroscopy results reveal that acetate and acetaldehyde are the final products, depending on the catalyst composition as well as on the applied potential. © 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Determination of the intrinsic electrocatalytic activity of nanomaterials by means of macroelectrode techniques is compromised by ensemble and film effects. Here, a unique “particle on a stick” approach is used to grow a single metal–organic framework (MOF; ZIF-67) nanoparticle on a nanoelectrode surface which is pyrolyzed to generate a cobalt/nitrogen-doped carbon (CoN/C) composite nanoparticle that exhibits very high catalytic activity towards the oxygen evolution reaction (OER) with a current density of up to 230 mA cm−2 at 1.77 V (vs. RHE), and a high turnover frequency (TOF) of 29.7 s−1 at 540 mV overpotential. Identical location transmission electron microscopy (IL-TEM) analysis substantiates the “self-sacrificial” template nature of the MOF, while post-electrocatalysis studies reveal agglomeration of Co centers within the CoN/C composite during the OER. “Single-entity” electrochemical analysis allows for deriving the intrinsic electrocatalytic activity and furnishes insight into the transient behavior of the electrocatalyst under reaction conditions. © 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Co-Cu-based catalysts are widely applied in higher alcohol synthesis (HAS) from synthesis gas. Although the nature of the active sites is still not fully understood, the formation of Co2C under HAS conditions seems to play a major role. A CO pretreatment procedure was developed allowing a systematic investigation of the influence of cobalt carbidization on the structural properties and catalytic performance of the catalysts. By exposing the catalyst to a CO-containing atmosphere prior to HAS, Co enrichment of the catalyst surface occurred followed by carbide formation. This surface modification decreased the formation of hydrocarbons and enhanced the formation of C2+OH. The catalyst pretreated with CO at 20 bar achieved the highest selectivity to ethanol and the lowest hydrocarbon selectivity. © 2019 Dalian Institute of Chemical Physics, the Chinese Academy of Sciences

We present airbrush spray-coating as a reproducible method for the preparation of Mo-doped BiVO4 (Mo : BiVO4) as photoabsorber with different layer thicknesses and Mo content. Optimisation of layer thickness is aiming on diminishing limitations by the electronic conductivity within the photoabsorber, thus increasing the incident photon to current efficiency (IPCE) of the samples. Furthermore, the Mo to V ratio leading to the highest photocurrent density was determined, and the optimised Mo : BiVO4 samples were decorated with a variety of oxygen evolution reaction (OER) electrocatalysts such as cobalt phosphate and layered double hydroxides. A mass loading gradient of Ni−Fe LDH was sprayed on top of the Mo : BiVO4 photoanode for optimisation of the OER catalyst loading. The photocurrent density was enhanced by up to 5.8 times at 0.8 V vs. RHE in comparison with the pristine Mo : BiVO4 sample in absence of any OER electrocatalyst. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Understanding the fundamentals of iridium degradation during the oxygen evolution reaction is of importance for the development of efficient and durable water electrolysis systems. The degradation mechanism is complex and it is under intense discussion whether the oxygen molecule can be directly released from the oxide lattice. Here, we define the extent of lattice oxygen participation in the oxygen evolution and associated degradation of rutile and hydrous iridium oxide catalysts, and correlate this mechanism with the atomic-scale structures of the catalytic surfaces. We combine isotope labelling with atom probe tomography, online electrochemical and inductively coupled plasma mass spectrometry. Our data reveal that, unlike rutile IrO2, Ir hydrous oxide contains -IrIIIOOH species which directly contribute to the oxygen evolution from the lattice. This oxygen evolution mechanism results in faster degradation and dissolution of Ir. In addition, near surface bulk regions of hydrous oxide are involved in the oxygen catalysis and dissolution, while only the topmost atomic layers of rutile IrO2 participate in both reactions. Overall our data provide a contribution to the fundamental understanding of the exceptional stability of Ir-oxides towards the oxygen evolution reaction. The proposed approach to a quantitative assessment of the degree of lattice oxygen participation in the oxygen evolution reaction can be further applied to other oxide catalyst systems. © 2019 The Royal Society of Chemistry.

Complex solid solution (CSS) nanoparticles were recently discovered as efficient electrocatalysts for a variety of reactions. As one of many advantages, they exhibit the potential to replace noble-metal catalysts with multinary combinations of transition metals because they offer formation of new unique and tailorable active sites of multiple elements located next to each other. This Perspective reports on the current state and on challenges of the (combinatorial) synthesis of multinary nanoparticles and advanced electron microscopy characterization techniques for revealing structure-activity correlations on an atomic scale. We discuss what distinguishes this material class from common catalysts to highlight their potential to act as electrocatalysts and rationalize their nontypical electrochemical behavior. We provide an overview about challenges in synthesis, characterization, and electrochemical evaluation and propose guidelines for future design of CSS catalysts to achieve further progress in this research field, which is still in its infancy. © 2019 American Chemical Society.

The development of bifunctional oxygen electrodes is a key factor for the envisaged application of rechargeable metal-air batteries. In this work, we present a simple procedure based on pyrolysis of polybenzoxazine/metal metalloid nanoparticles composites into efficient bifunctional oxygen reduction and oxygen evolution electrocatalysts. This procedure generates nitrogen-doped carbon with embedded metal metalloid nanoparticles exhibiting high activity towards both, oxygen reduction and oxygen evolution, in 0.1 M KOH with a roundtrip voltage of as low as 0.81 V. Koutecký-Levich analysis coupled with scanning electrochemical microscopy reveals that oxygen is preferentially reduced in a 4e− transfer pathway to hydroxide rather than to hydrogen peroxide. Furthermore, the polybenzoxazine derived carbon matrix allows for stable catalyst fixation on the electrode surface, resulting in unattenuated activity during continuous alternate polarisation between oxygen evolution at 10 mA cm−2 and oxygen reduction at −1.0 mA cm−2. © 2018 Elsevier Ltd

The relatively low hydrothermal stability of Al-rich Cu-SSZ-13 catalysts hinders their practical application in ammonia selective catalytic reduction (NH 3 -SCR) reaction. Rare-earth ions were introduced into the Al-rich SSZ-13 zeolite using an organotemplate-free synthesis prior to the exchange of Cu 2+ ions. Among the rare-earth ions tested (Ce, La, Sm, Y, Yb), Y shows significant enhancement of the hydrothermal stability and NH 3 -SCR activities after severe hydrothermal aging at 800 °C for 16 h when compared with Cu-SSZ-13 without Y. Cu-Y-SSZ-13 catalysts with various amounts of Y were prepared, and it is found that with increasing Y content, the low temperature NO conversions can be improved even after hydrothermal aging. SEM-EDX analysis together with two-dimensional multiple quantum magic-angle-spinning nuclear magnetic resonance ( 23 Na MQ MAS NMR) confirms that the Y ions are successfully incorporated into the ion-exchange sites of the SSZ-13 zeolite. Results from 27 Al MAS, 29 Si MAS NMR, temperature-programmed desorption of ammonia (NH 3 -TPD) and quantitative 1 H MAS NMR indicate that Y can stabilize the framework Al and also preserve the Brønsted acid sites in the Al-rich SSZ-13 zeolite. The hydrogen temperature programmed reduction (H 2 -TPR), ultraviolet-visible-near infrared spectroscopy (UV-vis-NIR) and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) of nitric oxide (NO) or NH 3 adsorption demonstrate that introduction of Y ions causes Cu 2+ ions to preferentially occupy the 6-MR, which has high hydrothermal stability. However, too much of Y may lead to activity loss at both low and high temperatures. The optimized Al-rich Cu-Y-SSZ-13 with 2.8 wt% of copper (Cu) and 1.3 wt% of Y displays almost the same deNO x activities as the conventional organotemplated high silica Cu-SSZ-13 catalyst in a wide reaction temperature window of 150-650 °C after severe hydrothermal treatment. Rare-earth ions could be an effective additive for Cu-SSZ-13 catalysts to further improve their hydrothermal stability for practical applications. © 2019 The Royal Society of Chemistry.

The immobilization, protection, and electrical wiring of sensitive catalysts by specifically designed supporting matrixes are of particular importance for technological relevant applications. Here, we describe the protection of a DuBois-type H2 oxidation catalyst, which was covalently bound to an inert polymer matrix, against molecular O2 by forming blends together with an O2-reducing redox polymer matrix. This matrix simultaneously acts as an electron relay for shuttling electrons between the catalyst and the electrode. © 2019 American Chemical Society.

The immobilization, protection, and electrical wiring of sensitive catalysts by specifically designed supporting matrixes are of particular importance for technological relevant applications. Here, we describe the protection of a DuBois-type H 2 oxidation catalyst, which was covalently bound to an inert polymer matrix, against molecular O 2 by forming blends together with an O 2 -reducing redox polymer matrix. This matrix simultaneously acts as an electron relay for shuttling electrons between the catalyst and the electrode. © 2019 American Chemical Society.

Compounds and alloys of cobalt and nickel with some nonmetals (N, P, S, Se) and metalloids (C, B, C, As and Te) have emerged as very promising noble metal-free pre-catalysts for the oxygen evolution reaction (OER) in alkaline electrolytes. However, the exact role played by the non-metals and metalloids in promoting the OER is not well understood. A holistic understanding of the origin of the OER activity enhancement in these compounds is vital for their exploitation as models to inspire knowledge-guided design of improved OER catalysts. In this review, we elucidate the factors that govern the activity and stability of OER catalysts derived from MX compounds (M=Co or Ni, and X=nonmetal or metalloid), including the impact of surface electronic structure, M : X stoichiometry, material composition, structure and crystallinity, as well as the role of oxoanions on the properties of the electrochemical double layer and interaction energies of the reaction intermediates. Finally, we outline a few perspectives and research directions towards a deeper understanding of the role of the nonmetal and metalloid elements and design of improved OER catalysts. ©2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Supported catalysts are among the most important classes of catalysts. They are typically prepared by wet-chemical methods, such as impregnation or co-precipitation. Here we disclose that dry ball milling of macroscopic metal powder in the presence of a support oxide leads in many cases to supported catalysts with particles in the nanometer size range. Various supports, including TiO2, Al2O3, Fe2O3, and Co3O4, and different metals, such as Au, Pt, Ag, Cu, and Ni, were studied, and for each of the supports and the metals, highly dispersed nanoparticles on supports could be prepared. The supported catalysts were tested in CO oxidation, where they showed activities in the same range as conventionally prepared catalysts. The method thus provides a simple and cost-effective alternative to the conventionally used impregnation methods. © 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

“Single entity” measurements are central for an improved understanding of the function of nanoparticle-based electrocatalysts without interference arising from mass transfer limitations and local changes of educt concentration or the pH value. We report a scanning electrochemical cell microscopy (SECCM) investigation of zeolitic imidazolate framework (ZIF-67)-derived Co−N-doped C composite particles with respect to the oxygen evolution reaction (OER). Surmounting the surface wetting issues as well as the potential drift through the use of a non-interfering Os complex as free-diffusing internal redox potential standard, SECCM could be successfully applied in alkaline media. SECCM mapping reveals activity differences relative to the number of particles in the wetted area of the droplet landing zone. The turnover frequency (TOF) is 0.25 to 1.5 s−1 at potentials between 1.7 and 1.8 V vs. RHE, respectively, based on the number of Co atoms in each particle. Consistent values at locations with varying number of particles demonstrates OER performance devoid of macroscopic film effects. © 2019 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Synthesis of silver nanoparticles (Ag NPs) with state-of-the-art chemical or photo-reduction methods generally takes several steps and requires both reducing agents and stabilizers to obtain NPs with narrow size distribution. Herein, we report a novel method to synthesize Ag NPs rapidly in one step, achieving typical particle sizes in the range from 5 to 15 nm. The synthesis steps only involve three chemicals without any reducing agent: AgNO3 as precursor, polyvinylpyrrolidone (PVP) as stabilizer, and AgCl as photocatalyst. The Ag NPs were supported on carbon and showed excellent performance in thermal catalytic p-nitrophenol reduction and nitrobenzene hydrogenation, and as electrocatalyst for the oxygen reduction reaction. © 2019 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences

Gold nanoparticles supported on reduced TiO2 (110) surfaces are widely used as catalysts for oxidation reactions. Despite extensive studies, the role of oxygen vacancies in such systems remains elusive and is controversially discussed. Combining ab initio molecular dynamics simulations with methods originally developed to describe defects in semiconductor physics we study how the electronic charge originally located at the vacancy modifies the charge on the cluster. Despite differences resulting from the employed level of density functional theory (namely semilocal/GGA, GGA + U, and hybrid functionals), we consistently find that the Au clusters remain either neutral or acquire a positive charge. The intuitively expected electron transfer from the oxygen vacancy to the gold cluster can be safely ruled out. Analyzing these findings, we discuss the role of the oxygen vacancy in the bonding between Au clusters and support and the catalytic activity of the system. © 2019 American Chemical Society.

Development of metal-free carbon-based electrocatalysts for reducing oxygen to water (ORR), preferentially following a 4 electron transfer pathway, is of high importance. We present a two-step synthesis of N-doped carbon-based ORR electrocatalysts by using an efficient thermal treatment of hydrothermally carbonized cellulose in ammonia combining devolatilization, reduction and nitrogen doping. The influence of the synthesis temperature as well as of the ammonia concentration used during the synthesis on the electrocatalytic ORR activity was analyzed using bulk- and surface-sensitive techniques. Correlation of electrocatalytic activity with structural features of the catalysts provided deeper mechanistic understanding and enabled us to optimize the synthesis conditions. The nitrogen-doped metal-free catalyst originating from the treatment in 100 % NH3 at 800 °C achieved a current density of −1 mA cm−2 at 0.83 V vs. RHE positioning it among the most active noble-metal free and biomass-based ORR catalysts reported so far. © 2019 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

The efficient reduction of protons by non-noble metals under mild conditions is a challenge for our modern society. Nature utilises hydrogenases, enzymatic machineries that comprise iron- and nickel- containing active sites, to perform the conversion of protons to hydrogen. We herein report a straightforward synthetic pathway towards well-defined particles of the bio-inspired material FexNi9-xS8, a structural and functional analogue of hydrogenase metal sulfur clusters. Moreover, the potential of pentlandites to serve as photocatalysts for solar-driven H2-production is assessed for the first time. The FexNi9-xS8 materials are visible light responsive (band gaps between 2.02 and 2.49 eV, depending on the pentlandite's Fe:Ni content) and display a conduction band energy close to the thermodynamic potential for proton reduction. Despite the limited driving force, a modest activity for photocatalytic H2 has been observed. Our observations show the potential for the future development of pentlandites as photocatalysts. This work provides a basis to explore powerful synergies between biomimetic chemistry and material design to unlock novel applications in solar energy conversion. © 2019 The Royal Society of Chemistry.

Facet-engineering and the deposition of co-catalysts lead to significant improvement in efficiency of semiconductors in photocatalytic applications. Here, we demonstrate, using the specific example of bismuth-oxy-bromide (BiOBr) particles, that facet-selective, photo-induced reductive or oxidative deposition of co-catalysts onto plate-like semiconductor particles is strongly pH-dependent. High resolution atomic force microscopy and spectroscopy measurements demonstrate that the effect of pH is caused by a reversal of the surface charge of the [001] facets upon increasing pH from 3 to 9 (isoelectric point ≈5), while the side facets become increasingly negatively-charged. We discuss the effect of facet-surface-charge on particle distributions by band-bending, favoring either electron transfer and metal deposition, or hole transfer and metal-oxide deposition. This finding opens up new ways to design highly effective, photocatalytic composite architectures, containing spatially separated catalytic particles of multiple compositions. © 2018 The Royal Society of Chemistry.

The determination of the intrinsic properties of nanomaterials is essential for their optimization as electrocatalysts, however it poses great challenges from the standpoint of analytical tools and methods. Herein, we report a novel methodology that allows for a binder-free investigation of electrocatalyst nanoparticles. The potential-assisted immobilization of a non-noble metal catalyst, i.e., nickel-iron layered double hydroxide (NiFe LDH) nanoparticles, was employed to directly attach small nanoparticle ensembles from a suspension to the surface of etched carbon nanoelectrodes. The dimensions of this type of electrodes allowed for the immobilization of the catalyst material below the picogram scale and resulted in a high resolution towards the faradaic current response. In addition the effect of the electrochemical aging on the intrinsic activity of the catalyst was investigated in alkaline media by means of continuous cyclic voltammetry. A change in the material properties could be observed, which was accompanied by a substantial decrease in its intrinsic activity. [Figure not available: see fulltext.] © 2018, Tsinghua University Press and Springer-Verlag GmbH Germany, part of Springer Nature.

Abstract: A continuously operated flow setup with fixed-bed reactor and online gas analysis enabled kinetic investigations of catalysts for the carbon dioxide reforming of methane under industrially relevant conditions at temperatures up to 1000 °C and at pressures up to 20 bar. A coaxial reactor design consisting of an inner- and an outer highly alloyed steel tube allowed obtaining axial temperature profiles by means of a moveable thermocouple. A NiAl2O4-based catalyst was tested at 820 °C and pressures of 1, 10 or 20 bar and compared to a conventional Ni catalyst used for steam reforming of methane. A significant cold spot was detected even when using only 10 mg of catalysts diluted in 1 g of silicon carbide. The specifically designed NiAl2O4/Al2O3 dry reforming catalyst with a high dispersion of the active Ni0 phase was found to be far superior to the conventional steam reforming catalyst. Graphical Abstract: [Figure not available: see fulltext.] © 2018, Springer Science+Business Media, LLC, part of Springer Nature.

Materials used for photocatalytic overall water splitting (POWS) are typically composed of light-absorbing semiconductor crystals, functionalized with so-called cocatalytic nanoparticles to improve the kinetics of the hydrogen and/or oxygen evolution reactions. While function, quantity, and protection of such metal(oxide) nanoparticles have been addressed in the literature of photocatalysis, the stability and transients in the active oxidation-state upon illumination have received relatively little attention. In this Perspective, the latest insights in the active state of frequently applied cocatalysts systems, including Pt, Rh/Cr2O3, or Ni/NiOx, will be presented. While the initial morphology and oxidation state of such nanoparticles is a strong function of the applied preparation procedure, significant changes in these properties can occur during water splitting. We discuss these changes in relation to the nature of the cocatalyst/semiconductor interface. We also show how know-how of other disciplines such as heterogeneous catalysis or electro-catalysis and recent advances in analytical methodology can help to determine the active state of cocatalytic nanoparticles in photocatalytic applications. © 2018 American Chemical Society.

Pd or Pt alloyed with a secondary metal are the typical catalysts at the anode for the direct oxidation of methanol. The secondary metal is employed to diminish deactivation commonly ascribed to CO poisoning. Here we investigate the origin of the improved performance of Au-Pd core-shell and alloy nanocrystals as electrocatalysts for the methanol oxidation reaction (MOR), relative to Pd alone. Monodisperse Au-Pd core-shell nanocrystals were synthesized using H2 as a mild reducing agent followed by annealing under a 5% H2 atmosphere to produce the Au-Pd alloys. The nanocrystals were characterized using high-resolution electron microscopy to confirm their structures. The core-shell and alloy nanocrystals showed an improvement in specific activity with respect to pure Pd nanocrystals. Importantly, the stability was also improved by the inclusion of Au for both nanocrystals, being 2.7× higher for the alloy than for the core-shell after 30 min, while the activity is completely lost for the Pd nanocrystals within 10 min. We show that there is no evidence of CO formation for any of the Pd-based catalysts in an alkaline environment. The origin of the improvement in terms of both activity and stability results from positive shifts in the PdO formation/reduction potential caused by the presence of Au, which results in more Pd sites available for the MOR. © 2018 American Chemical Society.

Different Ni/ZrO2 catalysts were prepared and tested for the hydrodeoxygenation (HDO) reaction of guaiacol. It was shown that the preparation mode of the ZrO2 support has a significant influence on the catalytic results, as remaining elements like Si and Na from the preparation can change the material properties. The influence of Si and Na onto these material properties, which were especially surface acidity and oxygen vacancy concentration, could be clarified. It could be also rationalized, how the change of these properties affects the results of the HDO reaction. Furthermore, it was demonstrated that the oxygen vacancy concentration is an important factor for the catalytic performance, although this property has hardly been considered in the design of HDO catalysts so far. La doping was found to be an efficient strategy to tune the oxygen vacancy concentration, and by using this approach the catalytic performance of the catalyst could be improved remarkably. © 2018

The dehydrogenation of ethanol to acetaldehyde (DHEA) is an environmentally benign alternative for synthetic chemistry and for the fine chemical industry. The key is to design Cu-based catalysts with certain structures to obtain high acetaldehyde selectivity. Herein, hybrid C@SiO2 hollow submicron spheres were designed and synthesized using a confined pyrolysis method. This hybrid structure processes a layer of carbon-silica hybrid shell. After loading the Cu, the Cu/C@SiO2 catalyst exhibited 36.1% conversion of ethanol and ∼99% acetaldehyde selectivity at 260 °C. The hybrid support combined the two favorable properties of carbon and silica and thus improving both selectivity and stability. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Mössbauerite is investigated for the first time as an “iron-only” mineral for the electrocatalytic oxygen evolution reaction in alkaline media. The synthesis proceeds via intermediate mixed-valence green rust that is rapidly oxidized in situ while conserving the layered double hydroxide structure. The material catalyzes the oxygen evolution reaction on a glassy carbon electrode with a current density of 10 mA cm−2 at 1.63 V versus the reversible hydrogen electrode. Stability measurements, as well as post-electrolysis characterization are presented. This work demonstrates the applicability of iron-only layered double hydroxides as earth-abundant oxygen evolution electrocatalysts. Mössbauerite is of fundamental importance since as an all Fe3+ material its performance has no contributions from unknown synergistic effects as encountered for mixed valence Co/Ni/Fe LDH. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

We report a designed Cu/C/SiO2 composite catalyst, which shows a high acetaldehyde selectivity (up to ∼98%) and good stability for a 60 h test at 260 °C in ethanol dehydrogenation. Various characterization techniques demonstrate that the carbon covers the Si-OH groups on silica and promotes the reduction of Cu+ to Cu0. This reduces the concentration of active sites for secondary reactions of CH3CHO, which leads to a high initial selectivity (∼93%) as compared to that of Cu/SiO2 (∼76%). Moreover, the chemical interaction between Cu and SiO2 of the C/SiO2 support, verified by X-ray photoelectron spectroscopy, enhances the interaction between the metal and the support and thus contributes to prevention of the agglomeration of Cu particles, which is the reason for the good catalytic stability of Cu/C/SiO2. Thus, this study is an example of how careful design of the catalyst can strongly improve the catalytic performance. © 2018 The Royal Society of Chemistry.

The design of non-noble metal-containing heterogeneous catalysts for the activation of small molecules is of utmost importance for our society. While nature possesses very sophisticated machineries to perform such conversions, rationally designed catalytic materials are rare. Herein, we aim to raise the awareness of the overall common design and working principles of catalysts incorporating aspects of biology, chemistry, and material sciences. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

2D layered materials, including metal-di-chalcogenides and transition metal layered double hydroxides, among others, are intensively studied because of new properties that emerge from their 2D confinement, which are attractive for advanced applications. Herein, 2D cobalt ion (Co2+) and benzimidazole (bIm) based zeolite-imidazole framework nanosheets, ZIF-9(III), are reported as exceptionally efficient electrocatalysts for the oxygen evolution reaction (OER). Specifically, liquid-phase ultrasonication is applied to exfoliate a [Co4(bIm)16] zeolite-imidazole framework (ZIF), named as ZIF-9(III) phase, into nanoscale sheets. ZIF-9(III) is selectively prepared through simple mechanical grinding of cobalt nitrate and benzimidazole in the presence of a small amount of ethanol. The resultant exfoliated nanosheets exhibit significantly higher OER activity in alkaline conditions than the corresponding bulk phases ZIF-9 and ZIF-9(III). The electrochemical and physicochemical characterization data support the assignment of the OER activity of the exfoliated nanosheet derived material to nitrogen coordinated cobalt oxyhydroxide N4CoOOH sites, following a mechanism known for Co-porphyrin and related systems. Thus, exfoliated 2D nanosheets hold promise as potential alternatives to commercial noble metal electrocatalysts for the OER. © 2018 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Surface segregation, restructuring, and sintering phenomena in size-selected copper-nickel nanoparticles (NPs) supported on silicon dioxide substrates were systematically investigated as a function of temperature, chemical state, and reactive gas environment. Using near-ambient pressure (NAP-XPS) and ultrahigh vacuum X-ray photoelectron spectroscopy (XPS), we showed that nickel tends to segregate to the surface of the NPs at elevated temperatures in oxygen- or hydrogen-containing atmospheres. It was found that the NP pretreatment, gaseous environment, and oxide formation free energy are the main driving forces of the restructuring and segregation trends observed, overshadowing the role of the surface free energy. The depth profile of the elemental composition of the particles was determined under operando CO2 hydrogenation conditions by varying the energy of the X-ray beam. The temperature dependence of the chemical state of the two metals was systematically studied, revealing the high stability of nickel oxides on the NPs and the important role of high valence oxidation states in the segregation behavior. Atomic force microscopy (AFM) studies revealed a remarkable stability of the NPs against sintering at temperatures as high as 700 °C. The results provide new insights into the complex interplay of the various factors which affect alloy formation and segregation phenomena in bimetallic NP systems, often in ways different from those previously known for their bulk counterparts. This leads to new routes for tuning the surface composition of nanocatalysts, for example, through plasma and annealing pretreatments. © 2017 American Chemical Society.

Reducing the noble metal loading and increasing the specific activity of the oxygen evolution catalysts are omnipresent challenges in proton-exchange-membrane water electrolysis, which have recently been tackled by utilizing mixed oxides of noble and non-noble elements. However, proper verification of the stability of these materials is still pending. Here we introduce a metric to explore the dissolution processes of various iridium-based oxides, defined as the ratio between the amounts of evolved oxygen and dissolved iridium. The so-called stability number is independent of loading, surface area or involved active sites and provides a reasonable comparison of diverse materials with respect to stability. The case study on iridium-based perovskites shows that leaching of the non-noble elements in mixed oxides leads to the formation of highly active amorphous iridium oxide, the instability of which is explained by the generation of short-lived vacancies that favour dissolution. These insights are meant to guide further research, which should be devoted to increasing the utilization of highly durable pure crystalline iridium oxide and finding solutions to stabilize amorphous iridium oxides. © 2018 The Author(s).

Tungsten carbide has attracted much interest as possible support for oxygen reduction and hydrogen oxidation in fuel cells and as catalyst itself for the hydrogen evolution reaction in water electrolyzers in the last years. Herein, we investigate the dissolution behavior of hexagonal tungsten carbide in acidic media with cyclovoltammetric and galvanostatic procedures under steady-state and dynamic conditions. The tungsten dissolution rate in the electrolyte was monitored in-situ and time resolved via coupling of the scanning flow cell with an inductively coupled plasma mass spectrometer (SFC-ICP-MS), allowing a direct correlation of potential and amount of dissolved species. The stability and passivation behavior of tungsten carbide was compared to pristine tungsten metal and its highest oxide WO3 in fuel cell/electrolyzer relevant potential ranges. It was found that partial passivation in the oxygen reduction region takes place, accompanied by steady dissolution of tungsten slightly above these potentials. In the HER/HOR region, no significant dissolution was observed. The dissolution rate of WC at high potentials was found to be in many cases almost one order of magnitude lower than for the pristine metal, yet two orders of magnitude higher than for its corresponding highest oxide. © 2018 Elsevier Ltd

The topmost atomic layers of electrocatalysts determine the mechanism and kinetics of reactions in many important industrial processes, such as water splitting, chlor-electrolysis or fuel cells. Optimizing the performance of electrocatalysts requires a detailed understanding of surface-state changes during the catalytic process, ideally at the atomic scale. Here, we use atom probe tomography to reveal the three-dimensional structure of the first few atomic layers of electrochemically grown iridium oxide, an efficient electrocatalyst for the oxygen evolution reaction. We unveil the formation of confined, non-stoichiometric Ir-O species during oxygen evolution. These species gradually transform to IrO2, providing improved stability but also a decrease in activity. Additionally, electrochemical growth of oxide in deuterated solutions allowed us to trace hydroxy-groups and water molecules present in the regions of the oxide layer that are favourable for the oxygen evolution and iridium dissolution reactions. Overall, we demonstrate how tomography with near-atomic resolution advances the understanding of complex relationships between surface structure, surface state and function in electrocatalysis. © 2018 The Author(s).

By a combination of electron paramagnetic resonance spectroscopy, finite-temperature ab initio simulations, and electronic structure analyses, the activation of molecular dioxygen at the interface of gold nanoparticles and titania in Au/TiO2 catalysts is explained at the atomic scale by tracing processes down to the molecular orbital picture. Direct evidence is provided that excess electrons in TiO2, for example created by photoexcitation of the semiconductor, migrate to the gold particles and from there to oxygen molecules adsorbed at gold/titania perimeter sites. Superoxide species are formed more efficiently in this way than on the bare TiO2 surface. This catalytic effect of the gold nanoparticles is attributed to a weakening of the internal O-O bond, leading to a preferential splitting of the molecule at shorter bond lengths together with a 70% decrease of the dissociation free energy barrier compared to the non-catalyzed case on bare TiO2. The findings are an important step forward in the clarification of the role of gold in (photo)catalytic processes. © 2018 American Chemical Society.

The performance of electrolyzers for hydrogen production is strongly influenced by electrolyte impurities having either a positive or negative impact on the activity of electrocatalysts. We show that cathode deactivation by zinc impurities present in the electrolyte can be overcome by employing catalyst immobilization based on self-assembled and self-healing films. During electrolysis zinc impurities deposit as dendritic films on the cathode electrode increasing the overpotential for the hydrogen evolution reaction (HER), however, continuous self-assembling and self-healing of HER catalyst films subsequently mask the zinc dendrites restoring the advantageous HER overpotential. Zn electrolyte impurities are turned from having a negative to a positive impact leading to an enhanced performance of the cathode due to the increase in surface area caused by the growth of the Zn dendrites. © 2018 Elsevier Ltd

Spillover hydrogen species were generated by dissociative H2 adsorption on Pt nanoparticles supported on nitrogen-doped mesoporous carbon. The spillover hydrogen species on the support can migrate back to the Pt nanoparticles and hydrogenate subsequently adsorbed nitrobenzene to aniline at 80 °C, which was detected during temperature-programmed desorption experiments from 80 to 300 °C in pure He. The amount of spillover hydrogen can be tuned mainly by the pre-reduction temperature rather than by other parameters. The absence of aniline formation during nitrobenzene desorption experiments in the presence of CO indicates that hydrogenation occurs exclusively on Pt and that the spillover hydrogen species are present on the carbon support in a chemically inactive state. Most likely, spillover hydrogen is reversibly stored on the carbon support as adsorbed protons on the surface and as electrons in the bulk. These findings provide a new perspective on Pt/C-based hydrogen storage materials and fuel cell catalysts. © 2018

A facile strategy is reported for the synthesis of Fe/Co mixed metal oxide nanoparticles supported on, and embedded inside, high purity oxidized multiwalled carbon nanotubes (MWCNTs) of narrow diameter distribution as effective bifunctional catalysts able to reversibly drive the oxygen evolution reaction (OER) and the oxygen reduction reaction (ORR) in alkaline solutions. Variation of the Fe/Co ratio resulted in a pronounced trend in the bifunctional ORR/OER activity. Controlled synthesis and in-depth characterization enabled the identification of an optimal Fe/Co composition, which afforded a low OER/OER reversible overvoltage of only 0.831 V, taking the OER at 10 mA cm−2 and the ORR at −1 mA cm−2. Importantly, the optimal catalyst with a Fe/Co ratio of 2:3 exhibited very promising long-term stability with no evident change in the potential for both the ORR and the OER after 400 charge/discharge (OER/ORR) cycles at 15 mA cm−2 in 6 m KOH. Moreover, detailed investigation of the structure, size, and phase composition of the mixed Fe/Co oxide nanoparticles, as well as their localization (inside of or on the surface of the MWCNTs) revealed insight of the possible contribution of the individual catalyst components and their synergistic interaction in the catalysis. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

An improved general understanding of electrocatalytic gas evolution reactions may - besides contributing to fundamental knowledge - play a crucial role in efforts directed to energy savings during large-scale industrial electrocatalytic processes. Aside from the search for new electrocatalytically active materials, in-depth understanding of electrode surface properties may contribute to more efficient utilization of known electrocatalysts. SECM is applied in the sample generation/tip collection mode to determine the spatial distribution of electrocatalytic activity during Cl2 evolution at the solid/liquid interface of dimensionally stable anodes. Statistical interpretation of the local microscopic distribution of the electrocatalytic activity of dimensionally stable anodes was used as a basis for improved understanding of their overall electrocatalytic performance. © 2018

The design of efficient oxygen electrocatalysts is extremely important and urgent for much energy storage and conversion equipment. Among these, the high energy densities of lithium-oxygen batteries (LOBs) have driven us to explore bifunctional catalysts. Compared with non-aqueous LOBs, which have been blamed for poor cycling stability due to their undesirable side reaction, hybrid LOBs have been considered an alternative solution due to their high electrochemical reversibility and safeness. Here, one-dimensional hierarchical mesoporous/macroporous LaMn0.7Co0.3O3-x nanotubes were synthesized through an electrospinning method combined with an annealing treatment. With the suitable heat treatment and rational doping with elemental Co, the LMCO-800 sample shows a well-designed hierarchical porous nanotube structure and possess great bifunctional electrocatalytic performance. The linear sweep voltammetry (LSV) curves show that the half-wave potential (E1/2) of the LMCO-800 sample is 0.72 V (vs. RHE) and the average electron transfer number (n) is calculated to be 3.8. Moreover, the successful doping of elemental Co into the LMCO-800 nanotubes can shorten the average distance of the Mn-Mn atoms and promote the formation of O-O bonds, contributing to the enhanced OER performance. The high specific surface area and one-dimensional nanotubes can greatly benefit oxygen diffusion, facilitate electrolyte infiltration and improve electron transfer. Consequently, the as-assembled hybrid lithium-oxygen batteries with an LMCO-800 cathode exhibit superior cycling stability. © 2018 The Royal Society of Chemistry.

The electrochemical oxidation of the biorefinery product 5-(hydroxymethyl)furfural (HMF) to 2,5-furandicarboxylic acid (FDCA), an important platform chemical for the polymer industry, is receiving increasing interest. FDCA-based polymers such as polyethylene 2,5-furandicarboxylate (PEF) are sustainable candidates for replacing polyethylene terephthalate (PET). Herein, we report the highly efficient electrocatalytic oxidation of HMF to FDCA, using Ni foam modified with high-surface-area nickel boride (NixB) as the electrode. Constant potential electrolysis in combination with HPLC revealed a high faradaic efficiency of close to 100 % towards the production of FDCA with a yield of 98.5 %. Operando electrochemistry coupled to ATR-IR spectroscopy indicated that HMF is oxidized preferentially via 5-hydroxymethyl-2-furancarboxylic acid rather than via 2,5-diformylfuran, which is in agreement with HPLC results. This study not only reports a low-cost active electrocatalyst material for the electrochemical oxidation of HMF to FDCA, but additionally provides insight into the reaction pathway. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

A copper(I) 3,5-diphenyltriazolate metal–organic framework (CuTz-1) was synthesized and extensively characterized by using a multi-technique approach. The combined results provided solid evidence that CuTz-1 features an unprecedented Cu5tz6 cluster as the secondary building unit (SBU) with channels approximately 8.3 Å in diameter. This metal–organic framework (MOF) material, which is both thermally and chemically (basic and acidic) stable, exhibited semiconductivity and high photocatalytic activity towards the degradation of dyes in the presence of H2O2. Its catalytic performance was superior to that of reported MOFs and comparable to some composites, which has been attributed to its high efficiency in generating .OH, the most active species for the degradation of dyes. It is suggested that the photogenerated holes are trapped by CuI, which yields CuII, the latter of which behaves as a catalyst for a Fenton-like reaction to produce an excess amount of .OH in addition to that formed through the scavenging of photogenerated electrons by H2O2. Furthermore, it was shown that a dye mixture (methyl orange, methyl blue, methylene blue, and rhodamine B) could be totally decolorized by using CuTz-1 as a photocatalyst in the presence of H2O2 under the irradiation of a Xe lamp or natural sunlight. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

A series of Cu/ZrO2 catalysts with nominal CuO loadings of 5, 10, 18 and 31 wt.% was synthesized by co-precipitation, characterized and applied in the hydrodeoxygenation of glycerol under mild reaction conditions (200 °C, 25 bar H2). These catalysts were highly selective for the cleavage of C−O bonds while preserving C−C bonds leading to 95 % selectivity to 1,2-propanediol. The conversion of glycerol was observed to be linearly correlated with the specific copper surface area derived from N2O frontal chromatography. The reaction was found to occur through the dehydration of glycerol to acetol followed by its hydrogenation to 1,2-propanediol. Metallic copper was identified as the active site for both reactions suggesting the acid ZrO2 sites to be blocked by water. Reusability studies showed that the catalyst was relatively stable and the conversion decreased by only 18 % after three cycles. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

In order to design more powerful electrocatalysts, developing our understanding of the role of the surface structure and composition of widely abundant bulk materials is crucial. This is particularly true in the search for alternative hydrogen evolution reaction (HER) catalysts to replace platinum. We report scanning electrochemical cell microscopy (SECCM) measurements of the (111)-crystal planes of Fe4.5Ni4.5S8, a highly active HER catalyst. In combination with structural characterization methods, we show that this technique can reveal differences in activity arising from even the slightest compositional changes. By probing electrochemical properties at the nanoscale, in conjunction with complementary structural information, novel design principles are revealed for application to rational material synthesis. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

In the endeavor of discovering new noble metal–free electrocatalysts for the oxygen reduction reaction, noble metal–free multinary transition metal nanoparticle libraries are investigated. The complexity of such multiple principal element alloys provides access to a large variety of different elemental compositions, each with potentially unique properties. The strategy for efficient identification of novel electrocatalytically active systems comprises combinatorial co-sputtering into an ionic liquid followed by potential-assisted immobilization of the formed nanoparticles at a microelectrode which allows the evaluation of their intrinsic electrocatalytic activity in alkaline media. A surprisingly high intrinsic activity is found for the system Cr–Mn–Fe–Co–Ni, which is at least comparable to Pt under the same conditions, an unexpected result based on the typical properties of its constituents. Systematic removal of each element from the quinary alloy system yields a significant drop in activity for all quaternary alloys, indicating the importance of the synergistic combination of all five elements, likely due to formation of a single solid solution phase with altered properties which enables the limitations of the single elements to be overcome. Multinary transition metal alloys as a novel material class in electrocatalysis with basically unlimited possibilities for catalyst design, targeting the replacement of noble metal–based materials, are suggested. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Inspired by our recent finding that Fe4.5Ni4.5S8 rock is a highly active electrocatalyst for HER, we set out to explore the influence of the Fe:Ni ratio on the performance of the catalyst. We herein describe the synthesis of (FexNi1-x)9S8 (x = 0-1) along with a detailed elemental composition analysis. Furthermore, using linear sweep voltammetry, we show that the increase in the iron or nickel content, respectively, lowers the activity of the electrocatalyst toward HER. Electrochemical surface area analysis (ECSA) clearly indicates the highest amount of active sites for a Fe:Ni ratio of 1:1 on the electrode surface pointing at an altered surface composition of iron and nickel for the other materials. Specific metal-metal interactions seem to be of key importance for the high electrocatalytic HER activity, which is supported by DFT calculations of several surface structures using the surface energy as a descriptor of catalytic activity. In addition, we show that a temperature increase leads to a significant decrease of the overpotential and gain in HER activity. Thus, we showcase the necessity to investigate the material structure, composition and reaction conditions when evaluating electrocatalysts. © 2017 American Chemical Society.

In Cu-zeolite based selective catalytic reduction of NOx with NH3 (NH3-SCR), Cu species (in particular CuI) solvated by NH3 molecules are predicted theoretically to be highly mobile with their mobility being decisive for the NH3-SCR reactivity at low temperatures (<250 °C). Direct experimental observation of the Cu mobility after NH3 solvation, however, has not been achieved yet. Here we show that complex impedance-based modulus spectroscopy, performed by following the corresponding dielectric relaxation processes at high frequencies (104 to 106 Hz), can be applied to monitor directly the dynamic local movement of Cu ions in zeolite catalysts under NH3-SCR related reaction conditions. Simultaneous in situ impedance and infrared spectroscopy studies, assisted by periodic DFT calculations with reliable van der Waals dispersion corrections, allowed us to identify the key factors determining the local dynamics of Cu ions in two representative Cu-zeolites, i.e. Cu-ZSM-5 and Cu-SAPO-34. The co-adsorption and interaction of NO and NH3 on CuII sites led to the formation of highly mobile CuI species and NH4+ intermediates, and, consequently, significantly enhanced local dynamics of Cu ions in both zeolite catalysts. The re-oxidation of CuI, which is the rate-determining step of NH3-SCR reaction, was more favorable in Cu-SAPO-34 than in Cu-ZSM-5, which can be attributed to the close coupling of NH4+ intermediate and Cu site promoting the formation of CuII-NO2/NH4+. As a result, the overall local dynamics of Cu, largely determined by CuI species, is less dependent on the NH4+ intermediate in Cu-SAPO-34 than in Cu-ZSM-5. © 2018 Elsevier B.V.

In this study, evidence is provided that isolated surface vanadia (VO4) species on SiO2 can similarly act as a thermal heterogeneous catalyst and as a heterogeneous photocatalyst. Structurally identical surface VO4 species catalyze the selective oxidation of methanol both by thermal activation and by UV-light induction. Selectivity to formaldehyde appears to be unity. For the photocatalytic reaction at room temperature, formaldehyde desorption is rate limiting. With larger agglomerates or V2O5 nanoparticles, on the contrary, only the thermal reaction is feasible. This is tentatively attributed to the different positions of electronic states (HOMO/LUMO, valence/conduction band) on the electrochemical energy scale owing to the quantum size effect. Besides providing new fundamental insight into the mode of action of nanosized photocatalysts, our results demonstrate that tuning the photocatalytic reactivity of supported transition-metal oxides by adjusting the degree of agglomeration is feasible. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

SrTiO3 is a well-known photocatalyst inducing overall water splitting when exposed to UV irradiation of wavelengths <370 nm. However, the apparent quantum efficiency of SrTiO3 is typically low, even when functionalized with nanoparticles of Pt or Ni@NiO. Here, we introduce a simple solid-state preparation method to control the incorporation of magnesium into the perovskite structure of SrTiO3. After deposition of Pt or Ni@NiO, the photocatalytic water-splitting efficiency of the Mg:SrTiOx composites is up to 20 times higher compared to SrTiO3 containing similar catalytic nanoparticles, and an apparent quantum yield (AQY) of 10 % can be obtained in the wavelength range of 300–400 nm. Detailed characterization of the Mg:SrTiOx composites revealed that Mg is likely substituting the tetravalent Ti ion, leading to a favorable surface–space–charge layer. This originates from tuning of the donor density in the cubic SrTiO3 structure by Mg incorporation and enables high oxygen-evolution rates. Nevertheless, interfacing with an appropriate hydrogen evolution catalyst is mandatory and non-trivial to obtain high-performance in water splitting. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Cobalt oxide nanoparticles were deposited on nitrogen-doped carbon nanotubes (NCNTs) through impregnation by using cobalt nitrate as a precursor and subsequent drying and calcination. Co loadings were prepared in the range from 4 to 40 wt%, and hydrogen and ammonia were applied in the thermal post-treatment of the CoOx/NCNT samples. The Co3O4 spinel structure was detected in all samples, while the thermal treatment in ammonia and hydrogen led to the formation of CoO and metallic Co in addition. Treatment in ammonia resulted in the partial reduction of Co3O4 to CoO and nitrogen doping of the oxides, leading to excellent electrocatalytic activity in the oxygen evolution reaction (OER) and stability despite of the lower Co oxidation states compared with the sample calcined in air. In contrast, the sample reduced in hydrogen showed a lower activity and stability in the OER. The high activity of the ammonia-treated sample can be assigned to improved conductivity, favorable surface properties with surface nitrogen improving the hydrophilicity of the catalysts, and the more facile transformation to the OER-active layered cobalt oxyhydroxide phase under anodic conditions. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Synthetic pentlandite (Fe4.5Ni4.5S8) is a promising electrocatalyst for hydrogen evolution, demonstrating high current densities, low overpotential, and remarkable stability in bulk form. The depletion of sulfur from the surface of this catalyst during the electrochemical reaction has been proposed to be beneficial for its catalytic performance, but the role of sulfur vacancies and the mechanism determining the reaction kinetics are still unknown. We have performed electrochemical operando studies of the vibrational dynamics of pentlandite under hydrogen evolution reaction conditions using 57Fe nuclear resonant inelastic X-ray scattering. Comparing the measured Fe partial vibrational density of states with density functional theory calculations, we have demonstrated that hydrogen atoms preferentially occupy substitutional positions replacing pre-existing sulfur vacancies. Once all vacancies are filled, the protonation proceeds interstitially, which slows down the reaction. Our results highlight the beneficial role of sulfur vacancies in the electrocatalytic performance of pentlandite and give insights into the hydrogen adsorption mechanism during the reaction. © 2017 American Chemical Society.

SAPO-11 nanosheets with partially filled micropores (N-SAPO-11) and a thickness of 10-20 nm were synthesized using polyhexamethylene biguanide hydrochloride (PHMB) as a mesoporogen and di-n-propylamine (DPA) as a microporous template. After Pt loading (0.5 wt%), the Pt/N-SAPO-11 catalyst exhibits higher selectivity for the isomers and lower selectivity for cracking products than conventional Pt/SAPO-11 catalysts in the hydroisomerization of n-dodecane. © 2017 The Royal Society of Chemistry.

The catalytic hydrogenation of ethyl acetate to ethanol was studied at ambient pressure in the temperature range from 463 K to 513 K using Cu/ZrO2 catalysts obtained by co-precipitation as a function of the Cu loading. The hydrogenation was established as a reproducible probe reaction by determining optimal reaction parameters without deactivation or thermodynamic limitations. Power-law kinetics were determined yielding an apparent activation energy of 74 kJ mol−1 and reaction orders of 0.1–0.3 for H2 and −0.4 to 0.1 for ethyl acetate in the temperature range from 473 K to 503 K. Metallic Cu was found to be essential for the hydrogenation, but the catalytic activity was not proportional to the Cu surface area derived from N2O decomposition and temperature-programmed H2 desorption experiments identifying Cu/ZrO2 as bifunctional catalyst. The acidic sites of the ZrO2 matrix were probed by temperature-programmed experiments with ethyl acetate and NH3. Cu0 is assumed to provide atomic hydrogen by dissociative adsorption and spillover, but the reaction rate is more affected by the tight contact between the embedded Cu nanoparticles and the X-ray amorphous ZrO2 matrix. © 2017 Elsevier Inc.

The implementation of electrochemical systems such as fuel cells has been hindered by the slow development of low cost high activity catalysts. Here we examine the oxygen reduction reaction performance of a combinatorial Pd-Au-Ag-Ti thin film library using high-throughput screening and correlate the electrochemical behavior to the crystallographic properties. We find compositions of ca. 40-60 at% Pd and 30-35 at% Au exhibit both a low overpotential of close to the value of pure Pt as well as high current density. We also observe a volcano-like relationship between the overpotential and the solid formation strain. This study provides compositional guidance towards the future synthesis of nanostructured quaternary Pd-Au-Ag-Ti alloys and suggests the potential for broader application of high-throughput electrochemical characterization by means of an automatic scanning droplet cell. © The Royal Society of Chemistry.

Transients in the composition of Ni@NiOx core-shell co-catalysts deposited on SrTiO3 are discussed on the basis of state-of-the-art continuous analysis of photocatalytic water splitting, and post-XPS and TEM analyses. The formation of excessive hydrogen (H2:O2 ≫ 2) in the initial stages of illumination demonstrates oxidation of Ni(OH)2 to NiOOH (nickel oxyhydroxide), with the latter catalyzing water oxidation. A disproportionation reaction of Ni and NiOOH, yielding Ni(OH)2 with residual embedded Ni, occurs when illumination is discontinued, which explains repetitive transients in (excess) hydrogen and oxygen formation when illumination is reinitiated. (Chemical Equation Presented). © 2017 American Chemical Society.

During application, electrocatalysts are exposed to harsh electrochemical conditions, which can induce degradation. This work addresses the degradation of AuPd bimetallic catalysts used for the electrocatalytic production of hydrogen peroxide (H2O2) by the oxygen reduction reaction (ORR). Potential-dependent changes in the AuPd surface composition occur because the two metals have different dissolution onset potentials, resulting in catalyst dealloying. Using a scanning flow cell (SFC) with an inductively coupled plasma mass spectrometer (ICP-MS), simultaneous Pd and/or Au dissolution can be observed. Thereafter, three accelerated degradation protocols (ADPs), simulating different dissolution regimes, are employed to study the catalyst structure degradation on the nanoscale with identical location (IL) TEM. When only Pd or both Au and Pd dissolve, the composition changes rapidly and the surface becomes enriched with Au, as observed by cyclic voltammetry and elemental mapping. Such changes are mirrored by the evolution of electrocatalytic performances toward H2O2 production. Our experimental findings are finally summarized in a dissolution/structure/selectivity mechanism, providing a clear picture of the degradation of bimetallic catalyst used for H2O2 synthesis. © 2017 American Chemical Society.

Carbon dioxide electroreduction to chemicals and fuels powered by renewable energy sources is considered a promising path to address climate change and energy storage needs. We have developed highly active and selective copper (Cu) nanocube catalysts with tunable Cu(100) facet and oxygen/chlorine ion content by low-pressure plasma pretreatments. These catalysts display lower overpotentials and higher ethylene, ethanol, and n-propanol selectivity, resulting in a maximum Faradaic efficiency (FE) of ∼73% for C2 and C3 products. Scanning electron microscopy and energy-dispersive X-ray spectroscopy in combination with quasi-in situ X-ray photoelectron spectroscopy revealed that the catalyst shape, ion content, and ion stability under electrochemical reaction conditions can be systematically tuned through plasma treatments. Our results demonstrate that the presence of oxygen species in surface and subsurface regions of the nanocube catalysts is key for achieving high activity and hydrocarbon/alcohol selectivity, even more important than the presence of Cu(100) facets. © 2017 American Chemical Society.

We investigate monocrystalline InAs nanowires (NWs) which are grown catalyst assisted by molecular beam epitaxy (MBE) and create the catalyst by focused ion beam (FIB) implanted Au spots. With this combination of methods an aspect ratio, i.e. the length to width ratio, of the grown NWs up to 300 was achieved. To control the morphology and crystalline structure of the NWs, the growth parameters like temperature, flux ratios and implantation fluence are varied and optimized. Furthermore, the influence of the used molecular arsenic species, in particular the As2 to As4 ratio, is investigated and adjusted. In addition to the high aspect ratio, this optimization results in the growth of monocrystalline InAs NWs with a negligible number of stacking faults. Single NWs were placed site-controlled by FIB implantation, which supplements the working field of area growth. © 2017

Au/Mg(OH)2 catalysts have been reported to be far more active in the catalytic low-temperature CO oxidation (below 0 °C) than the thoroughly investigated Au/TiO2 catalysts. Based on kinetic and in situ infrared spectroscopy (DRIFTS) measurements, we demonstrate that the comparatively weak interaction of Au/Mg(OH)2 with CO2 formed during the low-temperature reaction is the main reason for the superior catalyst performance. This feature enables rapid product desorption and hence continuous CO oxidation at temperatures well below 0 °C. At these temperatures, Au/TiO2 also catalyzes CO2 formation, but does not allow for CO2 desorption, which results in self-poisoning. At higher temperatures (above 0 °C), however, CO2 formation is rate-limiting, which results in a much higher activity for Au/TiO2 under these reaction conditions. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

New catalysts are needed to achieve lower overpotentials and higher faradaic efficiency for desirable products during the electroreduction of CO2. In this study, we explore the size-dependence of monodisperse gold-copper alloy nanoparticles (NPs) synthesized by inverse micelle encapsulation as catalysts for CO2 electroreduction. X-ray spectroscopy revealed that gold-copper alloys were formed and were heavily oxidized in their initial as prepared state. Current density was found to increase significantly for smaller NPs due to the increasing population of strongly binding low coordinated sites on NPs below 5nm. Product analysis showed formation of H2, CO, and CH4, with faradaic selectivity showing a minor dependence on size. The selectivity trends observed are assigned to reaction-induced segregation of gold atoms to the particle surface and altered electronic or geometric properties due to alloying. © 2016.

Aiming at a better understanding of the unusual low-temperature CO oxidation reaction behavior on Au/Mg(OH)2 catalysts, we investigated this reaction mainly by combined kinetic and in situ IR spectroscopy measurements over a wide range of temperatures, from -90 °C to 200 °C. Catalysts with a very narrow Au particle size distribution were prepared by colloidal deposition. Kinetic measurements, performed under differential, dry reaction conditions at different constant temperatures, enabled the separation of thermal and deactivation effects. They revealed that the distinct reaction behavior, with an exceptionally high activity at temperatures below 0 °C and decreasing CO oxidation rates in the range between -50 °C and 30 °C, equivalent to a negative apparent activation energy, does not result from either deactivation effects or H2O trace impurities, but is an intrinsic feature of the reaction. An unusual temperature dependence was also observed for the tendency for deactivation, with a pronounced maximum at -20 °C, which mainly results from an accumulation of surface carbonate species blocking active reaction sites or access of adsorbed reactants to them. Similar measurements on Au/TiO2 catalysts revealed that the high activity of Au/Mg(OH)2 in the low-temperature range compared to Au/TiO2 is first of all due to the weaker interactions of Mg(OH)2 with CO2 compared to TiO2. This leads to an increasing tendency of CO2 product molecules to adsorb on the latter catalyst at reaction temperatures below 0 °C and hence to rapid 'self-poisoning' with CO2 desorption as the rate-limiting step. For Au/Mg(OH)2, CO2 desorption is much faster, allowing much higher rates in the continuous CO oxidation. Based on temporal analysis of products (TAP) reactor measurements, the decay of the reaction rates in the range -50 °C to +50 °C is tentatively attributed to a decreasing steady-state coverage of weakly bound molecularly adsorbed O2 with increasing temperature, while stable adsorbed active surface oxygen is negligible over the entire range of reaction temperatures investigated. The implications of these and earlier findings for the mechanistic understanding of the low-temperature CO oxidation on Au/Mg(OH)2 and support effects therein are discussed. © The Royal Society of Chemistry 2017.

High-throughput characterization by soft X-ray absorption spectroscopy (XAS) and electrochemical characterization is used to establish a correlation between electronic structure and catalytic activity of oxygen evolution reaction (OER) catalysts. As a model system a quasi-ternary materials library of Ni 1-y-zFe y Cr z O x was synthesized by combinatorial reactive magnetron sputtering, characterized by XAS, and an automated scanning droplet cell. The presence of Cr was found to increase the OER activity in the investigated compositional range. The electronic structure of Ni II and Cr III remains unchanged over the investigated composition spread. At the Fe L-edge a linear combination of two spectra was observed. These spectra were assigned to Fe III in O h symmetry and Fe III in T d symmetry. The ratio of Fe III O h to Fe III T d increases with the amount of Cr and a correlation between the presence of the Fe III O h and a high OER activity is found.

A plate reactor was designed to investigate the catalytic soot oxidation applying glass ceramic plates coated with lithium zirconate. The results are compared to the corresponding powder catalysts in thermogravimetric experiments. The deposition of soot by spray coating resulted in an intimate contact mode equivalent to the mortaring preparation of the tight contact powder samples. In the presence of lithium ions the soot oxidation temperature was decreased significantly both in the thermobalance and in the plate reactor. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

As a sustainable pathway for energy storage and to close the carbon cycle, CO2 electroreduction has recently gained significant interest. We report here the role of the electrolyte, in particular of halide ions, on CO2 electroreduction over plasma-oxidized polycrystalline Cu foils. It was observed that halide ions such as I- can induce significant nanostructuring of the oxidized Cu surface, even at open circuit potential, including the formation of Cu crystals with well-defined shapes. Furthermore, the presence of Cl-, Br-, and I- was found to lower the overpotential and to increase the CO2 electroreduction rate on plasma-activated preoxidized Cu catalyst in the order Cl- < Br- < I-, without sacrificing their intrinsically high C2-C3 product selectivity (∼65% total Faradaic efficiency at -1.0 V vs RHE). This enhancement in catalytic performance is mainly attributed to the specific adsorption of halides with a higher coverage on our oxidized Cu surface during the reaction, which have been previously reported to facilitate the formation and stabilization of the carboxyl (∗COOH) intermediate by partial charge donation from the halide ions to CO2. (Graph Presented). © 2017 American Chemical Society.

In situ Raman and in situ EPR spectroscopy in combination with electrochemistry have been used to investigate the behavior of mixed cobalt nickel and cobalt copper oxides in the oxygen evolution reaction (OER). All experiments were carried out in homemade electrochemical cells using 0.1 M KOH as the electrolyte. The OER activities vary depending on the annealing conditions of the catalyst precursors, also reflected by different behaviours during the in situ spectroscopic experiments. The different activity of the Co/Ni oxides is most likely related to the formation of either γ- or β-NiO(OH), characterized by distinct features in the Raman spectra. Thus, a higher percentage of β-NiO(OH) is present in the more active catalyst. A different behaviour of Co/Cu catalysts has been shown by in situ Raman spectroscopy too, but the active phase could not be identified because of missing spectral features. However, in situ EPR spectroscopy revealed the partial dissolution of Cu(II), suggesting the formation of a Co-enriched oxide/hydroxide surface. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Highly active electrocatalysts for the oxygen evolution (OER) reaction are in most cases powder nanomaterials, which undergo substantial changes upon applying the high potentials required for high-current-density oxygen evolution. Owing to the vigorous gas evolution, the durability under OER conditions is disappointingly low for most powder electrocatalysts as there are no strategies to securely fix powder catalysts onto electrode surfaces. Thus reliable studies of catalysts during or after the OER are often impaired. Herein, we propose the use of composites made from precursors of polybenzoxazines and organophilically modified NiFe layered double hydroxides (LDHs) to form a stable and highly conducting catalyst layer, which allows the study of the catalyst before and after electrocatalysis. Characterization of the material by XRD, SEM, and TEM before and after 100 h electrolysis in 5 m KOH at 60 °C and a current density of 200 mA cm−2 revealed previously not observed structural changes. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Understanding the deactivation of transition-metal carbide catalysts during hydrodeoxygenation (HDO) reactions is of great importance for improving the production of the second generation fuels from biomass. Based on a combined experimental and theoretical study, we present a mechanistic model for the deactivation of molybdenum carbide catalysts during phenol HDO in the presence of water. At increased water pressure, water molecules preferentially bind to the surface, and active sites are no longer accessible for phenol. In line with first principle calculations, experiments reveal that this process is fully reversible because the reduction of the water partial pressure results in a threefold increase in conversion. The direct deoxygenation of phenol was calculated to be the most favorable pathway, which is governed by the structure of the phenol adsorption complex on the surface at high hydrogen coverage. This is consistent with the experimentally observed high benzene selectivity (85 %) for phenol HDO over MoCx/HCS (hollow carbon spheres) catalyst. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Glycerol is a major by-product of the biodiesel production and is therefore produced in high quantities. While currently there are limited possible applications for this highly functionalized molecule, glycerol can be a cheap and abundant feedstock for value-added products that are accessible by selective oxidation. Usually, the selective oxidation of glycerol utilizes expensive noble metal catalysts, such as Au, Pt, and Pd. Here we report the selective oxidation of glycerol in basic media, using ordered mesoporous Cu-Al2O3 catalysts with various Cu loadings prepared by a facile soft-templating method. The materials were characterized in detail by nitrogen physisorption, vis-NIR spectroscopy, EDX, low- and wide-angle XRD, XPS, and TEM. Subsequently the reaction conditions for glycerol oxidation were optimized. The catalytic oxidation of glycerol yields C3 products, such as glyceric acid and tartronic acid, and also C2 and C1 products, such as glycolic acid, oxalic acid, and formic acid. Moreover, the role of the solvent on the catalytic reaction was investigated, and the addition of various co-solvents to the aqueous reaction mixture was found to increase the initial reaction rate up to a factor of three. The trends of the initial reaction rates correlate well with the polarity of the water/co-solvent mixtures. The prepared Cu-Al2O3 catalysts are a more cost-efficient and environmentally viable alternative to the reported noble metal catalysts. © 2017 The Royal Society of Chemistry.

Tandem catalysis is an attractive strategy to intensify chemical technologies. However, simultaneous control over the individual and concerted catalyst performances poses a challenge. We demonstrate that enhanced pore transport within a Co/Al2O3 Fischer–Tropsch (FT) catalyst with hierarchical porosity enables its tandem integration with a Pt/ZSM-5 zeolitic hydrotreating catalyst in a spatially distant fashion that allows for catalyst-specific temperature adjustment. Nevertheless, this system resembles the case of close active-site proximity by mitigating secondary reactions of primary FT α-olefin products. This approach enables the combination of in situ dewaxing with a minimum production of gaseous hydrocarbons (18 wt %) and an up to twofold higher (50 wt %) selectivity to middle distillates compared to tandem pairs based on benchmark mesoporous FT catalysts. An overall 80 % selectivity to liquid hydrocarbons from syngas is attained in one step, attesting to the potential of this strategy for increasing the carbon efficiency in intensified gas-to-liquid technologies. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

LaNiO3 perovskite is an interesting precursor for Ni/La2O3 catalysts for the dry reforming of methane at high temperatures. Precursors have been synthesized by co-precipitation without, with 2.5 at%, and with 5 at% Ru doping. The presence of Ru leads to a stabilization of the perovskite structure and hinders the decomposition into NiO and Ruddlesden-Popper mixed oxides Lan+1NinO3n+1, which was observed for the Ru-free sample upon calcination at 1000 °C (n = 3). Upon reduction in hydrogen, a mechanism involving at least two steps was observed and the first major step was identified as the partial reduction of the precursor leading to a LaNiO2.5-like intermediate. The second major step is the reduction to Ni metal supported on La2O3 independent of the Ru content of the catalyst. In the presence of Ru, indications for Ni-Ru alloy formation and for a higher dispersion of the metallic phase were found. The catalytic activity in DRM of the catalyst containing 2.5% Ru was superior to the catalysts with more or without Ru. Furthermore, the propensity of coke formation was reduced by the presence of Ru. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

We have developed a low-temperature atomic layer deposition (ALD) process for depositing crystalline and phase pure spinel cobalt oxide (Co3O4) films at 120 °C using [Co(tBu2DAD)2] and ozone as coreagent. X-ray diffraction, UV-vis spectroscopy, atomic force microscopy, field emission scanning electron microscopy, X-ray photoelectron spectroscopy, and time-of-flight elastic recoil detection analysis were performed to characterize the structure and properties of the films. The as-deposited Co3O4 films are crystalline with a low amount of impurities (<2% C and <5% H) despite low deposition temperatures. Deposition of Co3O4 onto thin TiO2 photoanodes (100 nm) for water oxidation resulted in 30% improvement of photocurrent (after 10 ALD cycles yielding small Co3O4 particles) as compared to pristine TiO2 films), and exhibited no detrimental effects on photocurrent response up to 300 deposition cycles (approximately 35 nm thick films), demonstrating the applicability of the developed ALD process for deposition of effective catalyst particles and layers in photoelectrochemical water-splitting devices. © 2017 American Chemical Society.

Employing an oxidative photodeposition of CrOx the well-known Rh/CrOx co-catalyst system was prepared on different semiconductors. These photocatalysts showed up to 25% higher overall water splitting activities compared with conventionally prepared materials. The enhancement is attributed to a favorable selective deposition of CrOx caused by charge-directed deposition. © 2017 The Royal Society of Chemistry.

Developing high-performance non-precious metal catalysts (NPMCs) for the oxygen-reduction reaction (ORR) is of critical importance for sustainable energy conversion. We report a novel NPMC consisting of iron carbide (Fe3C) nanoparticles encapsulated in N-doped bamboo-like carbon nanotubes (b-NCNTs), synthesized by a new metal-organic framework (MOF)-templated assembly approach. The electrocatalyst exhibits excellent ORR activity in 0.1m KOH (0.89V at -1mAcm-2) and in 0.5m H2SO4 (0.73V at -1mAcm-2) with a hydrogen peroxide yield of below 1% in both electrolytes. Due to encapsulation of the Fe3C nanoparticles inside porous b-NCNTs, the reported NPMC retains its high ORR activity after around 70hours in both alkaline and acidic media. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

By a combination of FT-NIR Raman spectroscopy, infrared spectroscopy of CO adsorption under ultrahigh vacuum conditions (UHV-IR) and Raman spectroscopy in the line scanning mode the formation of a reduced titania phase in a commercial Au/TiO2 catalyst and in freshly prepared Au/anatase catalysts was detected. The reduced phase, formed at the Au-TiO2 interface, can serve as nucleation point for the formation of stoichiometric rutile. TinO2n−1 Magnéli phases, structurally resembling the rutile phase, might be involved in this process. The formation of the reduced phase and the rutilization process is clearly linked to the presence of gold nanoparticles and it does not proceed under similar conditions with the pure titania sample. Phase transformations might be both thermally or light induced, however, the colloidal deposition synthesis of the Au/TiO2 catalysts is clearly ruled out as cause for the formation of the reduced phase. © 2017, The Author(s).

Co-based layered double hydroxide (LDH) catalysts with Fe and Al contents in the range of 15 to 45 at % were synthesized by an efficient coprecipitation method. In these catalysts, Fe3+ or Al3+ ions play an essential role as trivalent species to stabilize the LDH structure. The obtained catalysts were characterized by a comprehensive combination of surface- and bulk-sensitive techniques and were evaluated for the oxygen evolution reaction (OER) on rotating disk electrodes. The OER activity decreased upon increasing the Al content for the Co- and Al-based LDH catalysts, whereas a synergistic effect in Co- and Fe-based LDHs was observed, which resulted in an optimal Fe content of 35 at %. This catalyst was spray-coated on Ni foam electrodes and showed very good stability in a flow-through cell with a potential of approximately 1.53 V at 10 mA cm−2 in 1 m KOH for at least 48 h. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Prompted by the impact of Ni-based support materials on the intrinsic activity of electrocatalysts, we investigated the influence of partial Co substitution by Ni during the reductive thermal synthesis of cobalt-cobalt phosphide nanoparticles from triphenylphosphine complexes. The obtained catalysts were characterised by X-ray diffraction and electrochemistry. Increasing the amount of Ni in the precursor complexes leads to materials with lower overpotential for the OER at low current densities, and lower Tafel slopes. Co nanoparticles, which are only formed in materials with low Ni content, increase the intrinsic material conductivity and reduce the OER overpotential at high current densities. © 2017

Nitrogen-doped carbon nanotubes (NCNTs) were used as a support for iron (Fe) nanoparticles applied in carbon dioxide (CO2) hydrogenation at 633 K and 25 bar (1 bar = 105 Pa). The Fe/NCNT catalyst promoted with both potassium (K) and manganese (Mn) showed high performance in CO2 hydrogenation, reaching 34.9% conversion with a gas hourly space velocity (GHSV) of 3.1 L·(g·h)−1. Product selectivities were high for olefin products and low for short-chain alkanes for the K-promoted catalysts. When Fe/NCNT catalyst was promoted with both K and Mn, the catalytic activity was stable for 60 h of reaction time. The structural effect of the Mn promoter was demonstrated by X-ray diffraction (XRD), temperature-programmed reduction (TPR) with molecular hydrogen (H2), and in situ X-ray absorption near-edge structure (XANES) analysis. The Mn promoter stabilized wüstite (FeO) as an intermediate and lowered the TPR onset temperature. Catalytic ammonia (NH3) decomposition was used as an additional probe reaction for characterizing the promoter effects. The Fe/NCNT catalyst promoted with both K and Mn had the highest catalytic activity, and the Mn-promoted Fe/NCNT catalysts had the highest thermal stability under reducing conditions. © 2017 THE AUTHORS

The overriding obstacle to mass production of hydrogen from water as the premium fuel for powering our planet is the frustratingly slow kinetics of the oxygen evolution reaction (OER). Additionally, inadequate understanding of the key barriers of the OER is a hindrance to insightful design of advanced OER catalysts. This study presents ultrathin amorphous high-surface area nickel boride (NixB) nanosheets as a low-cost, very efficient and stable catalyst for the OER for electrochemical water splitting. The catalyst affords 10 mA cm-2 at 0.38 V overpotential during OER in 1.0 m KOH, reducing to only 0.28 V at 20 mA cm-2 when supported on nickel foam, which ranks it among the best reported nonprecious catalysts for oxygen evolution. Operando X-ray absorption fine-structure spectroscopy measurements reveal prevalence of NiOOH, as well as Ni-B under OER conditions, owing to a Ni-B core at nickel oxyhydroxide shell (Ni-B at NiOxH) structure, and increase in disorder of the NiOxH layer, thus revealing important insight into the transient states of the catalyst during oxygen evolution. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The performance of polymer electrolyte fuel cells is strongly correlated to the electrocatalytic activity and stability. In particular, the latter is the result of an interplay between different degradation mechanisms. The essential high stability, demanded for real applications, requires the synthesis of advanced electrocatalysts that withstand the harsh operation conditions. In the first part of this study, the synthesis of oxygen reduction electrocatalysts consisting of Pt-Co (i.e., Pt5Co, Pt3Co, and PtCo) alloyed nanoparticles encapsulated in the mesoporous shell of hollow graphitic spheres (HGS) is reported. The mass activities of the activated catalysts depend on the initial alloy composition and an activity increase on the order of two to threefold, compared to pure Pt@HGS, is achieved. The key point of the second part is the investigation of the degradation of PtCo@HGS (showing the highest activity). Thanks to pore confinement, the impact of dissolution/dealloying and carbon corrosion can be studied without the interplay of other degradation mechanisms that would induce a substantial change in the particle size distribution. Therefore, impact of the upper potential limit and the scan rates on the dealloying and electrochemical surface area evolution can be examined in detail. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

By doping the TiO2 support with nitrogen, strong metal-support interactions (SMSI) in Pd/TiO2 catalysts can be tailored to obtain high-performance supported Pd nanoparticles (NPs) in nitrobenzene (NB) hydrogenation catalysis. According to the comparative studies by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), and diffuse reflectance CO FTIR (CO-DRIFTS), N-doping induced a structural promoting effect, which is beneficial for the dispersion of Pd species on TiO2. High-angle annular dark-field scanning transmission electron microscopy study of Pd on N-doped TiO2 confirmed a predominant presence of sub-2 nm Pd NPs, which are stable under the applied hydrogenation conditions. XPS and CO-DRIFTS revealed the formation of strongly coupled Pd-N species in Pd/TiO2 with N-doped TiO2 as support. Density functional theory (DFT) calculations over model systems with Pdn (n = 1, 5, or 10) clusters deposited on TiO2(101) surface were performed to verify and supplement the experimental observations. In hydrogenation catalysis using NB as a model molecule, Pd NPs on N-doped TiO2 outperformed those on N-free TiO2 in terms of both catalytic activity and stability, which can be attributed to the presence of highly dispersed Pd NPs providing more active sites, and to the formation of Pd-N species favoring the dissociative adsorption of the reactant NB and the easier desorption of the product aniline. (Figure Presented). © 2016 American Chemical Society.

Engineering stable electrodes using highly active catalyst nanopowders for electrochemical water splitting remains a challenge. We report an innovative and general approach for attaining highly stable catalyst films with self-healing capability based on the in situ self-assembly of catalyst particles during electrolysis. The catalyst particles are added to the electrolyte forming a suspension that is pumped through the electrolyzer. Particles with negatively charged surfaces stick onto the anode, while particles with positively charged surfaces stick to the cathode. The self-assembled catalyst films have self-healing properties as long as sufficient catalyst particles are present in the electrolyte. The proof-of-concept was demonstrated in a non-zero gap alkaline electrolyzer using NiFe-LDH and NixB catalyst nanopowders for anode and cathode, respectively. Steady cell voltages were maintained for at least three weeks during continuous electrolysis at 50–100 mA cm−2. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

In this work we present a detailed preparation method for mesoporous hollow graphitic spheres (HGS) that has been developed in our laboratory over recent years. The aim of this description is to enable the reader to reproduce the procedure by highlighting important steps, conditions, and challenges during the synthesis. HGS have initially been developed as a carbon support to enhance the stability of metal catalysts in the oxygen reduction reaction (ORR) of PEM fuel cells via pore confinement. The HGS are synthesized in a multistep procedure employing a core-shell silica template, DVB as carbon source, and iron as graphitization catalyst. The silica template is removed by leaching with hydrofluoric acid yielding the mesoporous carbon support, where metal catalysts can be introduced via incipient wetness method followed by a reduction in hydrogen. The whole procedure allows high control over product parameters such as core or shell diameter and graphitization degree. Thus, it can be adapted and tuned to match the desired properties of high performance materials for various potential applications. © 2017 American Chemical Society.

Metal oxides and carbon-based materials are the most promising electrode materials for a wide range of low-cost and highly efficient energy storage and conversion devices. Creating unique nanostructures of metal oxides and carbon materials is imperative to the development of a new generation of electrodes with high energy and power density. Here we report our findings in the development of a novel graphene aerogel assisted method for preparation of metal oxide nanoparticles (NPs) derived from bulk MOFs (Co-based MOF, Co(mIM)2 (mIM = 2-methylimidazole). The presence of cobalt oxide (CoOx) hollow NPs with a uniform size of 35 nm monodispersed in N-doped graphene aerogels (NG-A) was confirmed by microscopic analyses. The evolved structure (denoted as CoOx/NG-A) served as a robust Pt-free electrocatalyst with excellent activity for the oxygen reduction reaction (ORR) in an alkaline electrolyte solution. In addition, when Co was removed, the resulting nitrogen-rich porous carbon-graphene composite electrode (denoted as C/NG-A) displayed exceptional capacitance and rate capability in a supercapacitor. Further, this method is readily applicable to creation of functional metal oxide hollow nanoparticles on the surface of other carbon materials such as graphene and carbon nanotubes, providing a good opportunity to tune their physical or chemical activities. © 2017 American Chemical Society.

A series of ZnO/Cr2O3 catalysts with different Zn:Cr ratios was prepared by coprecipitation at a constant pH of 7 and applied in methanol synthesis at 260-300 °C and 60 bar. The X-ray diffraction (XRD) results showed that the calcined catalysts with ratios from 65:35 to 55:45 consist of ZnCr2O4 spinel with a low degree of crystallinity. For catalysts with Zn:Cr ratios smaller than 1, the formation of chromates was observed in agreement with temperature-programmed reduction results. Raman and XRD results did not provide evidence for the presence of segregated ZnO, indicating the existence of Zn-rich nonstoichiometric Zn-Cr spinel in the calcined catalyst. The catalyst with Zn:Cr = 65:35 exhibits the best performance in methanol synthesis. The Zn:Cr ratio of this catalyst corresponds to that of the Zn4Cr2(OH)12CO3 precursor with hydrotalcite-like structure obtained by coprecipitation, which is converted during calcination into a nonstoichiometric Zn-Cr spinel with an optimum amount of oxygen vacancies resulting in high activity in methanol synthesis. Density functional theory calculations are used to examine the formation of oxygen vacancies and to measure the reducibility of the methanol synthesis catalysts. Doping Cr into bulk and the (10-10) surface of ZnO does not enhance the reducibility of ZnO, confirming that Cr:ZnO cannot be the active phase. The (100) surface of the ZnCr2O4 spinel has a favorable oxygen vacancy formation energy of 1.58 eV. Doping this surface with excess Zn charge-balanced by oxygen vacancies to give a 60% Zn content yields a catalyst composed of an amorphous ZnO layer supported on the spinel with high reducibility, confirming this as the active phase for the methanol synthesis catalyst. © 2017 American Chemical Society.

The development of reversible oxygen electrodes, able to drive both the oxygen evolution reaction (OER) and the oxygen reduction reaction (ORR), is still a great challenge. We describe a very efficient and stable bifunctional electrocatalytic system for reversible oxygen electrodes obtained by direct CVD growth of nitrogen-doped carbon nanotubes (NCNTs) on the surface of cobalt boride (CoB) nanoparticles. A detailed investigation of the crystalline structure and elemental distribution of CoB before and after NCNT growth reveals that the NCNTs grow on small CoB nanoparticles formed in the CVD process. The resultant CoB/NCNT system exhibited outstanding activity in catalyzing both the OER and the ORR in 0.1 M KOH with an overvoltage difference of only 0.73 V between the ORR at -1 mA cm-2 and the OER at +10 mA cm-2. The proposed CoB/NCNT catalyst showed stable performance during 50 h of OER stability assessment in 0.1 M KOH. Moreover, CoB/NCNT spray-coated on a gas diffusion layer as an air-breathing electrode proved its high durability during 170 galvanostatic charge-discharge (OER/ORR) test cycles (around 30 h) at ±10 mA cm-2 in 6 M KOH, making it an excellent bifunctional catalyst for potential Zn-air battery application. © 2017 The Royal Society of Chemistry.

Mechanochemical activation of solids can lead to a strong increase in their activity as catalysts in heterogeneously catalyzed reactions. In the following, we report on the effects of solid catalyst activation during ball milling that lead to oscillatory behavior in CO and CO2 formation during propene oxidation. The oscillations arise under in situ ball milling conditions over chromium(III) oxide (Cr2O3) and cerium(IV) oxide (CeO2), respectively. The experiments were conducted under continuous gas flow at ambient pressure and temperature, using both a modified steel and a tungsten carbide milling vessel. Abrasion of particles from the steel milling vessel could be eliminated as the sole cause for the oscillations through substitution by a tungsten carbide milling vessel. The intensity and frequency of oscillations are shown to be dependent on the propene-to-oxygen ratio, the milling frequency, milling ball size and metal oxide used. Overall, Cr2O3 shows higher activity for oscillatory propene combustion under in situ mechanical activation than CeO2. © 2017, The Author(s).

Monocrystalline, yet porous mosaic platelets of cobalt ferrite, CoFe2O4, can be synthesized from a layered double hydroxide (LDH) precursor by thermal decomposition. Using an equimolar mixture of Fe2+, Co2+, and Fe3+ during co-precipitation, a mixture of LDH, (FeIICoII)2/3FeIII 1/3(OH)2(CO3)1/6mH2O, and the target spinel CoFe2O4 can be obtained in the precursor. During calcination, the remaining FeII fraction of the LDH is oxidized to FeIII leading to an overall Co2+:Fe3+ ratio of 1:2 as required for spinel crystallization. This pre-adjustment of the spinel composition in the LDH precursor suggests a topotactic crystallization of cobalt ferrite and yields phase pure spinel in unusual anisotropic platelet morphology. The preferred topotactic relationship in most particles is [111]Spinel∥[001]LDH. Due to the anion decomposition, holes are formed throughout the quasi monocrystalline platelets. This synthesis approach can be used for different ferrites and the unique microstructure leads to unusual chemical properties as shown by the application of the ex-LDH cobalt ferrite as catalyst in the selective oxidation of 2-propanol. Compared to commercial cobalt ferrite, which mainly catalyzes the oxidative dehydrogenation to acetone, the main reaction over the novel ex-LDH cobalt is dehydration to propene. Moreover, the oxygen evolution reaction (OER) activity of the ex-LDH catalyst was markedly higher compared to the commercial material. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

There has been growing interest in the synthesis of efficient reversible oxygen electrodes for both the oxygen reduction reaction (ORR) and the oxygen evolution reactions (OER), for their potential use in a variety of renewable energy technologies, such as regenerative fuel cells and metal-air batteries. Here, a bi-functional electrocatalyst, derived from a novel dicyanamide based nitrogen rich MOF {[Co(bpe)2(N(CN)2)]⋅(N(CN)2)⋅(5 H2O)}n [Co-MOF-1, bpe=1,2-bis(4-pyridyl)ethane, N(CN)2 −=dicyanamide] under different pyrolysis conditions is reported. Pyrolysis of the Co-MOF-1 under Ar atmosphere (at 800 °C) yielded a Co nanoparticle-embedded N-doped carbon nanotube matrix (Co/NCNT-Ar) while pyrolysis under a reductive H2/Ar atmosphere (at 800 °C) and further mild calcination yielded Co3O4@Co core–shell nanoparticle-encapsulated N-doped carbon nanotubes (Co3O4@Co/NCNT). Both catalysts show bi-functional activity towards ORR and OER, however, the core–shell Co3O4@Co/NCNT nanostructure exhibited superior electrocatalytic activity for both the ORR with a potential of 0.88 V at a current density of −1 mA cm−2 and the OER with a potential of 1.61 V at 10 mA cm−2, which is competitive with the most active bi-functional catalysts reported previously. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

In nature, [FeFe]-hydrogenases catalyze the uptake and release of molecular hydrogen (H2) at a unique iron-sulfur cofactor. The absence of an electrochemical overpotential in the H2 release reaction makes [FeFe]-hydrogenases a prime example of efficient biocatalysis. However, the molecular details of hydrogen turnover are not yet fully understood. Herein, we characterize the initial one-electron reduction of [FeFe]-hydrogenases by infrared spectroscopy and electrochemistry and present evidence for proton-coupled electron transport during the formation of the reduced state Hred′. Charge compensation stabilizes the excess electron at the [4Fe-4S] cluster and maintains a conservative configuration of the diiron site. The role of Hred′ in hydrogen turnover and possible implications on the catalytic mechanism are discussed. We propose that regulation of the electronic properties in the periphery of metal cofactors is key to orchestrating multielectron processes. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

In addition to catalytic activity, intrinsic stability, tight immobilization on a suitable electrode surface, and sufficient electronic conductivity are fundamental prerequisites for the long-term operation of particle- and especially powder-based electrocatalysts. We present a novel approach to concurrently address these challenges by using the unique properties of polybenzoxazine (pBO) polymers, namely near-zero shrinkage and high residual-char yield even after pyrolysis at high temperatures. Pyrolysis of a nanocubic prussian blue analogue precursor (KmMnx[Co(CN)6]y⋅n H2O) embedded in a bisphenol A and aniline-based pBO led to the formation of a N-doped carbon matrix modified with MnxCoyOz nanocubes. The obtained electrocatalyst exhibits high efficiency toward the oxygen evolution reaction (OER) and more importantly a stable performance for at least 65 h. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Engineering of controlled hybrid nanocomposites creates one of the most exciting applications in the fields of energy materials and environmental science. The rational design and in situ synthesis of hierarchical porous nanocomposite sheets of nitrogen-doped graphene oxide (NGO) and nickel sulfide (Ni7S6) derived from a hybrid of a well-known nickel-based metal-organic framework (NiMOF-74) using thiourea as a sulfur source are reported here. The nanoporous NGO/MOF composite is prepared through a solvothermal process in which Ni(II) metal centers of the MOF structure are chelated with nitrogen and oxygen functional groups of NGO. NGO/Ni7S6 exhibits bifunctional activity, capable of catalyzing both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) with excellent stability in alkaline electrolytes, due to its high surface area, high pore volume, and tailored reaction interface enabling the availability of active nickel sites, mass transport, and gas release. Depending on the nitrogen doping level, the properties of graphene oxide can be tuned toward, e.g., enhanced stability of the composite compared to commonly used RuO2 under OER conditions. Hence, this work opens the door for the development of effective OER/HER electrocatalysts based on hierarchical porous graphene oxide composites with metal chalcogenides, which may replace expensive commercial catalysts such as RuO2 and IrO2. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chemical vapor synthesis (CVS) is a unique method to prepare well-defined photocatalyst materials with both large specific surface area and a high degree of crystallinity. The obtained β-Ga2O3 nanoparticles were optimized for photocatalysis by reductive photodeposition of the Rh/CrOx co-catalyst system. The influence of the degree of crystallinity and the specific surface area on photocatalytic aqueous methanol reforming and overall water splitting (OWS) was investigated by synthesizing β-Ga2O3 samples in the temperature range from 1000 °C to 1500 °C. With increasing temperature, the specific surface area and the microstrain were found to decrease, whereas the degree of crystallinity and the crystallite size increased. Whereas the photocatalyst with the highest specific surface area showed the highest aqueous methanol reforming activity, the highest OWS activity was that for the sample with an optimum ratio between high degree of crystallinity and specific surface area. Thus, it was possible to show that the facile aqueous methanol reforming and the demanding OWS have different requirements for high photocatalytic activity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

As part of an ongoing effort to understand the deactivation and improve the stability of metal oxide-supported Au catalysts in the low-temperature CO oxidation reaction while maintaining their high activity, we have investigated the influence of a mesoporous silica SBA-15 substrate on the activity and stability of Au/TiO2 catalysts, which consist of a SBA-15 support surface modified by a monolayer of TiOx with Au nanoparticles on top. The extent of the TiOx surface modification was systematically increased, while the Au loading and the Au particle sizes were largely kept constant. Employing kinetic measurements at three different temperatures (30 °C, 80 °C, 180 °C) and a number of ex situ methods as well as in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) for catalyst characterization, we found that the activity of these catalysts increases significantly with the Ti concentration and with reaction temperature. The tendency for deactivation remains essentially unchanged. Detailed in situ DRIFTS measurements reveal that the Au nanoparticles are largely formed on the TiOx surface-modified areas of the SBA-15 support and that the tendency for surface carbonate formation is very low. The observed deactivation may at least partly be related to the accumulation of molecularly adsorbed H2O species, in particular at low temperatures (30 °C). These are likely to be formed from surface hydroxyl groups, they may affect the reaction either by blocking of active sites or by blocking the adsorption of reactants on the substrate. Other effects, such as reaction induced changes in the titania layer, must however, play a role as well, both at 80 °C and in particular at 180 °C, where accumulation of adsorbed species is negligible. The mechanistic ideas are supported by reactivation tests subsequent to calcination at 400 °C, which were found to fully restore the initial activity. © 2017 Elsevier Inc.

The growth of metal–organic framework (ZIF-67) nanocrystals on nickel foam (NF), followed by carbonization in diluted H2, leads to a nitrogen-doped carbon-nanotube-grafted cobalt/carbon polyhedra film on NF. The obtained material serves as a highly active binder-free electrocatalyst for both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER), enabling high-performance alkaline (0.1 m KOH) water electrolysis with potentials of 1.62 and 0.24 V, respectively, at OER and HER current densities of 10 mA cm−2. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

The development of a versatile microbiosensor for hydrogen detection is reported. Carbon-based microelectrodes were modified with a [NiFe]-hydrogenase embedded in a viologen-modified redox hydrogel for the fabrication of a sensitive hydrogen biosensor By integrating the microbiosensor in a scanning photoelectrochemical microscope, it was capable of serving simultaneously as local light source to initiate photo(bio)electrochemical reactions while acting as sensitive biosensor for the detection of hydrogen. A hydrogen evolution biocatalyst based on photosystem 1-platinum nanoparticle biocomplexes embedded into a specifically designed redox polymer was used as a model for proving the capability of the developed hydrogen biosensor for the detection of hydrogen upon localized illumination. The versatility and sensitivity of the proposed microbiosensor as probe tip allows simplification of the set-up used for the evaluation of complex electrochemical processes and the rapid investigation of local photoelectrocatalytic activity of biocatalysts towards light-induced hydrogen evolution. © 2017 Elsevier B.V.

Here we report on an entirely new kind of bioelectronic device – a solar biosupercapacitor, which is built from a dual-feature photobioanode combined with a double-function enzymatic cathode. The self-charging biodevice, based on transparent nanostructured indium tin oxide electrodes modified with biological catalysts, i.e. thylakoid membranes and bilirubin oxidase, is able to capacitively store electricity produced by direct conversion of radiant energy into electric energy. When self-charged during 10 min, using ambient light only, the biosupercapacitor provided a maximum of 6 mW m− 2 at 0.20 V. © 2016 Elsevier B.V.

Nanoporous (np) gold is a promising catalyst material for selective oxidation reactions. Especially the addition of oxide deposits like ceria (CeO2) promises enhanced morphological stability for high temperature applications. Describing such temperature induced morphological changes in porous materials is challenging. Here, X-ray nanoanalysis is particularly promising due to the high penetration depth that allows studying of the bulk properties with high spatial sensitivity. We applied soft X-ray small angle scattering (SAXS) to determine temperature induced structural changes in nanoporous gold catalysts. The results show that CeO2 deposits enhance the temperature stability of the nanoporous gold catalyst. Moreover, we demonstrate the ability of soft X-rays to selectively provide structural information on the stabilizing cerium oxide deposits via resonant, anomalous SAXS (ASAXS) measurements at the cerium M-edge, revealing no growth of the ceria particles. © 2017 The Royal Society of Chemistry.

In situ ball milling of solid catalysts is a promising yet almost unexplored concept for boosting catalytic performance. The continuous preferential oxidation of CO (CO-PROX) under in situ ball milling of Cu-based catalysts such as Cu/Cr2O3 is presented. At temperatures as low as −40 °C, considerable activity and more than 95 % selectivity were achieved. A negative apparent activation energy was observed, which is attributed to the mechanically induced generation and subsequent thermal healing of short-lived surface defects. In situ ball milling at sub-zero temperatures resulted in an increase of the CO oxidation rate by roughly 4 orders of magnitude. This drastic and highly selective enhancement of CO oxidation showcases the potential of in situ ball milling in heterogeneous catalysis. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

We report metallic NiPS3@NiOOH core shell heterostructures as an efficient and durable electrocatalyst for the oxygen evolution reaction, exhibiting a low onset potential of 1.48 V (vs RHE) and stable performance for over 160 h. The atomically thin NiPS3 nanosheets are obtained by exfoliation of bulk NiPS3 in the presence of an ionic surfactant. The OER mechanism was studied by a combination of SECM, in situ Raman spectroscopy, SEM, and XPS measurements, which enabled direct observation of the formation of a NiPS3@NiOOH core shell heterostructure at the electrode interface. Hence, the active form of the catalyst is represented as NiPS3@NiOOH core shell structure. Moreover, DFT calculations indicate an intrinsic metallic character of the NiPS3 nanosheets with densities of states (DOS) similar to the bulk material. The high OER activity of the NiPS3 nanosheets is attributed to a high density of accessible active metallic-edge and defect sites due to structural disorder, a unique NiPS3@NiOOH core shell heterostructure, where the presence of P and S modulates the rface electronic structure of Ni in NiPS3, thus providing excellent conductive pathway for efficient electron-transport to the NiOOH shell. These findings suggest that good size control during liquid exfoliation may be advantageously used for the formation of electrically conductive NiPS3@ NiOOH core shell electrode materials for the electrochemical water oxidation.

Bifunctional oxygen electrocatalysts were fabricated following a three-step synthesis method, which consisted of i) liquid-phase exfoliation of graphite in the presence of nitrogen-containing manganese macrocyclic complexes, using DMF as the dispersion medium under formation of few-layer graphene sheets. Subsequently, ii) solvent removal by vacuum filtration and drying, and iii) pyrolysis of the resulting composites under an inert gas atmosphere with subsequent mild calcination yielded manganese oxides embedded within a graphitic carbon matrix (MnOX/G). We further demonstrate that traces of Fe impurities in the used graphite result in enhanced electrocatalytic activity of the MnOX/G towards both the oxygen reduction and the oxygen evolution reactions, owing to synergistic interaction of the iron impurities with the species formed upon thermal decomposition of Mn macrocyclic complexes. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The performance of proton-exchange membrane fuel cells (PEMFCs) is defined by the equally important parameters of the intrinsic activity and stability of the electrocatalysts. This work focuses on the stability of carbon supported high surface area oxygen reduction reaction catalysts at potentials and temperatures similar to the operating conditions of PEMFCs. The catalysts used for this investigation consist of Pt nanoparticles of the same particle size supported on two types of carbon support having different textural properties, i.e., Vulcan and Hollow Graphitic Spheres (HGS). A broad toolbox of characterization techniques is utilized at 60 °C in order to resolve the contribution of the different degradation mechanisms, namely nanoparticle coalescence, metal dissolution and the corrosion of carbon support, to the total active surface area loss. The results obtained by investigating the impact of temperature, potential treatment and catalyst layer morphology on the aging behavior lead to a deeper understanding of the aging mechanisms and their interrelation at application-relevant conditions. Moreover, the previously reported improved performance of the Pt/HGS catalyst is confirmed also under higher temperatures. The experimental approach introduced in this work, highlights new challenges for high-temperature degradation investigations with supported PEMFC catalyst. © 2016 Elsevier Ltd

ITQ-8 is a new hydrous layer silicate (HLS) with a chemical composition of [C4H8(C7H13N)2]8 [Si64O128(OH)16]·48H2O per unit cell. The synthesis of ITQ-8 was first described in 2002 by Díaz-Cabañas et al., the structure of this material, however, remained unsolved at that time. Physico-chemical characterization using solid-state NMR spectroscopy, SEM, TG-DTA, and FTIR spectroscopy confirmed that ITQ-8 is a layer silicate. The XRD powder pattern was indexed in the monoclinic system with lattice parameters of a0 = 35.5168(5) Å, b0 = 13.3989(2) Å, c0 = 16.0351(2) Å, β = 106.74(2)°. The crystal structure was solved by simulated annealing. Rietveld refinement of the structure in space group C2/c converged to residual values of RBragg = 0.023, RF = 0.022 and chi2 = 2.3 confirming the structure model. The structure of ITQ-8 contains silicate layers with a topology that resembles a (11-1) section of the framework of zeolite levyne. So far, this layer topology is unique among layer silicates. The layer can be regarded as made up of 4-, 6-, double-six and 8-rings which are interconnected to form cup-like "half-cages". Unlike other HLSs, which possess impermeable silicate layers, ITQ-8 contains 8-rings pores with a free diameter of 3.5 Å × 3.4 Å and can be regarded as a "small-pore layer silicate". In the crystal structure, the organic cations, 1,4-diquiniclidiniumbutane, used as structure directing agents during synthesis are intercalated between the silicate layers. Clusters (bands) of water molecules which are hydrogen bonded to each other and to the terminal Si-OH/Si-O- groups are located between the organic cations and interconnect the silicate layers. ITQ-8 is a very interesting material as precursor for the synthesis of microporous framework silicates by topotactic condensation or interlayer expansion reactions leading to 3D micro-pore systems which may be useful in applications as e.g. catalysts, catalyst supports and adsorbents of for separation. © The Royal Society of Chemistry 2016.

RuO2 nanoparticles supported on multi-walled carbon nanotubes (CNTs) functionalized with oxygen (OCNTs) and nitrogen (NCNTs) were employed for the oxygen evolution reaction (OER) in 0.1 M KOH. The catalysts were synthesized by metal-organic chemical vapor deposition using ruthenium carbonyl (Ru3(CO)12) as Ru precursor. The obtained RuO2/OCNT and RuO2/NCNT composites were characterized using TEM, H2-TPR, XRD and XPS in order probe structure-activity correlations, particularly, the effect of the different surface functional groups on the electrochemical OER performance. The electrocatalytic activity and stability of the catalysts with mean RuO2 particle sizes of 13-14 nm was evaluated by linear sweep voltammetry, cyclic voltammetry, and chronopotentiometry, showing that the generation of nitrogen-containing functional groups on CNTs was beneficial for both OER activity and stability. In the presence of RuO2, carbon corrosion was found to be significantly less severe. © 2016 Science Press and Dalian Institute of Chemical Physics. All rights reserved.

A series of Co-modified Cu/ZnO/Al2O3 methanol synthesis catalysts with different Na loadings was prepared and applied in higher alcohol synthesis (HAS) at 280 °C, 60 bar and a ratio of H2/CO = 1. The bulk and surface properties of the catalysts were characterized after reduction and after 40 h time on stream (TOS) without exposing the catalysts to air during the transfer and the measurements. Increased presence of metallic Co0 after reduction at 350 °C was confirmed by X-ray photoelectron spectroscopy indicating metallic Cu0 to act as a reduction promoter. Catalysts with low Na loadings (≤0.6 wt%) showed strong initial deactivation presumably due to coking of isolated Co0 surface sites favoring hydrocarbon formation. The selectivity to higher alcohols gradually increased during the first 10 h TOS indicating enhanced Cu-Co surface alloy formation considered as active sites for HAS. In contrast, with high Na loadings (≥0.8 wt%) deactivation did not occur and stable performance with constant CO conversion and product distribution was observed indicating significantly altered structural properties. High Na loadings caused the stabilizing amorphous oxide matrix to collapse resulting in strong sintering of the metallic Cu particles, and an increased carbidization of metallic Co0 forming bulk Co2C was observed by X-ray diffraction. Close contact between metallic Co0 and Co2C, which is known to facilitate molecular CO adsorption, is assumed to generate additional active sites for HAS. © 2016 Elsevier Inc. All rights reserved.

With the help of a technique combining in situ electrical impedance spectroscopy and DRIFT spectroscopy, we observed directly the formation of ammonium ion (NH4 +) intermediates resulting from the interaction of NO and NH3 on Fe-ZSM-5 catalysts for selective catalytic reduction by NH3 (NH3-SCR). The formed NH4 + intermediates, indicating the activation of NO in the presence of adsorbed NH3, were found to be strongly related to the NH3-SCR activity of Fe-ZSM-5 catalysts at low temperatures. These findings, which are not easily achievable by conventional methods, provide new and important perspectives to understand mechanistically the NH3-SCR reaction over Fe-zeolite catalysts. (Graph Presented). © 2016 American Chemical Society.

Hydrogen peroxide (H2O2) is one of the most important reactive oxygen species, and it is involved in a number of cellular processes ranging from signal transduction to immune defence and oxidative stress. It is of great interest to intracellularly quantify H2O2 to improve the understanding of its role in disease processes. In this study, we present an amperometric nanosensor for the quantification of H2O2 at the single-cell level. Deposition of the electrocatalyst Prussian Blue on carbon nanoelectrodes enables selective H2O2 reduction at mild potentials. Owing to their small size and needle-type shape, these nanoelectrodes can penetrate the membrane of single living cells, causing only minimal perturbation. The nanosensors allow for the monitoring of penetration-induced oxidative outbursts as well as the uptake of H2O2 from the extracellular environment in single murine macrophages. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Nanocasting is a general and widely applied method in the generation of porous materials during which a sacrificial solid template is used as a mold on the nanoscale. Ideally, the resulting structure is the inverse of the template. However, replication is not always as direct as anticipated, so the influences of the degree of pore filling and of potential restructuring processes after removal of the template need to be considered. These apparent limitations give rise to opportunities in the synthesis of poly(styrene-co-divinylbenzene) (PSD) polymer networks of widely varying porosities (BET surface area=63–562 m2g−1; Vtot=0.18–1.05 cm3g−1) by applying a single synthesis methodology. In addition, spatially selective sulfonation on the nanoscale seems possible. Together, nanocasting and sulfonation enable rational catalyst design. The highly porous nanocast and predominantly surface-sulfonated PSD networks approach the activity of the corresponding molecular catalyst, para-toluenesulfonic acid, and exceed those of commercial ion-exchange polymers in the depolymerization of macromolecular inulin. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

An iron based catalyst supported on an N-functionalized carbon nanotube (NCNT) was promoted with potassium and manganese as follows: Fe/NCNT, K/Fe/NCNT, Mn/Fe/NCNT, and K/Mn/Fe/NCNT for CO2 hydrogenation. Time-resolved reduction X-ray absorption near edge spectroscopy (XANES) showed mixed phases of Fe, FeO, Fe3O4, and Fe2O3 resulting from K/Fe/NCNT, and of FeO and Fe3O4 resulting from Mn/Fe/NCNT. The product distributions and growth probability of n-alkanes during CO2 hydrogenation indicated that the potassium-promoted iron catalysts performed Fischer-Tropsch (FT) synthesis under steady state at 60 h. 1-Alkenes desorbed from the FT sites with the potassium-promoted catalysts, (K/Fe/NCNT and K/Mn/Fe/NCNT), with low methane formation. Small amounts of 1-alkene, along with high methanation, were produced from the potassium-unpromoted catalysts, (Fe/NCNT and Mn/Fe/NCNT), indicating high local H2:CO ratios on the catalyst surfaces. K/Fe/NCNT and K/Mn/Fe/NCNT catalysts also produced ethanol. Thus, potassium is a key promoter providing active species of the catalysts for alkene and ethanol formation. Reduced surrounding of the NCNT support, potassium as an electronic promoter together with manganese as a structural promoter made the iron-active phase well suitable for CO2 hydrogenation producing mainly alkenes and ethanol. © 2016 Elsevier B.V.

Nanoscopic gold particles have gained very high interest because of their promising catalytic activity for various chemicals reactions. Among these reactions, low-temperature CO oxidation is the most extensively studied one due to its practical relevance in environmental applications and the fundamental problems associated with its very high activity at low temperatures. Gold nanoparticles supported on manganese oxide belong to the most active gold catalysts for CO oxidation. Among a variety of manganese oxides, Mn2O3 is considered to be the most favorable support for gold nanoparticles with respect to catalytic activity. Gold on MnO2 has been shown to be significantly less active than gold on Mn2O3 in previous work. In contrast to these previous studies, in a comprehensive study of gold nanoparticles on different manganese oxides, we developed a gold catalyst on MnO2 nanostructures with extremely high activity. Nanosized gold particles (2-3 nm) were supported on α-MnO2 nanowires and mesoporous β-MnO2 nanowire arrays. The materials were extremely active at very low temperature (-80 °C) and also highly stable at 25 °C (70 h) under normal conditions for CO oxidation. The specific reaction rate of 2.8 molCO·h-1·gAu -1 at a temperature as low as -85 °C is almost 30 times higher than that of the most active Au/Mn2O3 catalyst. © 2016 American Chemical Society.

Evaluation of the long-term stability of electrocatalysts is typically performed using galvanostatic polarization at a predefined current density. A stable or insignificant increase in the applied potential is usually interpreted as high long-term stability of the tested catalyst. However, effects such as (i) electrochemical degradation of a catalyst due to its oxidation, (ii) blocking of the catalyst surface by evolved gas bubbles, and (iii) detachment of the catalyst from the electrode surface may lead to a decrease of the catalyst's active surface area being exposed to the electrolyte. In order to separate these effects and to evaluate the true electrochemical degradation of electrocatalysts, an advanced evaluation protocol based on subsequently performed electrochemical impedance, double layer capacitance, cyclic voltammetry, and galvanostatic polarization measurements was developed and used to evaluate the degradation of IrO2 particles drop-coated on glassy carbon rotating disk electrode using Nafion as a binder. A flow-through electrochemical cell was developed enabling circulation of the electrolyte leading to an efficient removal of evolved oxygen bubbles even at high current densities of up to 250 mA/cm2. The degradation rate of IrO2 was evaluated over 225 test cycles (0.733 ± 0.022 mV/h) with a total duration of galvanostatic polarization measurements of over 55 h. © 2016 American Chemical Society.

Developing electrocatalysts with low cost, high activity, and good durability is urgently demanded for the wide commercialization of fuel cells. By taking advantage of nanostructure engineering, we fabricated PtAg nanotubular aerogels (NTAGs) with high electrocatalytic activity and good durability via a simple galvanic replacement reaction between the in situ spontaneously gelated Ag hydrogel and the Pt precursor. The PtAg NTAGs have hierarchical porous network features with primary networks and pores from the interconnected nanotubes of the aerogel and secondary networks and pores from the interconnected thin nanowires on the nanotube surface, and they show very high porosities and large specific surface areas. Due to the unique structure, the PtAg NTAGs exhibit greatly enhanced electrocatalytic activity toward formic acid oxidation, reaching 19 times higher metal-based mass current density as compared to the commercial Pt black. Furthermore, the PtAg NTAGs show outstanding structural stability and electrochemical durability during the electrocatalysis. Noble metal-based NTAGs are promising candidates for applications in electrocatalysis not only for fuel cells, but also for other energy-related systems. © 2016 American Chemical Society.

Proton transport studies revealed the different influence of Fe and Cu cations on the NH3-zeolite interaction and the NO-zeolite interaction in the presence of adsorbed NH3. At low temperatures, after NH3 saturation, Cu-ZSM-5 is more reactive than Fe-ZSM-5 for NO activation forming highly mobile NH4 + intermediates. © The Royal Society of Chemistry 2016.

Catalysis is at the core of almost every established and emerging chemical process and also plays a central role in the quest for novel technologies for the sustainable production and conversion of energy. Particularly since the early 2000s, a great surge of interest exists in the design and application of micro- and nanometer-sized materials with hollow interiors as solid catalysts. This review provides an updated and critical survey of the ever-expanding material architectures and applications of hollow structures in all branches of catalysis, including bio-, electro-, and photocatalysis. First, the main synthesis strategies toward hollow materials are succinctly summarized, with emphasis on the (regioselective) incorporation of various types of catalytic functionalities within their different subunits. The principles underlying the scientific and technological interest in hollow materials as solid catalysts, or catalyst carriers, are then comprehensively reviewed. Aspects covered include the stabilization of catalysts by encapsulation, the introduction of molecular sieving or stimuli-responsive "auxiliary" functionalities, as well as the single-particle, spatial compartmentalization of various catalytic functions to create multifunctional (bio)catalysts. Examples are also given on the applications which hollow structures find in the emerging fields of electro- and photocatalysis, particularly in the context of the sustainable production of chemical energy carriers. Finally, a critical perspective is provided on the plausible evolution lines for this thriving scientific field, as well as the main practical challenges relevant to the reproducible and scalable synthesis and utilization of hollow micro- and nanostructures as solid catalysts. © 2016 American Chemical Society.

Coal is an earth-abundant energy resource, however, its direct combustion results in serious environmental pollution. Therefore, it becomes important to design value-added products from coal and to maximize its value chain. Herein, brown coal was used to develop non-precious metal catalysts for the oxygen reduction reaction (ORR) in fuel cells as green energy conversion systems. The brown coal was first pretreated with different acids, followed by N-doping at 800 °C in a stream of NH3. A trace amount of Fe was further added to improve the electrocatalytic performance of the prepared catalyst towards ORR. The prepared coal-derived N-doped carbon further modified with 0.5% Fe exhibited onset potential of 0.92 V vs. RHE at a current density of -0.1 mA cm-2 and a predominantly 4-electron transfer pathway of oxygen to water in 0.1 M NaOH, which was evaluated by RDE and RRDE. The prepared electrocatalysts were further characterized by elemental analysis, XRD, Raman and XPS. The results suggest that the coal-derived ORR catalyst have convoluted graphitic and amorphous carbon structures. The N-content increased after acid-pretreatment and subsequent functionalization with nitrogen, while it slightly decreased after Fe incorporation apparently due to coordination of Fe with N. ORR activity enhancement after the incorporation of Fe is expected to mainly arise from a synergetic effect involving the interaction of Fe with N groups distributed in the carbon matrix. © 2016 Elsevier Ltd. All rights reserved.

Copper and iron bimetal modified Al-rich Beta zeolites from template-free synthesis were prepared for selective catalytic reduction (SCR) of NOx with NH3 in exhaust gas streams. Comparing to the Cu-based and Fe-based mono-component Beta catalysts, Cu(3.0)-Fe(1.3)-Beta bi-component catalyst shows better low-temperature activity and wider reaction-temperature window. Over 80% of NO conversion can be achieved at the temperature region of 125–500 °C. Due to the synergistic effect of copper and iron evidenced by XRD, UV–Vis–NIR, EPR and XPS measurements, the dispersion state of active components as well as the ratio of Cu2+/Cu+ and Fe3+/Fe2+ were improved over Cu(3.0)-Fe(1.3)-Beta. Isolated Cu2+ and Fe3+ ions which located at the exchange sites could be the active species at the low-temperature region, while FeOx cluster species may be more important to the high-temperature activity. During the test of sulfur resistance, Fe-containing samples including Cu(3.0)-Fe(1.3)-Beta and Fe(2.7)-Beta-4 present better performance compared to Cu(4.1)-Beta-4. Deactivation of Cu-based catalyst is attributed to the easier deposition of sulfates over the surface according to the results of TGA coupled with TPD experiments. © 2016 Elsevier Inc.

To accelerate the large-scale commercialization of electrochemical energy storage and conversion technologies through water splitting and regeneration in reversible fuel cells, cost-effective, highly efficient, and durable reversible oxygen electrodes are required. We report a comparatively simple approach to modify a group of oxygen-evolving perovskites based on lanthanum cobaltite into effective bifunctional systems through partial atom substitution, which, upon intermixing with nitrogen-doped carbon nanotubes, achieve remarkably low round-trip overvoltage of <850mV in the electrocatalysis of oxygen reduction and oxygen evolution in an alkaline electrolyte, KOH (0.1m). Besides the bifunctional electrocatalytic performance, the composite systems with a low Fe content possessed promising long-term stability. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Two types of Beta zeolites, one from organotemplate-free synthesis with a Si/Al ratio of 9 and the other from a commercial one with a Si/Al ratio of 19, were employed here to dope Fe for NH3-SCR of NOx. Fe-Beta (Si/Al = 9) exhibits much higher activity than Fe-Beta (Si/Al = 19), especially at low-temperature regions (< 250 °C). In addition, it also exhibits better hydrothermal stability as compared with Fe-Beta (Si/Al = 19), which demonstrates that it is a promising SCR catalyst with good activity as well as hydrothermal stability. The correlation between the quantitative calculation of the content of isolated Fe3+ in Beta zeolites and the NO conversion rate at 150 °C shows a linear relationship, suggesting that the isolated Fe3+ species affect the SCR activity directly. The higher activity of the Fe-Beta-9 catalyst is supposed to be related not only to the isolated Fe3+ but also to the acidity. Furthermore, the template-free synthesized Beta zeolite shows less dealumination during hydrothermal aging and therefore better hydrothermal stability during the SCR reaction. © 2016 The Royal Society of Chemistry.

A comprehensive microkinetic model, including catalyst descriptors, that accounts for the homogeneous as well as heterogeneously catalyzed reaction steps in Oxidative Coupling of Methane (OCM) was used in the assessment of large kinetic datasets acquired on five different catalytic materials. The applicability of the model was extended from alkali magnesia catalysts represented by Li/MgO and Sn-Li/MgO and alkaline earth lanthana catalysts represented by Sr/La2O3 to rare earth-promoted alkaline earth calcium oxide catalysts, represented by LaSr/CaO, and to a Na-Mn-W/SiO2 catalyst. The model succeeded in adequately simulating the performance of all five investigated catalysts in terms of reactant conversion and product selectivities in the entire range of experimental conditions. It was found that the activity of Sr/La2O3, in terms of methane conversion, is approximately 2, 5, 30 and 33 times higher than over the La-Sr/CaO, Sn-Li/MgO, Na-Mn-W/SiO2 and Li/MgO catalysts, respectively, under identical operating conditions. This was attributed mainly to the high stability of adsorbed hydroxyls, the high stability of adsorbed oxygen and the high concentration of active sites of Sr/La2O3. The selectivity towards C2 products was found to depend on the methyl radical sticking coefficient and the stability of the adsorbed oxygen and was the highest on the Na-W-Mn/SiO2 catalyst, that is 75% at about 1% methane conversion and 1023 K, 190 kPa and inlet molar CH4/O2 ratio of 4. © 2016 The Author(s)

The recombination of photogenerated electron-hole pairs is one of the main limiting factors of photoelectrocatalysts absorbing in the visible part of the solar spectrum. Especially for BiVO4 the slow electron transport to the back contact facilitates charge recombination. Hence, thin layers have to be used to obtain higher photocurrents which are concomitantly only allow low absorption of the incident light. To address this limitation we have modified FTO substrates with Pt-nanoparticles before electrodepositing BiVO4. The Pt-nanoparticles decrease the overpotential for the electrodeposition of BiVO4, but more importantly they provide the basis for decreased charge recombination. Electrodeposited Mo-doped BiVO4 on Pt-nanoparticle modified FTO exhibits a substantially decreased recombination of photogenerated charge carriers during frontside illumination. Simultaneous co-doping of BiVO4 with two different metals leads to a substantial enhancement of the incident-photon-to-current efficiency (IPCE) during light driven oxygen evolution reaction. Highest IPCE (>30% at 1.2 V vs. RHE) values were obtained for Mo/Zn- and Mo/B-doped BiVO4. © 2016 The Royal Society of Chemistry.

Electrochemical efficiency and stability are among the most important characteristics of electrocatalysts. These parameters are usually evaluated separately for the anodic and cathodic half-cell reactions in a three-electrode system or by measuring the overall cell voltage between the anode and cathode as a function of current or time. Here, we demonstrate how bipolar electrochemistry can be exploited to evaluate the efficiency of electrocatalysts for full electrochemical water splitting while simultaneously and independently monitoring the individual performance and stability of the half-cell electrocatalysts. Using a closed bipolar electrochemistry setup, all important parameters such as overvoltage, half-cell potential, and catalyst stability can be derived from a single galvanostatic experiment. In the proposed experiment, none of the half-reactions is limiting on the other, making it possible to precisely monitor the contribution of the individual half-cell reactions on the durability of the cell performance. The proposed approach was successfully employed to investigate the long-term performance of a bifunctional water splitting catalyst, specifically amorphous cobalt boride (Co2B), and the durability of the electrocatalyst at the anode and cathode during water electrolysis. Additionally, by periodically alternating the polarization applied to the bipolar electrode (BE) modified with a bifunctional oxygen electrocatalyst, it was possible to explicitly follow the contributions of the oxygen reduction (ORR) and the oxygen evolution (OER) half-reactions on the overall long-term durability of the bifunctional OER/ORR electrocatalyst. © 2016 American Chemical Society.

Dry reforming of methane (DRM) has been studied for many years as an attractive option to produce synthesis gas. However, catalyst deactivation by coking over nonprecious-metal catalysts still remains unresolved. Here, we study the influence of structural and compositional properties of nickel catalysts on the catalytic performance and coking propensity in the DRM. A series of bulk catalysts with different Ni contents was synthesized by calcination of hydrotalcite-like precursors NixMg0.67-xAl0.33(OH)2(CO3)0.17·mH2O prepared by constant-pH coprecipitation. The obtained Ni/MgAl oxide catalysts contain Ni nanoparticles with diameters between 7 and 20 nm. High-resolution transmission electron microscopy (HR-TEM) revealed a nickel aluminate overgrowth on the Ni particles, which could be confirmed by Fourier transform infrared (FTIR) spectroscopy. In particular, catalysts with low Ni contents (5 mol %) exhibit predominantly oxidic surfaces dominated by Ni2+ and additionally some isolated Ni0 sites. These properties, which are determined by the overgrowth, effectively diminish the formation of coke during the DRM, while the activity is preserved. A large (TEM) and dynamic (microcalorimetry) metallic Ni surface at high Ni contents (50 mol %) causes significant coke formation during the DRM. © 2016 American Chemical Society.

Direct catalytic methane functionalization, a "dream reaction", is typically characterized by relatively low catalyst activities. This also holds for the n2-(2,2′-bipyrimidyl)dichloroplatinum(II) [(bpym)PtCl2, 1] catalyst which oxidizes methane to methyl bisulfate in sulfuric acid. Nevertheless, it is arguably still one of the best systems for the partial oxidation of methane reported so far. Detailed studies of the dependence of activity on the SO3 concentration and the interplay with the solubility of different platinum compounds revealed potassium tetrachloroplatinate (K2PtCl4) as an extremely active, selective, and stable catalyst, reaching turnover frequencies (TOFs) of more than 25,000 h-1 in 20% oleum with selectivities above 98%. The TOFs are more than 3 orders of magnitude higher compared to the original report on (bpym)PtCl2 and easily reach or exceed those realized in commercial industrial processes, such as the Cativa process for the carbonylation of methanol. Also space-time-yields are on the order of large-scale commercialized processes. © 2016 American Chemical Society.

The role of the stability of surface functional groups in oxygen- and nitrogen-functionalized multi-walled carbon nanotubes (CNTs) applied as support for iron catalysts in high-temperature Fischer-Tropsch synthesis was studied in a fixed-bed U-tube reactor at 340°C and 25 bar with a H2:CO ratio of 1. Iron oxide nanoparticles supported on untreated oxygen-functionalized CNTs (OCNTs) and nitrogen-functionalized CNTs (NCNTs) as well as thermally treated OCNTs were synthesized by the dry impregnation method using ammonium ferric citrate as iron precursor. The properties of all catalysts were examined using X-ray diffraction, temperature-programmed reduction in H2, X-ray photoelectron spectroscopy and temperature-programmed oxidation in O2. The activity loss for iron nanoparticles supported on untreated OCNTs was found to originate from severe sintering and carbon encapsulation of the iron carbide nanoparticles under reaction conditions. Conversely, the sintering of the iron carbide nanoparticles on thermally treated OCNTs and untreated NCNTs during reaction was far less pronounced. The presence of more stable surface functional groups in both thermally treated OCNTs and untreated NCNTs is assumed to be responsible for the less severe sintering of the iron carbide nanoparticles during reaction. As a result, no activity loss for iron nanoparticles supported on thermally treated OCNTs and untreated NCNTs was observed, which even became gradually more active under reaction conditions. © 2015 Published by Elsevier B.V.

Due to the high cost of precious metal-based electrocatalysts for oxygen reduction and oxygen evolution, the development of alternative low cost and efficient catalysts is of high importance for energy storage and conversion technologies. Although non-precious catalysts that can efficiently catalyze oxygen reduction and oxygen evolution have been developed, electrocatalysts with high bifunctional activity for both oxygen evolution and reduction are needed. Perovskites based on modified lanthanum cobaltite possess significant activity for the oxygen evolution reaction. We describe the synthesis of a bifunctional oxygen electrode with simultaneous activity for the oxygen evolution reaction (OER) and the oxygen reduction reaction (ORR) in alkaline media by direct growth of nitrogen-doped carbon nanotubes on the surface of a perovskite containing Co and Fe by means of chemical vapor deposition. The difference in the overvoltage between ORR (at 1 mA/cm2) and OER (at 10 mA/cm2) was below 880 mV in 0.1 M KOH. The formation of H2O2 during the ORR was reduced by at least three fold when using the bifunctional catalyst as compared to the non-modified perovskite. Long-term durability tests indicate stable performance for at least 37 h during the OER and 23 h during the ORR. © 2016 Elsevier Ltd. All rights reserved.

A size-dependent trend was observed for the electrochemical total oxidation of 2-propanol to CO2 over Au nanoparticles (NPs), with increasing activity (increased current density and lower overpotential) for decreasing NP size. Furthermore, an enhanced stability against poisoning by the unreacted acetone intermediate was also obtained for NPs smaller than ∼2 nm. Operando X-ray absorption fine structure (XAFS) measurements provided insight into the dynamic evolution of the NP structure and chemical state under reaction conditions, shedding light on the nature of the most catalytically active species and catalyst deactivation phenomena via chemically driven sintering. © 2016 American Chemical Society.

The desorption kinetics of hydrogen from a polycrystalline Cu/ZrO2 catalyst was investigated under atmospheric pressure using temperature-programmed desorption (TPD) experiments in a microreactor set-up. Different heating rates were applied under equal conditions with a carefully reduced catalyst. The hydrogen TPD peaks were symmetric and centered slightly above 300 K indicating associative desorption of H2 from metallic Cu. Using heating rate variation, the kinetic parameters Ades and Edes were determined to be 1.24 × 109 s-1 and 68 kJ mol-1, respectively. As the modeling with constant values of Ades and Edes yielded signals which were too narrow, dependence of Edes on coverage was introduced applying Edes - K (ΘH)n. By application of the "full-analysis" method an optimal fit to the experimental data was found. Setting n = 1 resulted in the best fit and a value of 61 kJ mol-1 - (6.25 kJ mol-1 × ΘH) for Edes was determined. © Springer Science+Business Media New York 2016.

The selectivity of heterogeneously catalyzed chemical reactions is well-known to be dependent on nanoscale determinants, such as surface atomic geometry and composition. However, principles to control the selectivity of nanoparticle (NP) catalysts by means of mesoscopic descriptors, such as the interparticle distance, have remained largely unexplored. We used well-defined copper catalysts to deconvolute the effect of NP size and distance on product selectivity during CO2 electroreduction. Corroborated by reaction-diffusion modeling, our results reveal that mesoscale phenomena such as interparticle reactant diffusion and readsorption of intermediates play a defining role in product selectivity. More importantly, this study uncovers general principles of tailoring NP activity and selectivity by carefully engineering size and distance. These principles provide guidance for the rational design of mesoscopic catalyst architectures in order to enhance the production of desired reaction products. © 2015 American Chemical Society.

It is demonstrated that amorphous cobalt boride (Co2B) prepared by the chemical reduction of CoCl2 using NaBH4 is an exceptionally efficient electrocatalyst for the oxygen evolution reaction (OER) in alkaline electrolytes and is simultaneously active for catalyzing the hydrogen evolution reaction (HER). The catalyst achieves a current density of 10 mA cm(-2) at 1.61 V on an inert support and at 1.59 V when impregnated with nitrogen-doped graphene. Stable performance is maintained at 10 mA cm(-2) for at least 60 h. The optimized catalyst, Co2B annealed at 500 degrees C (Co2B-500) evolves oxygen more efficiently than RuO2 and IrO2, and its performance matches the best cobalt-based catalysts reported to date. Co2B is irreversibly oxidized at OER conditions to form a CoOOH surface layer. The active form of the catalyst is therefore represented as CoOOH/Co2B. EXAFS observations indicate that boron induces lattice strain in the crystal structure of the metal, which potentially diminishes the thermodynamic and kinetic barrier of the hydroxylation reaction, formation of the OOH* intermediate, a key limiting step in the OER.

The field of electrocatalysis has undergone tremendous advancement in the past few decades, in part owing to improvements in catalyst design at the nanoscale. These developments have been crucial for the realization of and improvement in alternative energy technologies based on electrochemical reactions such as fuel cells. Through the development of novel synthesis methods, characterization techniques and theoretical methods, rationally designed nanoscale electrocatalysts with tunable activity and selectivity have been achieved. This Review explores how nanostructures can be used to control electrochemical reactivity, focusing on three model reactions: O-2 electroreduction, CO2 electroreduction and ethanol electrooxidation. The mechanisms behind nanoscale control of reactivity are discussed, such as the presence of low-coordinated sites or facets, strain, ligand effects and bifunctional effects in multimetallic materials. In particular, studies of how particle size, shape and composition in nanostructures can be used to tune reactivity are highlighted.

The efficiency of the direct electrochemical CO2 reduction can be improved by the development of new alloy catalysts, but to do so a highly resolved composition screening remains to be connected to complex sample preparation and time consuming analysis. We have developed a technique that allows a fast and easy initial catalyst composition screening by analyzing thin film composition spread samples, utilizing a scanning flow cell coupled to an online electrochemical mass spectrometer (SFC-OLEMS). As a first case example, the investigation of a Cu–Co thin film material library demonstrates the benefits and high potential of this approach. In particular, a shift in selectivity toward C2 species for low Co content (5–15 at.%) has been found and is discussed as being related to changed adsorption energies of intermediate products and the consequent modification of reaction pathways. © 2016 Elsevier Inc.

There is an urgent need to develop technologies that use renewable energy to convert waste products such as carbon dioxide into hydrocarbon fuels. Carbon dioxide can be electrochemically reduced to hydrocarbons over copper catalysts, although higher efficiency is required. We have developed oxidized copper catalysts displaying lower overpotentials for carbon dioxide electroreduction and record selectivity towards ethylene (60%) through facile and tunable plasma treatments. Herein we provide insight into the improved performance of these catalysts by combining electrochemical measurements with microscopic and spectroscopic characterization techniques. Operando X-ray absorption spectroscopy and cross-sectional scanning transmission electron microscopy show that copper oxides are surprisingly resistant to reduction and copper+ species remain on the surface during the reaction. Our results demonstrate that the roughness of oxide-derived copper catalysts plays only a partial role in determining the catalytic performance, while the presence of copper+ is key for lowering the onset potential and enhancing ethylene selectivity.

The need for sustainable catalysts for an efficient hydrogen evolution reaction is of significant interest for modern society. Inspired by comparable structural properties of [FeNi]-hydrogenase, here we present the natural ore pentlandite (Fe 4.5 Ni 4.5 S 8) as a direct rock' electrode material for hydrogen evolution under acidic conditions with an overpotential of 280 mV at 10 mA cm -2. Furthermore, it reaches a value as low as 190 mV after 96 h of electrolysis due to surface sulfur depletion, which may change the electronic structure of the catalytically active nickel-iron centres. The rock' material shows an unexpected catalytic activity with comparable overpotential and Tafel slope to some well-developed metallic or nanostructured catalysts. Notably, the rock' material offers high current densities (≤650 mA cm -2) without any loss in activity for approximately 170 h. The superior hydrogen evolution performance of pentlandites as rock' electrode labels this ore as a promising electrocatalyst for future hydrogen-based economy.

A simple and scalable method for synthesizing Co3O4nanoparticles supported on the framework of mesoporous carbon (MC) was developed. Benefiting from an ion-exchange process during the preparation, the cobalt precursor is introduced into a mesostructured polymer framework that results in Co3O4nanoparticles (ca. 3 nm) supported on MC (Co3O4/MC) with narrow particle size distribution and homogeneous dispersion after simple reduction/pyrolysis and mild oxidation steps. The as-obtained Co3O4/MC is a highly efficient catalyst for transfer hydrogenation of α,β-unsaturated aldehydes. Selectivities towards unsaturated alcohols are always higher than 95 % at full conversion. In addition, the Co3O4/MC shows high stability under the reaction conditions, it can be recycled at least six times without loss of activity. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Efficient reversible oxygen electrodes for both the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) are vitally important for various energy conversion devices, such as regenerative fuel cells and metal-air batteries. However, realization of such electrodes is impeded by insufficient activity and instability of electrocatalysts for both water splitting and oxygen reduction. We report highly active bifunctional electrocatalysts for oxygen electrodes comprising core-shell Co@Co3O4 nanoparticles embedded in CNT-grafted N-doped carbon-polyhedra obtained by the pyrolysis of cobalt metal-organic framework (ZIF-67) in a reductive H2 atmosphere and subsequent controlled oxidative calcination. The catalysts afford 0.85 V reversible overvoltage in 0.1 m KOH, surpassing Pt/C, IrO2, and RuO2 and thus ranking them among one of the best non-precious-metal electrocatalysts for reversible oxygen electrodes. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nature's subtle systems drive essential reactions responsible for sustenance of our existence “reactions of life” through sophisticated mechanisms of charge transfer, energy harvest and conversion. The interconnectedness between living nature and technologically relevant electrochemical reactions, for example, oxygen reduction and evolution catalyzed by cytochrome c oxidases and photosystem II respectively, and hydrogen oxidation and evolution catalyzed by hydrogenases, does not only intrigue but also inspires us. To what extent therefore can our present understanding of electrocatalysis guide us to decipher nature's sophistication, or rather, can bioinspired electrocatalysis succeed to replicate and supersede nature's perfection “the exemplar paragon”? Herein, we present a harmonized perspective of the principle factors which govern electrocatalysis and bioelectrocatalysis featuring examples of technologically important electrochemical reactions catalyzed by both enzymes and inorganic electrocatalysts. Sound knowledge of the inter-relationships linking electrocatalysis and bioelectrocatalysis is essential for enabling a deeper understanding of nature's bioelectrochemical reactions, and for insightful design of functional catalysts inspired by models from living nature. © 2016 Elsevier Ltd

Cu–Co-based catalysts derived from hydrotalcite (HT)-type precursors were applied in higher alcohol synthesis (HAS) at 280 °C, 60 bar and a H2/CO ratio of 1/1. Catalysts with higher Cu/Co ratios were found to provide the best trade-off between selective alcohol formation and moderate Fischer–Tropsch synthesis (FTS) activity. Within the alcohols and hydrocarbons formed the productivities decreased exponentially with increasing chain length according to the ASF distribution indicating a chain growth mechanism. Thermal analysis revealed the presence of different bivalent cations in one single HT-type precursor phase. After calcination at lower temperatures (Tcalc <  600 °C) a carbonate-modified ZnAl2O4 matrix was obtained. Within this amorphous matrix Cu2+ and Co2+ were found to be partially embedded resulting in an impeded ion reduction. After HAS the presence of bulk Co2C was detected by XRD. Both close contact of Cu0 and Co0 as well as Co2C–Co0 interfaces are known to provide the mechanistic requirements for higher alcohol formation. For comparison HAS was performed over a physical mixture consisting of the Al-containing HTs of Cu, Co or Zn. For the simultaneously co-precipitated samples the major roles of Cu are to decrease the FTS activity of metallic Co and to lower the alcohol chain growth probability by intimate Cu0–Co0 interactions. With increasing Cu content the alcohol selectivities were found to increase at the expense of high conversion, with ethanol being the major oxygenate product for all HT-based catalysts. © 2016, Springer Science+Business Media New York.

The redox competition mode of scanning electrochemical microscopy (SECM) was used to visualize differences in local electrocatalytic activity of Fe and Ni hexacyanoferrates (HCFs) in hydrogen peroxide reduction. The uniform round-shaped spots of electrocatalysts for the SECM measurements were electrochemically deposited using a scanning droplet cell. A negligible activity of NiHCF towards H2O2 reduction compared to Prussian Blue (PB) was observed. The dependence of local Prussian Blue activity on the applied potential was investigated. The proposed strategy explores the potential application of SECM as a rapid screening tool for HCF film activity within a single experiment. © 2016, Pleiades Publishing, Ltd.

The (1 1 1)-layered perovskite material Ba5Ta4O15 represents a suitable photoabsorber with remarkable photocatalytic activity in overall water splitting. We are the first to demonstrate overall water splitting without the presence of a noble-metal-based co-catalyst over this catalyst. The photocatalytic activity of Ba5Ta4O15 was investigated by overall water splitting after reductive photodeposition of amorphous Cr2O3. The formation of Cr2O3 nanoparticles for water splitting was evidenced by X-ray photoelectron spectroscopy and transmission electron microscopy. The reductive photodeposition of very low amounts of Cr2O3 on Ba5Ta4O15 induces stable rates in overall water splitting up to 465 μmol h-1 H2 and 228 μmol h-1 O2. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Large scale commercialization of direct ethanol fuel cells is hampered by the high cost and scarcity of noble metal electrocatalysts employed at both the anode and cathode. We demonstrate improved utilization of palladium as anode catalyst for ethanol oxidation by exploiting the strong interaction between Pd nanoparticles and nitrogen-doped carbon nanotubes (NCNTs) as support. 0.85 wt% Pd supported on NCNTs achieved a specific current density of 517 A gPd - 1 compared with 421 A gPd - 1 for 0.86 wt% Pd on oxygen-functionalized carbon nanotubes. The electrocatalytic performance deteriorated only gradually and catalysis was sustained for at least 80 h. © 2015 Elsevier B.V. All rights reserved.

Oxide materials are among the state-of-the-art heterogeneous electrocatalysts for many important large-scale industrial processes, including O2 and Cl2 evolution reactions. However, benchmarking their performance is challenging in many cases, especially at high current densities, which are relevant for industrial applications. Serious complications arise particularly due to (i) the formation of a nonconducting gas phase which blocks the surface during the reactions, (ii) problems in determination of the real electroactive electrode area, and (iii) the large influence of surface morphology alterations (stability issues) under reaction conditions, among others. In this work, an approach overcoming many of these challenges is presented, with a focus on electrochemically formed thin-film oxide electrocatalysts. The approach is based on benefits provided by the use of microelectrodes, and it gives comprehensive information about the surface roughness, catalyst activity, and stability. The key advantages of the proposed method are the possibility of characterization of the whole microelectrode surface by means of atomic force microscopy and an accurate assessment of the specific activity (and subsequently stability) of the catalyst, even at very high current densities. Electrochemically deposited CoOx thin films have been used in this study as model catalysts. © 2016 American Chemical Society.

Low-cost electrocatalysts based on highly dispersed molybdenum carbide supported on carbon nanotubes (CNTs) were developed for the hydrogen evolution reaction (HER). The synthesis of MoxC/CNT was achieved by impregnation using ammonium heptamolybdate followed by a thermal treatment at 700 °C in CH4/H2, H2 or N2. The composites were characterized by X-ray diffraction, N2 physisorption, and X-ray photoelectron spectroscopy. β-Mo2C was the main Mo carbide phase generated in N2 or H2, whereas α-MoC was the dominant phase formed in CH4/H2. All the MoxC/CNT composites were catalytically active in the HER under alkaline conditions. The catalyst pretreated in pure H2 exhibited the highest HER activity, which was found to correlate with a higher amount of Mo2C, a higher total Mo content and a higher Mo surface concentration compared with the other two less active samples. Amorphous carbon on the surface seems to play an important role in limiting the HER performance of the Mo carbide catalysts, and the treatment in H2 removed it most effectively leading to high HER activity. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

Electrocatalysts that can reversibly reduce oxygen and oxidise water are of prime importance for the advancement of new emerging electrochemical energy storage and conversion systems. We present in this work the application of scanning electrochemical microscopy (SECM) for characterisation of bifunctional catalysts. By using model bifunctional catalysts based on oxides of cobalt (CoxOy) and nickel (NixOy) embedded in nitrogen-doped carbon (NC), we specifically show the unique ability of using SECM to determine a range of the important electrocatalytic parameters including the selectivity of the oxygen reduction reaction (ORR), the initial mechanistic steps during the oxygen evolution reaction (OER), and the onset potential for both ORR and OER in a single experiment. We were able to observe directly that prior to oxygen evolution, local depletion of oxygen occurs at the SECM tip during redox transition accompanying most likely metal oxyhydroxide formation thus enabling direct in situ observation of the initial mechanistic steps of the OER. © 2015, Springer-Verlag Berlin Heidelberg.

Non-noble metal based materials efficiently catalyzing the hydrogen evolution reaction (HER) are reported based on a novel strategy where electrocatalytically active ultrathin molybdenum sulphoselenide sheets are incorporated into electrically conducting reduced graphene oxide sheets via a self-assembly approach. By taking advantage of the electrostatic attraction between the two oppositely charged nanosheets, MoSSe@rGO composite materials are obtained exhibiting superior electrocatalytic activity and stability for the HER allowing a current density of 5 mA cm−2 at a low overpotential of only 135 mV. These findings pave the way to novel electrocatalysts based on composites of MoSSe and reduced graphene oxide towards the design of ultra-light, mechanically robust and electrically conductive electrode materials for electrocatalytic water splitting. © 2016 Elsevier Ltd

Combining advantages of homogeneous and heterogeneous catalysis by incorporating active species on a solid support is often an effective strategy for improving overall catalyst performance, although the influences of the support are generally challenging to establish, especially at a molecular level. Here, we report the local compositions, and structures of platinum species incorporated into covalent triazine framework (Pt-CTF) materials, a solid analogue of the molecular Periana catalyst, Pt(bpym)Cl2, both of which are active for the selective oxidation of methane in the presence of concentrated sulfuric acid. By using a combination of solid-state 195Pt nuclear magnetic resonance (NMR) spectroscopy, aberration-corrected scanning transmission electron microscopy (AC-STEM), X-ray photoelectron spectroscopy (XPS), and X-ray absorption spectroscopy (XAS), important similarities and differences are observed between the Pt-CTF and Periana catalysts, which are likely related to their respective macroscopic reaction properties. In particular, wide-line solid-state 195Pt NMR spectra enable direct measurement, identification, and quantification of distinct platinum species in as-synthesized and used Pt-CTF catalysts. The results indicate that locally ordered and disordered Pt sites are present in as-synthesized Pt-CTF, with the former being similar to one of the two crystallographically distinct Pt sites in crystalline Pt(bpym)Cl2. A distribution of relatively disordered Pt moieties is also present in the used catalyst, among which are the principal active sites. Similarly XAS shows good agreement between the measured data of Pt-CTF and a theoretical model based on Pt(bpym)Cl2. Analyses of the absorption spectra of Pt-CTF used for methane oxidation suggests ligand exchange, as predicted for the molecular catalyst. XPS analyses of Pt(bpym)Cl2, Pt-CTF, as well as the unmodified ligands, further corroborate platinum coordination by pyridinic N atoms. Aberration-corrected high-angle annular dark-field STEM proves that Pt atoms are distributed within Pt-CTF before and after catalysis. The overall results establish the close similarities of Pt-CTF and the molecular Periana catalyst Pt(bpym)Cl2, along with differences that account for their respective properties. (Figure Presented). © 2016 American Chemical Society.

This study focuses on the synthesis and electrochemical performance (i.e, activity and stability) of advanced electrocatalysts for the oxygen reduction reaction (ORR), made of Pt-Ni nanoparticles embedded in hollow graphitic spheres (HGS). The mechanism of the confined space alloying, that is, the controlled alloying of bimetallic precursors with different compositions (i.e., Pt3Ni, PtNi, and PtNi3) within the HGS mesoporous shell, was examined in detail. It was found that the presence of platinum during the reduction step, as well as the application of high annealing temperatures (at least 850°C for 3.5h in Ar), are necessary conditions to achieve the complete encapsulation and the full stability of the catalysts. The evolution of the activity, the electrochemical surface area, and the residual alloy composition of the Pt-Ni@HGS catalysts was thoroughly monitored (at the macro- and nanoscale level) under different degradation conditions. After the initial activation, the embedded Pt-Ni nanoparticles (3-4 nm in size) yield mass activities that are 2- to 3.5-fold higher than that of pure Pt@HGS (depending on the alloy composition). Most importantly, it is demonstrated that under the normal operation range of an ORR catalyst in PEM-FCs (potential excursions between 0.4 and 1.0 VRHE) both the nanoparticle-related degradation pathways (particle agglomeration) and dealloying phenomena are effectively suppressed, irrespectively of the alloy composition. Thus, the initial enhanced activity is completely maintained over an extended degradation protocol. In addition, owing to the peculiar configuration of the catalysts consisting of space-confined nanoparticles, it was possible to elucidate the impact of the dealloying process (as a function of alloy composition and severity of the degradation protocols) separately from other parallel phenomena, providing valuable insight into this elusive degradation mechanism. (Graph Presented). © 2016 American Chemical Society.

Hydrodeoxygenation (HDO) is an attractive route for the upgrading of bio-oils produced from lignocellulose. Current catalysts require harsh conditions to effect HDO, decreasing the process efficiency in terms of energy and carbon balance. Herein we report a novel and facile method for synthesizing bimetallic PtCo nanoparticle catalysts (ca. 1.5 nm) highly dispersed in the framework of nitrogen-doped ordered mesoporous carbon (NOMC) for this reaction. We demonstrate that NOMC with either 2D hexagonal (p6m) or 3D cubic (Im3m) structure can be easily synthesized by simply adjusting the polymerization temperature. We also demonstrate that PtCo/NOMC (metal loading: Pt 9.90 wt %; Co 3.31 wt %) is a highly effective catalyst for HDO of phenolic compounds and “real-world” biomass-derived phenolic streams. In the presence of PtCo/NOMC, full deoxygenation of phenolic compounds and a biomass-derived phenolic stream is achieved under conditions of low severity. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

The single-step production of wax-free liquid hydrocarbons from syngas (H2 + CO) via integration of Fischer-Trospch (FT) and hydrocracking catalysts represents an attractive approach toward process intensification in compact gas-to-liquid technologies. Despite current, intensive efforts on the development of hybrid (multifunctional) catalysts to this end, not much is known about the reactivity of different FT primary products on hydrocracking catalysts under syngas. Using model compounds, the individual and collective reactivities of n-paraffin and α-olefin FT primary products were systematically studied on a Pt/nano-H-ZSM-5 hydrocracking catalyst under H2 (standard hydrocracking) and syngas (in situ hydroprocessing) atmospheres. Under H2, both reactants show indistinguishable reactivity as rapid olefin hydrogenation precedes hydrocracking. Under syngas, however, inhibition of (de)hydrogenation functionalities by CO poisoning of metal sites leads to a notable divergence of the reaction pathways for n-paraffins and α-olefins. Under these conditions, α-olefins showed enhanced reactivity, as an initial dehydrogenative activation step is not required, and contributed to moderate secondary cracking, likely via enhanced competitive adsorption on the acid sites. Besides, CO poisoning restored the intrinsic activity of the zeolite for the oligomerization of short-chain (α-)olefins, providing an additional net chain-growth pathway, which contributes to reducing the overall yield to undesired gas (C4-) hydrocarbons. These findings emphasize the key role of not only the chain-length distribution, but also the olefinic content of the FT primary hydrocarbons for the ultimate product distribution, and suggest guidelines for the design of multifunctional catalysts for the single-step synthesis of liquid hydrocarbons from syngas. © 2016 American Chemical Society.

Understanding the redox properties of metal oxide based catalysts is a major task in catalysis research. In situ electron paramagnetic resonance (EPR) spectroscopy is capable of monitoring the change of metal ion valences and formation of active sites during redox reactions, allowing for the identification of ongoing redox pathways. Here in situ EPR spectroscopy combined with online gas analysis, supported by ex situ X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), X-ray absorption near edge structure (XANES), temporal analysis of product (TAP), and mass spectrometry (MS) studies, was utilized to study the redox behavior of CuO-CeO2 catalysts under PROX conditions (preferential oxidation of carbon monoxide in hydrogen). Two redox mechanisms are revealed: (i) a synergetic mechanism that involves the redox pair Ce4+/Ce3+ during oxidation of Cu0/Cu+ species to Cu2+ and (ii) a direct mechanism that bypasses the redox pair Ce4+/Ce3+. In addition, EPR experiments with isotopically enriched 17O2 established the synergetic mechanism as the major redox reaction pathway. The results emphasize the importance of the interactions between Cu and Ce atoms for catalyst performance. With the guidance of these results, an optimized CuO-CeO2 catalyst could be designed. A rather wide temperature operation window of 11 K (from 377 to 388 K), with 99% conversion efficiency and 99% selectivity, was achieved for the preferential oxidation of CO in a H2 feed. © 2016 American Chemical Society.

Zeolites synthesized without any organic structure-directing agent (OSDA) have several advantages over conventional zeolites synthesized with OSDAs. Their Al-rich compositions, however, are sometimes not suitable for applications as catalysts. In the present study, post-synthetic modification was performed using an Al-rich Beta zeolite synthesized without any OSDAs (designated as "Beta(OF)") to obtain high-silica Beta zeolites. We have successfully developed a facile post-synthetic method for tuning the Al content of Beta(OF) with the ∗BEA-type structure retained by calcination at >750 °C followed by acid treatment. Solid-state 29Si and 27Al MAS NMR analyses revealed that during calcination, framework Al atoms were isomorphously substituted with Si atoms to form high-silica frameworks and concomitant extra-framework Al species. The stability of the obtained frameworks against acid treatment was evaluated in terms of the framework Al content, finding that the framework with the Si/Al ratio higher than 12 is well stabilized enough for acid treatment. Thus, dealuminated Beta(OF) zeolites with high-silica compositions were found to be effective catalysts for the methanol-to-olefin (MTO) reaction; particularly, the Beta zeolite with the Si/Al ratio of 112 maintained the conversion of methanol over 90% with selectivity to C2-C4 olefins over 70% even at 40 hours on stream at WHSV = 3.2 h-1. © The Royal Society of Chemistry 2016.

We propose a method for the formation of highly active bifunctional oxygen electrocatalysts, by exploiting the unique features of nitrogen-rich metallo-macrocyclic complexes and the structural and electronic properties of few-layer graphene. The precursors of the electrocatalysts were synthesized by sonication of graphite in DMF leading to exfoliation and the formation of few-layer graphene sheets in the presence of a suitable transition metal macrocyclic complex. After pyrolysis and subsequent mild calcination metal oxide nanoparticles as well as metal-nitrogen (MNx) moieties embedded within a N-doped graphitic carbon matrix are obtained. The formation, in-depth characterization and electrochemical performance of two different catalysts derived from Co and Ni containing precursor complexes are demonstrated. © 2016 Elsevier Ltd

Gold nanoparticles (NPs) synthesized by pulsed laser ablation of a gold target in water were efficiently deposited on TiO2 (P25) without any post-treatment yielding catalysts with Au loadings up to 10 wt%. Regardless of the loading, the Au NPs had a mean diameter of 8 nm before and after deposition. The ligand-free Au NPs strongly bind to TiO2 surface oxygen vacancies and maintain a homogeneous distribution with loadings up to 4 wt%, while a further increase in Au content up to 10 wt% results in additional weakly adsorbed Au NPs. The catalytic tests of the Au/TiO2 samples in the selective oxidation of ethanol in the liquid phase identified an optimal loading of 4 wt% resulting in the highest yield of acetic acid, which is ascribed to the homogeneous Au distribution and the adequate occupation of surface oxygen vacancies by strongly bound Au NPs without significant Au sintering during reaction. © 2015 Elsevier Inc. All rights reserved.

The onset potential of an electrocatalytic reaction is frequently used as an indicator to compare the catalytic performance of electrocatalysts. However, in addition to the fact that the onset potential is an undefined physico-chemical value which is dependent on the sensitivity of the used potentiostat its determination using voltammetry at the catalyst-modified electrode surface may be superimposed by additional Faradaic reactions e.g. from redox conversions of the catalyst material or corrosion processes. Gas-evolving electrodes suffer additionally from the dynamics of gas bubble formation and departure leading to inherent limitations of voltammetric studies directly performed at the catalyst-modified electrode. Nanometer-sized electrodes accurately positioned by means of shearforce-based constant-distance mode SECM are proposed for the highly sensitive determination of the onset potential of microcavity electrodes filled with different perovskites as oxygen evolution catalysts. Double barrel microcavity electrodes are additionally suggested for the simultaneous investigation of two catalysts. They enable direct referencing of a catalyst with a benchmark catalyst material in a single experiment. © 2015 Elsevier Ltd. All rights reserved.

In recent years, the field of catalysis has experienced an astonishing transformation, driven in part by more demanding environmental standards and critical societal and industrial needs such as the search for alternative energy sources. Thanks to the advent of nanotechnology, major steps have been made towards the rational design of novel catalysts. Striking new catalytic properties, including greatly enhanced reactivities and selectivities, have been reported for nanoparticle (NP) catalysts as compared to their bulk counterparts. However, in order to harness the power of these nanocatalysts, a detailed understanding of the origin of their enhanced performance is needed. The present review focuses on the role of the NP size and shape on chemisorption and catalytic performance. Since homogeneity in NP size and shape is a prerequisite for the understanding of structure-reactivity correlations, we first review different synthesis methods that result in narrow NP size distributions and shape controlled NPs. Next, size-dependent phenomena which influence the chemical reactivity of NPs, including quantum size-effects and the presence of under-coordinated surface atoms are examined. The effect of the NP shape on catalytic performance is discussed and explained based on the existence of different atomic structures on the NP surface with distinct chemisorption properties. The influence of additional factors, such as the oxidation state of the NPs and NP-support interactions, is also considered in the frame of the size- and shape-dependency that these phenomena present. Ultimately, our review highlights the importance of achieving a systematic understanding of the factors that control the activity and selectivity of a catalyst in order to avoid trial and error methods in the rational design of the new generation of nanocatalysts with properties tunable at the atomic level. © 2015 Elsevier B.V. All rights reserved.

The photocatalytic properties of different calcium tantalate nanocomposite photocatalysts with optimized phase composition were studied without the addition of any co-catalysts in the photoreforming of different alcohols including the biomass conversion by-product glycerol, as well as after modification with double-layered NiOx (Ni/NiO) co-catalyst in overall water splitting (OWS). Nanocomposite photocatalyst consisting of cubic α-CaTa2O6/orthorhombic β-CaTa2O6 coexisting phases always possesses the highest photocatalytic performance. For overall water splitting, a loading of 0.5 wt. % NiOx exhibits the best activities with stable stoichiometric H2 and O2 evolution rates. © 2015 Author(s).

Uniform Au nanoparticles (∼2 nm) with narrow size-distribution (standard deviation: 0.5-0.6 nm) supported on both hydroxylated (Fe-OH) and dehydrated iron oxide (Fe-O) have been prepared by either deposition-precipitation (DP) or colloidal-deposition (CD) methods. Different structural and textural characterizations were applied to the dried, calcined and used gold-iron oxide samples. Transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) showed high homogeneity in the supported Au nanoparticles. The ex situ and in situ X-ray absorption fine structure (XAFS) characterization monitored the electronic and short-range local structure of active gold species. The synchrotron-based in situ X-ray diffraction (XRD), together with the corresponding temperature-programmed reduction by hydrogen (H2-TPR), indicated a structural evolution of the iron-oxide supports, correlating to their reducibility. An inverse order of catalytic activity between DP (Au/Fe-OH < Au/Fe-O) and CD (Au/Fe-OH > Au/Fe-O) was observed. Effective gold-support interaction results in a high activity for gold nanoparticles, locally generated by the sintering of dispersed Au atoms on the oxide support in the DP synthesis, while a hydroxylated surface favors the reactivity of externally introduced Au nanoparticles on Fe-OH support for the CD approach. This work reveals why differences in the synthetic protocol translate to differences in the catalytic performance of Au/FeOx catalysts with very similar structural characteristics in CO oxidation. © The Royal Society of Chemistry 2015.

We provide a comprehensive durability assessment dedicated to a promising class of electrocatalysts for the oxygen reduction reaction (i.e., porous platinum nanoparticles). The stability of these nanoengineered open structures is tested under two accelerated degradation test conditions (ADT), particularly selected to mimic the potential regimes experienced by the catalyst during the operative life of a fuel cell (i.e., load cycles (up to 1.0 VRHE) and start-up cycles (up to 1.4 VRHE)). To understand the evolution of the electrochemical performance, the catalyst properties are investigated by means of fundamental rotating disc electrode studies, identical location-transmission electron microscopy (IL-TEM) coupled with electron energy loss spectroscopy chemical mapping (IL-EELS), and post-use chemical analysis and online highly sensitive potential resolved dissolution concentration monitoring by scanning flow cell inductively coupled plasma-mass spectrometry (SFC-ICP-MS). The experimental results on the nanoporous Pt revealed distinctive degradation mechanisms that could potentially affect a wide range of other nanoengineered open structures. The study concludes that, although providing promising activity performance, under the relevant operational conditions of fuel cells, the nanoporosity is only metastable and subjected to a progressive reorganization toward the minimization of the nanoscale curvature. The rate and pathways of this specific degradation mechanism together with other well-known degradation mechanisms like carbon corrosion and platinum dissolution are strongly dependent on the selected upper limit potential, leading to distinctly different durability performance. © 2015 American Chemical Society.

Multiwalled carbon nanotubes (CNTs) functionalized by oxygen plasma were used as a support for platinum-ruthenium nanoparticles for electrochemical methanol oxidation. The influence of plasma treatment time on the electrocatalytic activity was investigated by cyclic voltammetry, CO stripping voltammetry, and chronoamperometry. The electrocatalysts were characterized by Raman spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results showed that oxygen plasma treatment led to the formation of -CO and -COO groups on the CNT surface. Platinum-ruthenium nanoparticles dispersed with an optimum plasma treatment time of 30 min exhibited the maximum catalytic activity towards methanol oxidation. The rationale for the high catalytic activity is discussed. © 2015 Wiley-VCH Verlag GmbH & Co. KGaA.

A synergetic interplay: Catalysis is a key research field within BASF. Successful industrial chemistry is always the result of a combination of catalyst and process development. The interplay of catalyst chemistry and reaction engineering is discussed for processes such as the sulfuric acid production, ammonia synthesis, methanol synthesis, fluid catalytic cracking, and direct epoxidation of propylene. (Figure Presented). © 2015 Wiley-VCH Verlag GmbH & Co. KGaA.

Better understanding of the factors responsible for the long-term stability of electrocatalysts is of increasing importance for the development of new generations of efficient electrode materials relevant for sustainable energy provision. Therefore, experiments with model, often single-crystal catalytic surfaces are of significance for fundamental electrochemistry and technological applications. Among model electrocatalysts, near-surface alloys (NSAs) of Pt with Cu, Ni and other metals formed via electrochemical deposition and thermal annealing have shown remarkable properties, demonstrating high activity towards a number of important reactions, including the oxygen reduction reaction (ORR) and CO oxidation. However, relatively little is known about the electrochemical stability and mechanisms of degradation of model NSAs. In this work, we employ a simple electrochemical approach, supported by density functional theory calculations, to evaluate the stability of Cu-Pt(111) NSAs in 0.1 M HClO4. Our results show that ∼30% of the Cu atoms initially incorporated into the second atomic layer of Pt are lost within the first 2000 cycles performed between 0.05 V and 1.0 V (RHE). After 5000 cycles, ca. half of the Cu atoms initially placed in the second atomic layer still remained in the subsurface region. The dissolution of Cu has a substantial impact on the measured shift in the average OH-binding energy for the catalyst surface and, consequently, on the ORR activity. Interestingly, after dissolution of Cu from NSAs, voltammetric features, which are characteristic to the Pt(111) facets, are partially restored suggesting the formation of NSA and Pt(111) domains in the resulting surface. © 2015 Elsevier Ltd. All rights reserved.

The notion of metal-free catalysts is used to refer to carbon materials modified with nonmetallic elements. However, some claimed metal-free catalysts are prepared using metal-containing precursors. It is highly contested that metal residues in nitrogen-doped carbon (NC) catalysts play a crucial role in the oxygen reduction reaction (ORR). In an attempt to reconcile divergent views, a definition for truly metal-free catalysts is proposed and the differences between NC and M-Nx/C catalysts are discussed. Metal impurities at levels usually undetectable by techniques such as XPS, XRD, and EDX significantly promote the ORR. Poisoning tests to mask the metal ions reveal the involvement of metal residues as active sites or as modifiers of the electronic structure of the active sites in NC. The unique merits of both M-Nx/C and NC catalysts are discussed to inspire the development of more advanced nonprecious-metal catalysts for the ORR. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The use of synthetic inorganic complexes as supported catalysts is a key route in energy production and in industrial synthesis. However, their intrinsic oxygen sensitivity is sometimes an issue. Some of us have recently demonstrated that hydrogenases, the fragile but very efficient biological catalysts of H2 oxidation, can be protected from O2 damage upon integration into a film of a specifically designed redox polymer. Catalytic oxidation of H2 produces electrons which reduce oxygen near the film/solution interface, thus providing a self-activated protection from oxygen [Plumeré et al., Nat Chem. 2014, 6, 822-827]. Here, we rationalize this protection mechanism by examining the time-dependent distribution of species in the hydrogenase/polymer film, using measured or estimated values of all relevant parameters and the numerical and analytical solutions of a realistic reaction-diffusion scheme. Our investigation sets the stage for optimizing the design of hydrogenase-polymer films, and for expanding this strategy to other fragile catalysts. © 2015 American Chemical Society.

A test procedure for alkali-free Cu-Co-based catalysts synthesized by co-precipitation was established allowing the fast assessment and screening of their catalytic properties in the synthesis of higher alcohols by online GC analysis. Due to precisely controlled initial deactivation of the catalysts at 280 °C long-term measurements were avoided and steady-state conditions at 260 °C were reached within a short period of time. Temperatures up to 300 °C were found to favor the formation of methanol, whereas the product distribution was not affected at lower space velocities. Even traces of alkali ions present due to insufficient washing were found to strongly affect the catalytic properties. (Graph Presented). © Springer Science+Business Media 2015

Functionalization of graphene is fundamental to facilitating its processing and offers a wide scope for advanced applications. Here we demonstrate a facile, highly efficient and mild covalent functionalization of graphene using HNO3 vapour. This results in functionalized few-layer graphene (FLG) that is high in both quantity and quality. We fully characterized the structure and defect level of functionalized FLG by X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy and Raman spectroscopy. The results from this analysis show the tunability of the surface oxygen functionalities of FLG achieved through controlling the oxidation temperature without affecting the major intrinsic properties of graphene. This allows for further doping for applications, for example with nitrogen as a metal-free catalyst in the oxygen reduction reaction. © 2015 The Royal Society of Chemistry.

The efficiency of industrial methanol synthesis from syngas results from a complex scenario of surface chemical reactions in the presence of dynamical morphological changes of the catalyst material in response to the chemical and physical properties of the gas phase, which are believed to explain the superior performance of the Cu/ZnO catalyst. Yet, the applied conditions of elevated temperatures and pressures substantially hamper in situ experimental access and, therefore, detailed understanding of the underlying reaction mechanism(s) and active site(s). Here, part of this huge space of possibilities emerging from the structural and chemical configurations of both, adsorbates and continuously altering Cu/ZnO catalyst material, is successfully explored by pure computational means. Using our molecular dynamics approach to computational heterogeneous catalysis, being based on advanced ab initio simulations in conjunction with thermodynamically optimized catalyst models, the resulting mapping of the underlying free energy landscape discloses an overwhelmingly rich network of parallel, competing, and reverse reaction channels. After having analyzed various pathways that directly lead from CO2 to methanol, not only specific Cu/ZnO interface sites but also the near surface region over the catalyst surface were identified as key to some pivotal reaction steps in the global reaction network. Analysis of the mechanistic details and electronic structure along individual steps unveils three distinct mechanisms of surface chemical reactions being all at work, namely Eley-Rideal, Langmuir-Hinshelwood, and Mars-van Krevelen. Importantly, the former and latter mechanisms can only be realized upon including systematically the near surface region and dynamical transformations of catalyst sites, respectively, in the reaction space throughout all simulations.

With the high interest in improving the performance of electrocatalysts for technologically significant reactions, great efforts are directed at the assessment of the activities of various catalytic materials. For this purpose, it is important to compare the catalytic activities measured using different methods and under different conditions. To achieve this, it is of utmost importance to avoid certain methodological and instrumental issues that can severely affect the obtained experimental results. Using well-defined systems, we demonstrate the importance of experimental conditions in the assessment and benchmarking of the activity of catalytic processes for various reactions. Particularly, we demonstrate that the correction of the uncompensated ohmic resistance using impedance spectroscopy measurements requires particular attention and additional procedures which are normally ignored. Additionally, we demonstrate how the uncompensated resistance changes with the potential if a non-conducting gas phase is accumulated in the system, hence influencing the activity measurement. It is further shown that a correct choice for surface-limited reactions for the determination of the real surface area of catalytic electrodes plays a key role in ensuring more meaningful activity assessment. Not as easy as it seems: Benchmarking of the electrocatalytic activity can be unexpectedly very demanding due to experimental issues which are often underestimated. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Iron phthalocyanine-based materials have been used herein as efficient catalysts for the ammonia decomposition reaction. These materials showed high activity, even superior to that showed by the commercial nickel-based catalyst and iron-doped carbon nanotubes, which were used as benchmarks in this study. Catalyst stability under reaction conditions appeared satisfactory, because no deactivation phenomena were observed. The type of the phthalocyanine precursor did not affect the catalytic performance; however, the preparation method had a strong effect. If the resulting material was exposed to the reaction conditions, some structural modification occurred. No clear correlation between phase composition and activity could be established because similar nitrogen content and similar crystalline domains in the sample led to different behaviors. However, the results of extensive characterization suggested that catalytic activities and conversion profiles were most likely dependent on material textural properties and thus on the preparation method used. The accessibility of iron species seems to be limited for catalysts prepared under vacuum. These phenomena are most likely responsible for the activation profile and for the low catalytic activity typical of these materials. In contrast, higher accessibility of iron species, typical of materials prepared under argon, would lead to improved and stable catalytic performance. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A new approach to produce highly porous carbide-derived carbon nanospheres of 20-200 nm diameter based on a novel soft-templating technique is presented. A platinum catalyst is used for the cross-linking of liquid (allylhydrido)polycarbosilane polymer chains with para-divinylbenzene within oil-in-water miniemulsions. Quantitative implementation of the pre-ceramic polymer can be achieved allowing precise control over the resulting materials. After pyrolysis and high-temperature chlorine treatment, the resulting particles offer a spherical shape, very high specific surface area (up to 2347 m2 g-1), and large micro/mesopore volume (up to 1.67 cm3 g-1). The internal pore structure of the nanospheres is controllable by the composition of the oil phase within the miniemulsions. The materials are highly suitable to be used as supercapacitor electrodes with high specific capacitances in aqueous 1 M Na2SO4 solution (110 F g-1) and organic 1 M tetraethylammonium tetrafluoroborate in acetonitrile (130 F g-1). © The Royal Society of Chemistry 2015.

Silica-supported catalysts for the conversion of ethanol to 1,3-butadiene were investigated. The combination of Hf(IV) and Zn(II) resulted in a stable, active, and selective catalyst in which the Zn(II) effectively suppressed the dehydration activity of Hf(IV); the catalyst preparation method plays a crucial role. Using the crystalline Zn-silicate hemimorphite as an alternative Zn(II) source proved to be even more successful in suppressing ethanol dehydration. © 2015 American Chemical Society.

Co3O4 with a spinel structure is a very active oxide catalyst for the oxidation of CO. In such catalysts, octahedrally coordinated Co3+ is considered to be the active site, while tetrahedrally coordinated Co2+ is assumed to be basically inactive. In this study, a highly ordered mesoporous CoO has been prepared by H2 reduction of nanocast Co3O4 at low temperature (250 °C). The as-prepared CoO material, which has a rock-salt structure with a single Co2+ octahedrally coordinated by lattice oxygen in Fm3¯m symmetry, exhibited unexpectedly high activity for CO oxidation. Careful investigation of the catalytic behavior of mesoporous CoO catalyst led to the conclusion that the oxidation of surface Co2+ to Co3+ causes the high activity. Other mesoporous spinels (CuCo2O4, CoCr2O4, and CoFe2O4) with different Co species substituted with non/low-active metal ions were also synthesized to investigate the catalytically active site of cobalt-based catalysts. The results show that not only is the octahedrally coordinated Co3+ highly active but also the octahedrally coordinated Co2+ species in CoFe2O4 with an inverse spinel structure shows some activity. These results suggest that the octahedrally coordinated Co2+ species is easily oxidized and shows high catalytic activity for CO oxidation. © 2015 American Chemical Society.

A catalyst consisting of copper nanoparticles (15-20 nm in size) supported on ordered mesoporous cobalt monoxide was synthesized by the one-step reduction of ethanol from nanocast copper cobalt spinel oxides. The small-angle X-ray scattering patterns showed that the ordered mesostructure was maintained after post-treatment, and the cross-section scanning electron microscopy images showed that the Cu nanoparticles were distributed homogeneously throughout the mesoporous CoO framework. The materials were tested as noble-metal-free catalysts for the oxidation of glycerol under alkaline conditions. The catalytic data showed that the presence of Cu nanoparticles greatly enhanced the catalytic performance. Nothing noble: A catalyst consisting of copper nanoparticles (NPs, 15-20 nm in size) supported on ordered mesoporous cobalt monoxide is synthesized by the one-step reduction with ethanol from nanocast copper cobalt spinel oxides. As a noble-metal-free catalyst for the oxidation of glycerol, the presence of Cu NPs greatly enhances the catalytic performance. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An efficient two-step gas-phase method was developed for the synthesis of Co3O4-MnO2-CNT hybrids used as electrocatalysts in the oxygen evolution reaction (OER). Spinel Co-Mn oxide was used for the catalytic growth of multiwalled carbon nanotubes (CNTs) and the amount of metal species remaining in the CNTs was adjusted by varying the growth time. Gas-phase treatment in HNO3 vapor at 200 °C was performed to 1)open the CNTs, 2)oxidize encapsulated Co nanoparticles to Co3O4 as well as MnO nanoparticles to MnO2, and 3)to create oxygen functional groups on carbon. The hybrid demonstrated excellent OER activity and stability up to 37.5h under alkaline conditions, with longer exposure to HNO3 vapor up to 72h beneficial for improved electrocatalytic properties. The excellent OER performance can be assigned to the high oxidation states of the oxide nanoparticles, the strong electrical coupling between these oxides and the CNTs as well as favorable surface properties rendering the hybrids a promising alternative to noble metal based OER catalysts. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cavity microelectrodes were used as a binder-free platform to evaluate oxygen evolution reaction (OER) electrocatalysts with respect to gas bubble formation and departure. Electrochemical noise measurements were performed by using RuO2 as a benchmark catalyst and the perovskite La0.58Sr0.4Fe0.8Co0.2O3 as a non-noble metal OER catalyst with lower intrinsic conductivity. Changes in the current during the OER originate from variations in electrolyte resistance during the formation of the gas phase and partial coverage of the active area. Fluctuations observed in current and conductance transients were used to establish the contribution from the ohmic overpotential and to determine the characteristic frequency of oxygen evolution. The proposed quantitative determination of gas bubble growth and departure opens up the route for a rational interface design by considering gas bubble growth and departure as a main contributing factor to the overall electrocatalytic activity at high current densities. © 2015 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrolyte components, which are typically not considered to be directly involved in catalytic processes at solid-liquid electrified interfaces, often demonstrate a significant or even drastic influence on the activity, stability and selectivity of electrocatalysts. While there has been certain progress in the understanding of these electrolyte effects, lack of experimental data for various important systems frequently complicates the rational design of new active materials. Modern proton-exchange membrane (PEM) electrolyzers utilize Pt- and Ir-based electrocatalysts, which are among the very few materials that are both active and stable under the extreme conditions of water splitting. We use model Pt(111) and Ir-oxide films grown on Ir(111) electrodes and explore the effect of alkali metal cations and sulfate-anions on the hydrogen evolution and the oxygen evolution reactions in acidic media. We demonstrate that sulfate anions decrease the activity of Ir-oxide towards the oxygen evolution reaction while Rb+ drastically promotes hydrogen evolution reaction at the Pt(111) electrodes as compared to the reference HClO4 electrolytes. Issues related to the activity benchmarking for these catalysts are discussed. This journal is © the Owner Societies.

The predominantly insulating nature of zeolites, as many classes of porous catalysts, can severely impair heat transfer and hence their performance in industrial processes. Strategies developed to engineer the thermophysical properties of technical zeolites for fixed-bed applications comprise the use of conductive secondary phases as structured catalyst supports or as inert diluents. However, the impact of integrating conductive additives into composite zeolite bodies (pellets, extrudates, or granules) has not been widely explored. Here, using a transient hot-plate technique to decouple the distinct contributions of porosity, sample hydration, and temperature, we quantify the impact of metallic (copper), ceramic (silicon carbide, aluminum nitride, boron nitride), and carbonaceous (graphite, carbon nanotubes) phases on the thermal conductivity of shaped zeolites at the body and packed-bed scales. The decisive role of particle morphology, dominating over the intrinsic conductivity of an additive, is corroborated through the three-dimensional reconstruction of data acquired by focused ion beam-scanning electron microscopy and X-ray microtomography coupled with in-situ thermographic studies. In particular, the order-of-magnitude improvement evidenced on application of graphite sheets stems from the extended paths of low thermal resistance created in the millimeter-sized catalyst ensemble. Through the identification of structure-property relations, our approach provides new insights into the rational design of composite porous materials with enhanced heat-transfer properties. © 2015 Elsevier Inc.

This work introduces a practical and scalable post-synthesis treatment for carbon-supported catalysts designed to achieve complete activation and, if necessary, simultaneously surface dealloying. The core concept behind the method is to control the potential without utilizing any electrochemical equipment, but rather by applying an appropriate gas mixture to a catalyst suspension. © 2015 The Royal Society of Chemistry.

A good heterogeneous catalyst for a given chemical reaction very often has only one specific type of surface site that is catalytically active. Widespread methodologies such as Sabatier-type activity plots determine optimal adsorption energies to maximize catalytic activity, but these are difficult to use as guidelines to devise new catalysts. We introduce "coordination-activity plots" that predict the geometric structure of optimal active sites. The method is illustrated on the oxygen reduction reaction catalyzed by platinum. Sites with the same number of first-nearest neighbors as (111) terraces but with an increased number of second-nearest neighbors are predicted to have superior catalytic activity. We used this rationale to create highly active sites on platinum (111), without alloying and using three different affordable experimental methods.

Cu-Co-based catalysts were synthesized by co-precipitation using Cu, Co, Zn and Al nitrates and applied in higher alcohol synthesis (HAS) at 280 °C, 60 bar and a ratio of H2/CO = 1. The catalyst exhibiting a Cu/Co ratio of 2.5 was found to provide the best trade-off between product distribution and degree of CO conversion. After activation and 40 h time on stream reaching steady-state conditions the bulk and surface properties of the catalyst were thoroughly investigated without exposing it to air during the transfer and the measurements. The conditions during activation and HAS led to a significant enrichment of Zn in the surface composition of the catalysts. The XRD pattern of the catalyst after reaction compared with the reduced catalyst revealed further sintering of the metallic Cu nanoparticles and the growth of crystalline ZnO nanoparticles, but there were no indications for the presence of bulk metallic Co or for bulk alloying. With increasing time on stream the product distribution shifted favorably towards higher alcohols presumably due to an increased intimate interface contact between the large metallic Cu0 particles detected by XRD and the X-ray amorphous metallic Co surface species probed by XPS. © 2015 Elsevier B.V.

Cu-Co-based model catalysts were prepared by a sophisticated alkali-free synthesis method and tested in the conversion of synthesis gas to higher alcohols. MoO3-coated alumina was used as the support, providing both high specific surface area and strongly interacting sites for the deposition of the active metals. A bulk Cu/Co ratio of ∼2 was found to be most suitable in terms of activity and product distribution. Surface enrichment of Mo for all samples was observed by XPS, which significantly influenced the performance of the catalysts. Mo was found to be both a structural and a chemical promoter. Strong metal-support interactions were further achieved by modification of alumina with magnesia. With 12 wt% Mg incorporated, the catalysts showed 40% total oxygenate selectivity including 11% selectivity to ethanol. © The Royal Society of Chemistry 2015.

The power output of a fuel cell is limited by among others, the intrinsic activity of the active matrix and the mass transport of the products and reactants. Of equally crucial importance is the long-term durability of the cell components including the electrocatalysts. Herein, carbon cloth (CC) was functionalized with nitrogen-containing groups by treatment with NH3 at 400 °C or by pyrolysis of a composite of polypyrrole on CC at 800 °C. The resulting N-doped CC (NCC) was employed as an air-breathing cathode in a custom-made air/H2 alkaline fuel cell, serving as the current collector as well as catalytic matrix with enhanced oxygen transport. The cell exhibited high operational durability with only 2% loss in activity after 25 days and delivered a maximum power density of 120 mW m-2 at a voltage of 0.35 V. The concept of a self-supported highly stable metal-free catalyst and the breathing H2/air cell design provide platforms for the design and investigation of catalysts. Moreover, a higher cell voltage can be realized if the cell is operated under pressurized conditions or by replacing air with O2. © 2015 Published by Elsevier Ltd.

The recent surge in investigating electrocatalysts for the H2 evolution reaction is based on finding a cheap alternative to Pt. However platinum's excellent catalytic activity means very little catalyst needs to be used. The present study combines model experiments with numerical modeling to determine exactly how little catalyst is needed. Specifically we investigate ultra-low Pt loadings for use in photoelectrochemical H2 evolution using TiO2-Ti-pn+Si photocathodes. At a current density of 10 mA cm-2, we photocathodically evolve H2 at +465, +450, +350 and +270 mV vs., RHE at Pt loadings of 1000, 200, 50, and 10 ng cm-2 corresponding to HER overpotentials of η1000ng = 32 mV, η200ng = 46 mV, η50ng = 142 mV, and η10ng = 231 mV. To put this in perspective, if 30% of the world's current annual Pt production was used for H2 evolution catalysis, using a loading of 100 ng cm-2 and a current of 10 mA cm-2 would produce 1 TWaverage of H2. The photoelectrochemical data matched the modeling calculations implying that we were near the fundamental maximum in performance for our system. Furthermore modeling indicated that the overpotentials were dominated by mass transfer effects, rather than catalysis unless catalyst loadings were less than 1000 ng cm-2. © The Royal Society of Chemistry.

When Haldor Topsøe founded his company in 1940, the application of solid catalysts in industrial chemical processes was still in its early phase. At that time, catalyst development and optimization strongly relied on phenomenological approaches and experimental know-how, whereas little knowledge existed on the nature of the catalytically active species and how to tune their structure and concentration. For more than 70 years, Topsøe has advocated the need of "bringing more scientific understanding to the field of catalysis," becoming a prominent figure in the transition of catalyst preparation - a word with an alchemical connotation - to catalyst synthesis, based on scientific principles. Numerous fundamental studies of his team and collaborators on simplified model catalysts have added substantially to the current understanding of a significant number of industrially relevant systems in particular, and the principles of action of solid catalysts in general. This article reviews some key advancements that the Topsøe team has contributed to the field of catalyst development, rooted in fundamental studies with either 2D or 3D model materials. Examples are provided of how the acquired scientific knowledge was successfully translated into innovations in the manufacture of technical catalysts. Next to the work of the Topsøe group, a broader and updated perspective of the use of model systems to investigate fundamental aspects of catalyst development is presented. A number of selected case studies are reviewed, which we find illustrative of recent findings with implications for the design and synthesis of solid catalysts. © 2015 Elsevier Inc. All rights reserved.

TiO2-supported gold species were prepared via the deposition-precipitation route, with conservation of the initial speciation by freeze-drying. The structural and electronic properties of the Au species were investigated by X-ray absorption spectroscopy, electron microscopy, and IR spectroscopy of adsorbed CO in four states. Exclusively AuIII was deposited on the TiO2 surface in patches ranging from isolated Au ions to three-dimensional clusters. This paper illustrates in detail the unique contributions of all characterization techniques to this structural model. © 2014 Wiley-VCH Verlag GmbH & Co. KGaA.

Different surface sites of solid catalysts are usually quantified by dedicated chemisorption techniques from the adsorption capacity of probe molecules, assuming they specifically react with unique sites. In case of methanol synthesis catalysts, the Cu surface area is one of the crucial parameters in catalyst design and was for over 25 years commonly determined using diluted N2O. To disentangle the influence of the catalyst components, different model catalysts were prepared and characterized using N2O, temperature programmed desorption of H2, and kinetic experiments. The presence of ZnO dramatically influences the N2O measurements. This effect can be explained by the presence of oxygen defect sites that are generated at the Cu-ZnO interface and can be used to easily quantify the intensity of Cu-Zn interaction. N2O in fact probes the Cu surface plus the oxygen vacancies, whereas the exposed Cu surface area can be accurately determined by H2. A combination of N2O reactive frontal chromatography and H2 temperature-programmed desorption is used to analyze the interplay of copper and zinc oxide in methanol synthesis catalysts. This method provides an easy in situ approach to quantify the direct copper-zinc interaction (SMSI effect) and offers an important possibility to rational catalyst design also for other supported metal catalysts. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Metal-free nitrogen modified carbon catalysts (NC) are very closely related to MNC catalysts which contain a transition metal(s) (M), usually Fe or Co as an essential constituent. We investigated the influence of metal inclusions on the activity of nitrogen-doped carbon black in the electrocatalysis of the oxygen reduction reaction (ORR). A reference metal-free NC catalyst was prepared by pyrolysis of a polypyrrole/Vulcan XC72 composite at 800 °C for 2 h under helium. Controlled amounts of Co, Fe, Mn and Ni in low concentrations were then introduced into NC by impregnating it with the corresponding meso-tetra(4-pyridyl) porphyrin metal complex followed by further pyrolysis at 650 °C for 2 h under helium. The resulting catalysts were investigated for ORR using rotating disk electrode and rotating-ring disk electrode voltammetry in 0.1 M KOH. Additionally, the rate of decomposition of hydrogen peroxide by the different catalysts was determined in order to probe the influence of the metal inclusions on the mechanism and selectivity of the ORR. The results show that Fe, Co and Mn inclusions cause a substantial decrease of the overpotential of the reaction and enhance the catalytic current, whereas the presence of Ni has a poisoning effect on ORR. In the presence of Fe, the catalysts apparently reduce oxygen selectively to OH- in a direct four electron transfer process as opposed to the two-step, two electron pathway involving hydrogen peroxide as an intermediate for the case of the NC catalyst. © 2013 Elsevier Ltd.

Platinum and Pt alloy nanoparticles supported on carbon are the state of the art electrocatalysts in proton exchange membrane fuel cells. To develop a better understanding on how material design can influence the degradation processes on the nanoscale, three specific Pt/C catalysts with different structural characteristics were investigated in depth: a conventional Pt/Vulcan catalyst with a particle size of 3-4 nm and two Pt@HGS catalysts with different particle size, 1-2 nm and 3-4 nm. Specifically, Pt@HGS corresponds to platinum nanoparticles incorporated and confined within the pore structure of the nanostructured carbon support, i.e., hollow graphitic spheres (HGS). All three materials are characterized by the same platinum loading, so that the differences in their performance can be correlated to the structural characteristics of each material. The comparison of the activity and stability behavior of the three catalysts, as obtained from thin film rotating disk electrode measurements and identical location electron microscopy, is also extended to commercial materials and used as a basis for a discussion of general fuel cell catalyst design principles. Namely, the effects of particle size, inter-particle distance, certain support characteristics and thermal treatment on the catalyst performance and in particular the catalyst stability are evaluated. Based on our results, a set of design criteria for more stable and active Pt/C and Pt-alloy/C materials is suggested.& copy 2014 Meier et al.

Nanoporous Cu-O system catalysts with different oxidation states of Cu have been fabricated through a combination of dealloying as-milled Al66.7Cu33.3 alloy powders and subsequent thermal annealing. X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) have been used to characterize the microstructure and surface chemical states of Cu-O catalysts. The peculiar nanoporous structure can be retained in Cu-O catalysts after thermal treatment. Catalytic experiments reveal that all the Cu-O samples exhibit complete CO conversion below 170 °C. The optimal catalytic performance could be achieved through the combination of annealing in air with hydrogen treatment for the Cu-O catalyst, which shows a near complete conversion temperature (T90%) of 132 °C and an activation energy of 91.3 KJ mol-1. In addition, the present strategy (ball milling, dealloying and subsequent thermal treatment) could be scaled up to fabricate high-performance Cu-O catalysts towards CO oxidation. This journal is © The Royal Society of Chemistry 2014.

Multidimensional shearforce-based constant-distance mode scanning electrochemical microscopy (4D SF/CD-SECM) was utilized for the investigation of the activity distribution of oxygen reduction catalysts. Carbon-supported Pt model catalyst powders have been immobilized in recessed microelectrodes and compared to a spot preparation technique. Microcavities serve as platform for the binder-free catalyst sample preparation exhibiting beneficial properties for constant-distance mode SECM imaging concerning modified surface area and catalyst loading. The integration of the redox competition mode of SECM into the detection scheme of the 4D SF/CD mode is demonstrated for specifically adapting high-resolution SECM experiments to powder-based catalyst preparations. © 2014 Nebel et al.

A series of Cu-exchanged Al-rich Beta zeolites from organotemplate-free synthesis was prepared and investigated for selective catalytic reduction (SCR) of NOx with NH3 in exhaust gas streams. In comparison to conventional Cu-Beta zeolite with Si/Al ratio of 19, Cu-Beta zeolite with Si/Al ratio of 4 is a superior low-temperature NH3-SCR catalyst. Very high NO conversion (>95%) can be achieved at temperatures as low as 150 to ∼400 °C. XRD, UV-Vis-NIR and NH3-TPD measurements show that more isolated Cu2+ ions are present at the exchange sites of Al-rich Beta zeolite. The combination of CO-FTIR and H2-TPR analysis demonstrates that Cu2+ ions could be reduced more readily on the Al-rich Beta than on the conventional Beta probably due to the proximity of the isolated Cu2+ ions. These can be correlated to the enhancement of NO conversion at lower temperatures over Cu-exchanged Al-rich Beta zeolite. © 2014 Elsevier Inc.

CO2 hydrogenation to short-chain hydrocarbons was investigated over iron catalysts supported on oxygen- and nitrogen-functionalized multi-walled carbon nanotubes (CNTs) and on silica, which were synthesized by the dry impregnation method using ammonium ferric citrate as precursor. The reduction of the calcined catalysts was examined in detail using temperature-programmed reduction in H2 and in situ X-ray absorption near-edge structure (XANES) analysis. The XANES results revealed that the mixture of hematite and magnetite was gradually transformed into wustite and metallic iron during heating in H2. Iron oxide nanoparticles supported on nitrogen-functionalized CNTs were easier to reduce compared to those on oxygen-functionalized CNTs indicating a promoting effect of the nitrogen functional groups. The interaction between iron oxide and silica was found to be much stronger inhibiting the reduction to metallic iron. As a result, the catalytic activity of iron nanoparticles supported on CNTs in CO2 hydrogenation at 360 °C, 25 bar and a H2:CO 2 ratio of 3 was almost twofold higher compared with iron supported on silica. CO2 was converted into C1-C5 hydrocarbons with CO and methane as major products over all catalysts. The Fe/NCNT catalyst achieved the highest olefin selectivity of 11% in the hydrocarbons range of C2-C5. In contrast, mostly paraffins were formed over the Fe/SiO2 catalyst. © 2014 Elsevier B.V.

Nanocrystalline rutile TiO2 powders were modified with small amounts of CuOx and FeOx clusters by impregnation and drying. The modified rutile samples exhibited drastically enhanced photocatalytic degradation of 4-chlorophenol under UV + vis (λ > 320 nm) irradiation. The reaction rates were increased by the factor of 7 and 4 for the optimized TiO2(R)-CuOx and TiO2(R)-FeO x samples containing 0.12 wt.% Cu and 0.13 wt.% Fe, respectively. The visible light (λ > 455 nm) activity in 4-CP degradation was negligible. Photopotential transient measurements have confirmed that amorphous CuOx and FeOx clusters deposited at the surface of rutile TiO2 act as efficient co-catalysts for oxygen reduction by photogenerated electrons, which leads to improved charge separation and diminished recombination. This study shows that simple modification of TiO 2 photocatalysts with redox co-catalysts based on metal oxides is a promising strategy for enhancing the photocatalytic activity in degradation of aqueous pollutants. © 2013 Elsevier B.V.

The catalytic performance of a Ni/MgAlOx catalyst was investigated in the high temperature CO2 reforming of CH4. The catalyst was developed using a Ni, Mg, Al hydrotalcite-like precursor obtained by co-precipitation. Despite the high Ni loading of 55 wt%, the synthesized Ni/MgAlOx catalyst possessed a thermally stable microstructure up to 900 °C with Ni nanoparticles of 9 nm. This stability is attributed to the embedding nature of the oxide matrix, and allows increasing the reaction temperature without losing active Ni surface area. To evaluate the effect of the reaction temperature on the reforming performance and the coking behavior, two different reaction temperatures (800 and 900 °C) were investigated. At both temperatures the prepared catalyst showed high rates of CH4 consumption. The higher temperature promotes the stability of the catalyst performance due to mitigation of the carbon formation. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The efficiency of polymer electrolyte membrane fuel cells is strongly depending on the electrocatalyst performance, that is, its activity and stability. We have designed a catalyst material that combines both, the high activity for the decisive cathodic oxygen reduction reaction associated with nanoscale Pt alloys, and the excellent durability of an advanced nano-structured support. Owing to the high specific activity and large active surface area, the catalyst shows extraordinary mass activity values of 1.0 AmgPt -1. Moreover, the material retains its initial active surface area and intrinsic activity during an extended accelerated aging test within the typical operation range. This excellent performance is achieved by confined space alloying of the nanoparticles in a controlled manner in the pores of the support. © 2014 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Insufficient electrochemical stability is a major challenge for carbon materials in oxygen reduction reaction (ORR) due to carbon corrosion and insufficient metal-support interactions. In this work, titania is explored as an alternative support for Pt catalysts. Oxygen deficient titania samples including TiO2-x and TiO2-xNy were obtained by thermal treatment of anatase TiO2 under flowing H2 and NH3, respectively. Pt nanoparticles were deposited on the titania by a modified ethylene glycol method. The samples were characterized by N2-physisorption, X-ray diffraction and X-ray photoelectron spectroscopy. The ORR activity and long-term stability of supported Pt catalysts were evaluated using linear sweep voltammetry and chronoamperometry in 0.1 mol/L HClO4. Pt/TiO2-x and Pt/TiO2-xNy showed higher ORR activities than Pt/TiO2 as indicated by higher onset potentials. Oxygen deficiency in TiO2-x and TiO2-xNy contributed to the high ORR activity due to enhanced charge transfer, as disclosed by electrochemical impedance spectroscopy studies. Electrochemical stability studies revealed that Pt/TiO2-x exhibited a higher stability with a lower current decay rate than commercial Pt/C, which can be attributed to the stable oxide support and strong interaction between Pt nanoparticles and the oxygen-deficient TiO2-x support. © 2014 Dalian Institute of Chemical Physics, the Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Au/TiO2 catalysts prepared by a deposition-precipitation process and used for CO oxidation without previous calcination exhibited high, largely temperature-independent conversions at low temperatures, with apparent activation energies of about zero. Thermal treatments, such as He at 623 K, changed the conversion-temperature characteristics to the well-known S-shape, with activation energies slightly below 30 kJ mol-1. Sample characterization by XAFS and electron microscopy and a low-temperature IR study of CO adsorption and oxidation showed that CO can be oxidized by gas-phase O2 at 90 K already over the freeze-dried catalyst in the initial state that contained Au exclusively in the +3 oxidation state. CO conversion after activation in the feed at 303 K is due to AuIII-containing sites at low temperatures, while Au0 dominates conversion at higher temperatures. After thermal treatments, CO conversion in the whole investigated temperature range results from sites containing exclusively Au0. Ionic or metallic: Au3+ ions on TiO2 (see HAADF-STEM image of a freshly prepared sample) can catalyze the oxidation of CO at low temperatures. The reaction rates at Au3+-containing centers are similar to those found at metallic gold clusters. However, the apparent activation energies are very low, which is probably due to the opposing influence of the true activation energy and the adsorption enthalpy of CO on Au3+ centers. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The oxygen evolution reaction (OER) is an enabling process for technologies in the area of energy conversion and storage, but its slow kinetics limits its efficiency. We performed an electrochemical evaluation of 14 different perovskites of variable composition and stoichiometry as OER electrocatalysts in alkaline media. We particularly focused on improved methods for a reliable comparison of catalyst activity. From initial electrochemical results we selected the most active samples for further optimization of electrode preparation and testing. An inverted cell configuration facilitated gas bubble detachment and thus minimized blockage of the active surface area. We describe parameters, such as the presence of specific cations, stoichiometry, and conductivity, that are important for obtaining electroactive perovskites for OER. Conductive additives enhanced the current and decreased the apparent overpotential of OER for one of the most active samples (La0.58Sr0.4Fe0.8Co0.2O3). Low-cost electrocatalysts: A family of perovskites has been studied as new electrocatalysts for the oxygen evolution reaction (OER) in alkaline media. Electrochemical characterization demonstrates the promise of this type of materials for the OER, and the use of conductive additives proves useful for obtaining higher current outputs. © 2014 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Methanol synthesis is one of the landmarks of heterogeneous catalysis due to the great industrial significance of methanol as a clean liquid fuel and as a raw material for industry. Understanding in atomistic detail the properties of the underlying metal/oxide catalyst materials as a function of temperature and composition of the reactive gas phase is of utmost importance in order to eventually improve the production process. By performing extensive density functional theory based slab calculations in combination with a thermodynamic formalism we establish an atomistic understanding of gas phase-induced changes of surface morphology, redox properties and reactivity of ZnO supported Cu nanocatalysts. Extending our recent insights [Phys. Rev. Lett., 2013, 110, 086108], we explore surface stabilization mechanisms and site-dependent redox states of both catalyst components as well as the pronounced electronic charge transfer processes across the metal-support interface. Moreover, ab initio molecular dynamics simulations unveil the vital role played by dynamical shape fluctuations of the deposited Cu-8 cluster. The pronounced structural flexibility of the metal nanoparticle is found to enhance CO2 activation over Cu-8 at the elevated temperature conditions of the industrial methanol synthesis process, in addition to activation of CO2 via electronic charge transfer from the ZnO support.

Interlayer expanded zeolites are derived from layered zeolite precursors by inserting a tetrahedrally coordinated atom (T-atom) in between the precursor layers. To achieve this expansion, a Si source like dichlorodimethylsilane or diethoxydimethylsilane is typically used. In the interlayer expansion of the layered zeolite precursor RUB-36, an Fe salt instead of a silylating agent was used to fill up the linking sites in between the layers. The obtained material showed a shift of the first XRD reflection similar to that of RUB-36 interlayer expanded with dichlorodimethylsilane, indicating an increase in interlayer distance. Diffuse reflectance UV-vis spectra and EPR characterization proved the incorporation of isolated Fe sites. Using FTIR spectroscopy with pyridine and acetonitrile as probe molecules, it was found that the incorporation of Fe results in an increase in Lewis acidity. The material was successfully used as a catalyst in the acylation of anisole with acetic anhydride and in the alkylation of toluene with benzyl chloride. The Fe incorporation proved to be remarkably stable. In spite of the HCl production during the alkylation reaction, no leaching was observed and the catalyst could be reused after regeneration. This journal is © the Partner Organisations 2014.

A joint experimental and computational study on the glucose-fructose conversion in water is reported. The reactivity of different metal catalysts (CrCl3, AlCl3, CuCl2, FeCl3, and MgCl2) was analyzed. Experimentally, CrCl3 and AlCl3 achieved the best glucose conversion rates, CuCl2 and FeCl3 were only mediocre catalysts, and MgCl2 was inactive. To explain these differences in reactivity, DFT calculations were performed for various metal complexes. The computed mechanism consists of two proton transfers and a hydrogen-atom transfer; the latter was the rate-determining step for all catalysts. The computational results were consistent with the experimental findings and rationalized the observed differences in the behavior of the metal catalysts. To be an efficient catalyst, a metal complex should satisfy the following criteria: moderate Brønsted and Lewis acidity (pKa=4-6), coordination with either water or weaker σ donors, energetically low-lying unoccupied orbitals, compact transition-state structures, and the ability for complexation of glucose. Thus, the reactivity of the metal catalysts in water is governed by many factors, not just the Lewis acidity. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The synthesis of yolk-shell catalysts, consisting of platinum or gold-platinum cores and graphitic carbon shells, and their electrocatalytic stabilities are described. Different encapsulation pathways for the metal nanoparticles are explored and optimized. Electrochemical studies of the optimized AuPt, @C catalyst revealed a high stability of the encapsulated metal particles. However, in order to reach full activity, several thousand potential cycles are required. After the electrochemical surface area is fully developed, the catalysts show exceptionally high stability, with almost no degradation over approximately 30 000 potential cycles between 0.4 and 1.4 VRHE. Encapsulation of noble metals in graphitic hollow shells by hard templating is explored as a means for stabilizing fuel cell catalysts. Small platinum particles can be encapsulated, but the achievable loading is too small. Encapsulation of Au-Pt yolk-shell particles allows higher loading, and with such cores, stable catalysts could be produced. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The structure and chemical state of size-selected Pt nanoparticles (NPs) supported on γ-Al2O3 were studied during the oxidation of NO using X-ray absorption near-edge spectroscopy and extended X-ray absorption fine-structure spectroscopy measurements under operando conditions. The data revealed the formation of PtOx species in the course of the reaction that remained present at the maximum temperature studied, 350 °C. The PtOx species were found in all samples, but those with the smallest NPs showed the highest degree of oxidation. Moreover, NO-induced nanoparticle redispersion was observed at temperatures below 150 °C for all catalysts studied. Catalytic tests showed activity toward the oxidation of NO for all samples. Nevertheless, the catalyst with the smallest NPs was found to be the least active, which is explained by a more extensive formation of PtOx species in this catalyst and their detrimental contribution to the oxidation of NO. © 2014 American Chemical Society.

A multi-functional flow set-up was developed for the rate- and temperature-controlled reduction of copper catalysts, their application in high-pressure methanol synthesis and the determination of the copper surface area by N2O frontal chromatography. The influence of constant-rate reduction on the catalytic properties of a ternary Cu/ZnO/Al2O3 catalyst was investigated. The temperature during the constant-rate reduction was found to decrease, indicating autocatalytic kinetics, but no significant catalytic effect of the milder reduction conditions was observed compared with a slow linear heating ramp. © 2014 Wiley-VCH Verlag GmbH & Co. KGaA.

A comprehensive microkinetic model, including catalyst descriptors, that accounts for thermal, homogeneous and catalytic, heterogeneous reaction steps in the oxidative coupling of methane has been used in the assessment of kinetic data acquired on different catalysts. The applicability of the model was extended from alkali magnesia catalysts represented by Li/MgO and Sn-Li/MgO, to a new class of materials, namely alkaline earth-promoted lanthana catalysts, represented by Sr/La2O3. To simulate adequately the large experimental dataset, acquired with the latter catalyst, the surface reaction network of the microkinetic model was expanded. The resulting model succeeded in adequately simulating the C2, that is, ethane and ethene, production, both individually and as a lump during regression. It was found that the activity of Sr/La2O3, in terms of methane conversion, is 33 and five times higher than that of Li/MgO and Sn-Li/MgO, respectively. This is attributed mainly to the higher stability of adsorbed hydroxyl, the higher stability of adsorbed oxygen, and the higher active density of Sr/La2O3. The selectivity toward C2 products was found to depend on the methyl radical sticking coefficient and the stability of the adsorbed oxygen and was the highest on the Sn-promoted LiMgO catalyst, that is, 70% at about 5% methane conversion at 1023K, 190kPa, and inlet molar CH4/O2 ratio of 4. © 2014 Elsevier B.V.

This paper presents a thermogravimetric analysis of catalytic methane decomposition using ordered mesoporous carbon nanorods (CMK-3) and ordered mesoporous carbidederived carbon (DUT-19) as catalysts. X-ray diffraction and N2 physisorption analyses were performed for both fresh catalysts. Threshold temperatures for methane decomposition with DUT-19 and CMK-3 were estimated by three different methods found in literature. Carbon formation rate and carbon weight gain as a function of time at various temperatures and methane partial pressures were studied, and the kinetics of CMK-3 and DUT-19 as catalysts for methane decomposition were investigated. Arrhenius energy values of 187 kJ/mol for CMK-3 and 196 kJ/mol for DUT-19 with a reaction order of 0.5 were obtained for both catalysts. Results show that carbon deposition on the catalyst during the reaction lead to catalyst deactivation with significant surface modification. Scanning electron microscope studies of fresh and deactivated catalyst samples show the blocking of catalyst pores and the formation of agglomerates on the outer surface of the catalyst during the course of reaction. DUT-19 catalytically outperforms CMK-3 because of a lower threshold temperature, higher surface area, and higher pore volume. These results show that ordered mesoporous carbons are promising catalysts for methane decomposition. © 2013 Elsevier Ltd. All rights reserved.

Many energy conversion materials show increased performance, if the materials are used in nanostructured form. However, this could be detrimental for stability of the materials, since during cycling the nanostructuring tends to be lost because of particle growth. This problem may be solved by encapsulation of the active material in different types of matrices or coatings, which beyond the stabilization may also provide additional functionality, such as conductivity or mechanical reinforcement. This Perspective covers the general features of encapsulation strategies, and desribes selected examples for different types of energy conversion materials. At the end, promising development lines will be discussed, together with the need for a more systematic study of the effects of encapsulation. © 2013 American Chemical Society.

Reversible interconversion of water into H2 and O2, and the recombination of H2 and O2 to H2O thereby harnessing the energy of the reaction provides a completely green cycle for sustainable energy conversion and storage. The realization of this goal is however hampered by the lack of efficient catalysts for water splitting and oxygen reduction. We report exceptionally active bifunctional catalysts for oxygen electrodes comprising Mn3O4 and Co 3O4 nanoparticles embedded in nitrogen-doped carbon, obtained by selective pyrolysis and subsequent mild calcination of manganese and cobalt N4 macrocyclic complexes. Intimate interaction was observed between the metals and nitrogen suggesting residual M-Nx coordination in the catalysts. The catalysts afford remarkably lower reversible overpotentials in KOH (0.1M) than those for RuO2, IrO2, Pt, NiO, Mn3O4, and Co3O4, thus placing them among the best non-precious-metal catalysts for reversible oxygen electrodes reported to date. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

CNT growth experiments on a cobalt-based catalyst were conducted in a tubular fixed bed reactor at different temperatures and ethene concentrations. The measured kinetic data were analyzed with an isothermal, dynamic reactor model taking into account pore and film diffusion as well as the size of CNT agglomerates as a function of time. Based on previously published results it was found that the CNT agglomerates are enlarged by an average factor of 6.5 compared to the original diameter of the catalyst particle. Under these conditions, the development of the agglomerate diameter with time can be described with a single parameter which is independent of the reaction conditions. The rate of the CNT growth was determined to be first order in the ethene concentration with an activation energy of 107. kJ/mol. The catalyst deactivation by cumulative encapsulation of active sites was found to be second order with respect to the consumed amount of ethene with a rate constant independent of the temperature. Nevertheless, deactivation takes place faster at higher temperatures and/or ethene concentrations, since the deactivation process is directly coupled to the rate of CNT synthesis. © 2014 Elsevier B.V.

The photocatalytic reduction of CO2 by water vapor to produce light hydrocarbons was studied over a series of catalysts consisting of variable loading of Ti incorporated in TUD-1 mesoporous silica, either modified by ZnO nanoparticles or isolated Cr-sites. Unexpectedly, the performance of ZnO-Ti-TUD-1 and Cr-Ti-TUD-1 was inferior to the parent Ti-TUD-1. An explanation can be found in experiments on the photocatalytic degradation of a mixture of hydrocarbons (i.e., CH4, C2H4, C 2H6, C3H6, and C3H 8) under the same illumination conditions. Ti-TUD-1 exhibits the poorest activity in hydrocarbon degradation, while ZnO-Ti-TUD-1 and Cr-Ti-TUD-1 showed very significant degradation rates. This study clearly demonstrates the importance of evaluating hydrocarbon conversion over photocatalysts active in converting CO2 to hydrocarbons (in batch reactors). © 2013 American Chemical Society.

The notorious instability of non-precious-metal catalysts for oxygen reduction and evolution is by far the single unresolved impediment for their practical applications. We have designed highly stable and active bifunctional catalysts for reversible oxygen electrodes by oxidative thermal scission, where we concurrently rupture nitrogen-doped carbon nanotubes and oxidize Co and Mn nanoparticles buried inside them to form spinel Mn-Co oxide nanoparticles partially embedded in the nanotubes. Impressively high dual activity for oxygen reduction and evolution is achieved using these catalysts, surpassing those of Pt/C, RuO2, and IrO2 and thus raising the prospect of functional low-cost, non-precious-metal bifunctional catalysts in metal-air batteries and reversible fuel cells, among others, for a sustainable and green energy future. © 2014 American Chemical Society.

We describe a solid polyphenylene support that serves as an excellent platform for metal-catalyzed reactions that are normally carried out under homogeneous conditions. The catalyst is synthesized by palladium-catalyzed Suzuki coupling which directly results in formation of palladium nanoparticles confined to a porous polyphenylene network. The composite solid is in turn highly active for further Suzuki coupling reactions, including non-activated substrates that are challenging even for molecular catalysts. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Surface-modified TiO2 photocatalysts were synthesized by a photosynthetic route involving visible-light-induced (l> 455 nm) activation of benzene and toluene at the surface of TiO2 leading to the formation of carbonaceous polymeric deposits. IR spectroscopic and photoelectrochemical experiments showed that the mechanism of the photosynthetic reactions involves intra-bandgap surface states at TiO2 related to surface OH groups interacting with adsorbed aromatic molecules. The photosynthesized surface-modified TiO2 materials exhibited enhanced activity, relative to pristine TiO2, in photocatalytic degradation (and complete mineralization) of 4-chlorophenol. The improvement was pronounced particularly under visible-light (l>455 nm) irradiation with the relative initial photodegradation rate enhanced by a factor of four. The surface-modified photocatalysts exhibited good stability under the operating conditions, and the optimum carbon content was approximately 0.5 wt%. Mechanistic studies showed that the enhanced visible-light photodegradation of 4-chlorophenol is due to modified surface-adsorption properties that facilitate formation of a surface complex between titania and 4-chlorophenol, rather than due to any sensitizing effect of the carbonaceous deposits. The study highlights the importance of considering the interaction between pollutant molecules and the photocatalyst surface in heterogeneous photocatalysis, and possibly opens up a route for photosynthesis of further surface- modified photocatalysts with tuned surface properties. © 2014 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Interlayer expansion of layered zeolite precursors is achieved via the insertion of an additional T-atom in between the layers, typically by means of a silylating agent as source of the T-atom. (3-Mercaptopropyl) methyldimethoxysilane was used as Si-source in the interlayer expansion of the layered zeolite precursors RUB-36 and RUB-39. The structure expansion was confirmed with PXRD. The incorporation of the silylating agent was followed with 29Si MAS NMR, 13C CP MAS NMR and thermogravimetric analysis. The incorporated thiol groups were oxidized with H2O 2 to obtain sulfonic acid groups in between the layers. 13C CP MAS NMR was used to characterize the organic species and monitor the conversion of thiol to propylsulfonic groups. The shape-selective properties of the obtained materials were investigated in acid-catalyzed tetrahydropyranylation reactions. © 2014 Elsevier B.V.

Down to the last detail: Nanostructured solid catalysts were already known in the early 20th century, but their exact structure was unclear. Nowadays, the arrangement of atoms and particles in solids can be manipulated and analyzed down to the atomic scale (see image). The use of specific highly active catalysts enables industrially relevant reactions to be performed at room temperature. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Coking dynamics of Ni-based and Ni-free catalysts were studied in a magnetic suspension thermobalance under methane dry reforming conditions. Ni-rich catalysts undergo strong coking featured with a surface saturation point where the coking rate is drastically reduced. Catalyst resistance towards coking may be enhanced by using noble-metal-based Ni-free precursors or decreasing the Ni content in the catalytic system. The post reaction performed temperature-programmed oxidation experiment of the coked catalyst is diffusion-limited due to large amounts of formed carbon. © 2014 Wiley-VCH Verlag GmbH & Co. KGaA.

Ethanol and oxygen were converted over titania and gold nanoparticles supported on titania to investigate the reactivity of the support, the influence of the metal, and the role of metal-support interactions. In addition to determining the degrees of conversion and the yields as a function of temperature, temperature-programmed desorption and diffuse reflectance infrared spectroscopy were performed in fixed-bed reactors under continuous flow conditions. Over pure TiO2mainly selective oxidative dehydrogenation to acetaldehyde and water and, to a minor extent, total oxidation to CO2and H2O were found to occur above 500 K. The presence of Au nanoparticles additionally induced the selective oxidation to acetaldehyde and H2O at temperatures below 400 K. Thus, the Au/TiO2catalyst shows bifunctional properties in oxygen activation needed for the selective oxidation of ethanol. Ethoxy species were detected by IR spectroscopy, which are identified as intermediate species in ethanol conversion. In contrast, strongly bound acetates and acetic acid acted as catalyst poisons for the selective low-temperature oxidation route but not for the high-temperature route. Selective low-temperature oxidation is assumed to occur at the perimeter of the Au nanoparticles, which additionally enhance the high-temperature oxidation route on TiO2pointing to a Mars-van Krevelen mechanism based on an enhanced reducibility of TiO2. This journal is © the Partner Organisations 2014.

Atom probe tomography (APT) has been used to characterize commercially prepared Pt, Pt/Co alloy, and Ir@Pt core-shell nanoparticles supported on high-surface-area carbon black. Concentration profiles and 3D atom maps revealing the detailed internal structures and compositions of Pt, Pt/Co alloy, and Ir@Pt core-shell particles have been generated, and the distribution of trace impurity elements, including Na and Cl, has been examined. The observation of retained Na on the support, especially in the Pt nanoparticle system, indicates a more rigorous washing procedure is required. In the Pt/Co alloyed carbon-supported nanoparticle system, a marked variation in both compositions and particle sizes is observed. In the case of Ir@Pt, significant intermixing of the Ir core and Pt shell atoms takes place, which would be very difficult to measure by other techniques. All such observations will likely impact the catalytic performance of these materials. We envisage that the single nanoparticle analysis capability of APT, providing atomic-scale structures and chemical mapping, can also act as a means of quality control, identifying differences in the final product compared with the intended specification. Although the catalytic activity of these nanoparticles was not part of current study, the detailed information offered by such studies will permit knowledge-based improvements in nanoscale catalyst preparation methods and will also provide new ways of investigating structure and activity relationships at the nanometer scale. © 2014 American Chemical Society.

Highly stable Ni catalysts with varying Ni contents up to 50 mol% originating from hydrotalcite-like precursors were applied in the dry reforming of methane at 800 and 900 °C. The integral specific rate of methane conversion determined after 10 h on stream was 3.8 mmol s-1 g cat -1 at 900 °C. Due to the outstanding high activity, a catalyst mass of just 10 mg had to be used to avoid operating the reaction in thermodynamic equilibrium. The resulting WHSV was as high as 1.44 × 106 ml gcat -1 h-1. The observed axial temperature distribution with a pronounced cold spot was analyzed by computational fluid dynamics simulations to verify the strong influence of this highly endothermic reaction. Transmission electron microscopy and temperature-programmed oxidation experiments were used to probe the formation of different carbon species, which was found to depend on the catalyst composition and the reaction temperature. Among the formed carbon species, multi-walled carbon nanofibers were detrimental to the long-term stability at 800 °C, whereas their formation was suppressed at 900 °C. The formation of graphitic carbon at 900 °C originating from methane pyrolysis played a minor role. The methane conversion after 100 h of dry reforming at 900 °C compared to the initial one amounted to 98% for the 25 mol% Ni catalyst. The oxidative regeneration of the catalyst was achieved in the isothermal mode using only carbon dioxide in the feed. © the Partner Organisations 2014.

Split second: The photocatalytic activity of gallium oxide (β-Ga 2O3) depends strongly on the co-catalysts CuOx and chromia, which can be efficiently deposited in a stepwise manner by photoreduction of Cu2+ and CrO42-. The water-splitting activity can be tuned by varying the Cu loading in the range 0.025-1.5 wt %, whereas the Cr loading is not affecting the rate as long as small amounts (such as 0.05 wt %) are present. Chromia is identified as highly efficient co-catalyst in the presence of CuOx: it is essential for the oxidation of water. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The faradaic selectivity of the chlorine evolution reaction (CER) and oxygen evolution reaction (OER) on the industrially important Ti-Ru-Ir mixed metal oxide is discussed. Absolute evolution rates as well as volume fractions of Cl2 and O2 were quantified using differential electrochemical mass spectrometry (DEMS), while the catalyst surface redox behavior was analyzed using cyclic voltammetry. The spatial inhomogeneity of the surface catalytic reaction rate was probed using Scanning Electrochemical Microscopy (SECM). Although the nature of the competition between electrochemical discharging of chloride ions and water molecules remains elusive on a molecular scale, new insights into the spatial reactivity distribution of the CER and OER were obtained. Oxidation of water is the initial step in corrosion and concomitant deactivation of the oxide electrodes; however, at the same time the nature of interaction between the oxide surface and water is used as a rational indicator of selectivity and catalytic activity. An experimental procedure was established that would allow the study of selectivity of a variety of different catalyst materials using polycrystalline electrode surfaces. This journal is © the Partner Organisations 2014.

Hydrogenation of esters is vital to the chemical industry for the production of alcohols, especially fatty alcohols that find broad applications in consumer products. Current technologies for ester hydrogenation rely on either heterogeneous catalysts operating under extreme temperatures and pressures or homogeneous catalysts containing precious metals such as ruthenium and osmium. Here, we report the hydrogenation of esters under relatively mild conditions by employing an iron-based catalyst bearing a PNP-pincer ligand. This catalytic system is also effective for the conversion of coconut oil derived fatty acid methyl esters to detergent alcohols without adding any solvent. © 2014 American Chemical Society.

Many photocatalyst systems catalyze chemical reactions under ultraviolet (UV) illumination, because of its high photon energies. Activating inexpensive, widely available materials as photocatalyst using the intense visible part of the solar spectrum is more challenging. Here, nanorod arrays of the wide-band-gap semiconductor zinc oxide have been shown to act as photocatalysts for the aerobic photo-oxidation of organic dye Methyl Orange under illumination with red light, which is normally accessible only to narrow-band semiconductors. The homogeneous, 800-1000-nm-thick ZnO nanorod arrays show substantial light absorption (absorbances >1) throughout the visible spectral range. This absorption is caused by defect levels inside the band gap. Multiple scattering processes by the rods make the nanorods appear black. The dominantly crystalline ZnO nanorod structures grow in the (0001) direction, i.e., with the c-axis perpendicular to the surface of polycrystalline zinc. The room-temperature preparation route relies on controlled cathodic delamination of a weakly bound polymer coating from metallic zinc, an industrially produced and cheaply available substrate. Cathodic delamination is a sequential synthesis process, because it involves the propagation of a delamination front over the base material. Consequently, arbitrarily large sample surfaces can be nanostructured using this approach. © 2014 American Chemical Society.

Highly ordered mesoporous Cu-Ce-O catalysts with different Cu contents have been synthesized by using ordered mesoporous silica KIT-6 as a hard template. The mesostructural order of the negative replica is influenced by the ratio of Cu to Ce. Using XRD, HR-SEM, TEM and EDX analysis, it was found that the ordered mesostructures of the nanocomposites degenerate with increasing Cu concentration, due to CuO leaching during the template removal process and a phase separation at high Cu concentration. Cu ions can replace Ce-ion in the structure of CeO2 at Cu concentrations below 40mol%. However, the Cu concentration in the final materials is lower than expected from the ratio used in the synthesis. The activity in preferential oxidation of CO in H2-rich gases (PROX) was tested at a space velocity of 60,000mLh-1gcat -1. The activity of the mesoporous catalysts increases with the concentration of Cu and becomes stable for Cu concentrations higher than 20mol%. A CO conversion around 100 % can be attained with Cu0.20Ce0.80O2 as catalyst at 160°C. The exit CO concentration can be as low as 70ppm under these conditions. The CO2 selectivity can reach 100 % at low temperature (60- 80°C). Direct loading of CuO on the surface of mesoporous CeO2 leads to large CuO crystals and correspondingly low activity. The influence of the pretreatment atmosphere on activity was also studied. Oxidation-reduction-reoxidation cycling can improve the catalytic activity of the catalysts. © 2014 Elsevier B.V.

Determination of the so-called onset potentials, i.e. the lowest (for the anodic reactions) or the highest (for the cathodic reactions) potentials at which a reaction product is formed at a given electrode and at defined conditions, is very important for the evaluation of the catalytic activity and even more for the comparison of different catalysts. We present an approach for the determination of the onset potentials based on scanning electrochemical microscopy (SECM) using the "substrate generation-tip collection" mode. In the proposed method, the potential applied to the catalyst sample is changed stepwise. A micro-electrode serving as SECM tip is positioned in known close proximity to the catalyst surface and is used to detect the onset of the formation of the product of the catalytic reaction, specifically gas generation at the sample surface. The oxygen evolution reaction (OER) at model RuO 2 and perovskite catalyst surfaces is used to evaluate the approach. The suggested method is supposed to provide a clearer and sensitive means for the detection of the onset potentials of electrolytic gas evolution reactions as compared to conventional procedures which mainly use cyclic voltammetry on stationary or rotating (ring) disk electrodes. Moreover, the detection of the reaction product at the SECM tip allows distinguishing between parasitic reactions at the catalyst surface and the true formation of the anticipated reaction product. © 2013 Elsevier B.V. All rights reserved.

Platinum and platinum alloys supported on carbon materials are the state of the art electrocatalysts for the essential oxygen reduction reaction (ORR) in low-temperature fuel cells. The limited stability of such materials under the often detrimental operation conditions of fuel cells still remains a critical issue to improve. In this work, we explore the impact of nitrogen-doped carbon supports on the activity and stability of platinum-based fuel cell catalysts. We present a nitrogen-doped mesostructured carbon material, nitrogen-doped hollow carbon spheres (NHCS), as a support for platinum-based electrocatalysts. A detailed study of the electrochemical activity and stability was carried out for two Pt@NHCS materials i.e., as-made material (Pt@NHCS) with a Pt particle size smaller than 2 nm and the corresponding material after thermal treatment at 850 °C (Pt@NHCST) with a Pt particle size of ca. 2-3 nm. Activity in the ORR was studied by rotating disc electrode (RDE) thin-film measurements, and electrocatalyst stability was evaluated by accelerated aging tests under simulated start-stop conditions. The performance of the NHCS-based materials was compared to the two corresponding nitrogen-free materials as well as to a standard Pt/Vulcan catalyst. The underlying degradation mechanisms of Pt@NHCS materials were investigated via identical location electron microscopy. Our results conclusively show that nitrogen doping of the carbon supports can offer benefits for achieving high initial mass activities due to improved high platinum dispersion; however, it was not found to necessarily lead to an improvement of the catalyst stability. © 2014 American Chemical Society.

The influence of redox dynamics of a Ni/MgAl oxide catalyst for dry reforming of methane (DRM) at high temperature was studied to correlate structural stability with catalytic activity and coking propensity. Structural aging of the catalyst was simulated by repeated temperature-programmed reduction/oxidation (TPR/TPO) cycles. Despite a very high Ni loading of 55.4 wt.%, small Ni nanoparticles of 11 nm were obtained from a hydrotalcite-like precursor with a homogeneous distribution. Redox cycling gradually changed the interaction of the active Ni phase with the oxide support resulting in a crystalline Ni/MgAl2O4-type catalyst. After cycling the average particle size increased from 11 to 21 nm - while still a large fraction of small particles was present - bringing about a decrease in Ni surface area of 72%. Interestingly, the redox dynamics and its strong structural and chemical consequences were found to have only a moderate influence on the activity in DRM at 900 °C, but lead to a stable attenuation of carbon formation due to a lower fraction of graphitic carbon after DRM in a fixed-bed reactor. Supplementary DRM experiments in a thermobalance revealed that coke formation as a continuous process until a carbon limit is reached and confirmed a higher coking rate for the cycled catalyst. © 2014 Published by Elsevier B.V.

An investigation of the thermal stability of size-selected Au nanoparticles (NPs) synthesized via inverse micelle encapsulation and deposited on SiO 2(4 nm)/Si(100) is presented. The size and mobility of individual Au NPs after annealing at elevated temperatures in ultrahigh vacuum (UHV) was monitored via atomic force microscopy (AFM). An enhanced thermal stability against coarsening and lack of NP mobility was observed up to 1343 K. In addition, a drastic decrease in the average NP height was detected with increasing annealing temperature, which was not accompanied by the sublimation of Au atoms/clusters in UHV. The apparent decrease in the Au NP height observed is assigned to their ability to dig vertical channels in the underlying SiO 2 support. More specifically, a progressive reduction in the thickness of the SiO2 support underneath and in the immediate vicinity of the NPs was evidenced, leading to NPs partially sinking into the SiO2 substrate. The complete removal of silicon oxide in small patches was observed to take place around the Au NPs after annealing at 1343 K in UHV. These results reveal a Au-assisted oxygen desorption from the support via reverse oxygen spillover to the NPs. © 2013 American Chemical Society.

The field of heterogeneous catalysis has received a remarkable amount of interest from scientific and industrial perspectives because of its enormous impact on the world's economy: more than 90% of chemical manufacturing processes use catalysts. Catalysts are also essential in converting hazardous waste into less harmful products (car exhaust) and in generating power (fuel cells). Yet in all applications, it remains a challenge to design long lasting, highly active, selective, and environmentally friendly catalytic materials and processes, ideally based on Earth-abundant elements. In addition, the field needs more satisfactory experimental and theoretical approaches to minimize trial and error experiments in catalyst development.Nanocatalysis is one area that is developing rapidly. Researchers have reported striking novel catalytic properties, including greatly enhanced reactivities and selectivities, for nanocatalysts compared to their bulk counterparts. Fully harnessing the power of nanocatalysts requires detailed understanding of the origin of their enhanced performance at the atomic level, which in turn requires fundamental knowledge of the geometric and electronic structures of these complex systems.Numerous studies report on the properties that affect the catalytic performance of metal naoparticles (NPs) such as their size, interaction with their support, and their oxidation state. Much less research elucidates the role played by the NP shape. Complicating the analysis is that the preceding parameters are not independent, since NP size and support will affect which NP shapes are most stable. In addition, we must consider the dynamic nature of NP catalysts and their response to the environment, since the working state of a NP catalyst might not be the state in which the catalyst was prepared, but rather a structural and/or chemical isomer that responded to the particular reaction conditions. In order to address the complexity of real-world catalysts, researchers must undertake a synergistic approach, taking advantage of a variety of in situ and operando experimental methods. With the continuous shrinking of the scale of material systems, researchers require more sensitive experimental probes and computational approaches that work across a wide range of temperatures and chemical environments.This Account provides examples of recent advances in the preparation and characterization of NP catalysts with well-defined shapes. It discusses how to resolve the shape of nanometer-sized catalysts via a combination of microscopy and spectroscopic approaches, and how to follow their evolution in the course of a chemical reaction. Finally, it highlights that, for structure-sensitive reactions, controlled synthesis can tune catalytic properties such as the reaction rates, onset reaction temperature, activity, and selectivity. © 2012 American Chemical Society.

The ammonia decomposition reaction over molybdenum-based catalysts is an example for the complex influence of different factors, such as phase composition, size of crystalline domains, or defect concentration, on the catalytic behavior of a material. In situ powder diffraction allows the direct analysis of how catalysts change during a reaction with respect to the atomic structure or microstructure in terms of defects or size changes. In this article, the influence of catalyst treatment such as pre-reduction or ball milling on the catalytic properties is discussed in detail. © 2013 Elsevier Inc. All rights reserved.

Many forms of polymers have been prepared and studied as polymeric catalyst support for metal nanoparticles and solid acid catalysts. The nanocasted mesoporous polydivinylbenzene (PDVB)-supported platinum catalysts presented here are distinguished by their customized mesoporosity and bulk morphology that are comparable to typical carbon-and alumina-supported powdered catalysts. Platinum nanoparticles are deposited on PDVB at loadings between 1 wt% and 9 wt% and a mean size between 2.7 nm and 6.2 nm, dependent on the synthesis method. Bifunctional catalysts containing platinum and acidic functionality are prepared by gas-phase sulfonation of the Pt/PDVB catalysts. The PDVB-supported catalysts are active for the oxidation of ethanol with molecular oxygen in water with up to 94% yield of acetic acid. In the analogous oxidation of glycerol, up to 60% yield of glyceric acid is reached with the bifunctional catalyst, and the polymer-supported catalysts feature lower formation of unidentified side products than Pt/C and Pt/Al2O3. Altogether, we find the polymers to be more active than the alumina and more selective than the carbon supports and thus overall have optimized performance. © 2013 Elsevier Ltd. All rights reserved.

We show in this study that the presence of trace metal residues in some supposedly metal-free catalysts for oxygen reduction, at concentrations which are difficult to detect using conventional methods such as XPS and EDX, can profoundly promote the ORR activity of the catalysts. © 2013 Elsevier B.V. All rights reserved.

The strong influence of the support properties on the activity of gold catalysts has been observed in many publications. The most studied reaction in this respect seems to be CO-oxidation, for which gold catalysts have outstanding activity. However, since in most studies the support properties are also important in influencing the nature of the gold particles deposited on them by co-precipitation or deposition-precipitation, it is difficult to study the support effect alone. We have in a series of studies used colloidal impregnation of preformed gold particles approximately 3nm in size on different supports in order to decouple the gold particle formation from the deposition process, in order to isolate the support effect. Even for such similarly prepared catalysts very strong differences between different supports were observed. The analysis of the data, also in the light of literature data, suggests that there is no unique factor explaining the high activity of gold catalysts, but rather a combination of effects, which act in different proportion for different catalysts. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influential support: Metal substrates affect the chemical properties of ZnO layers, which are important catalyst materials for the industrial production of methanol through the oxidation of CO. Interactions with the substrate lead to the formation of a new, planar ZnO thin-film phase, in which less highly oxidized Zn atoms bind CO more strongly than the Zn atoms in the normal wurtzite modification. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

We have investigated the structure and chemical state of size-selected platinum nanoparticles (NPs) prepared by micelle encapsulation and supported on γ-Al2O3 during the oxidation of methanol under oxygen-rich reaction conditions following both oxidative and reductive pretreatments. X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine-structure (EXAFS) spectroscopy measurements reveal that in both cases, the catalyst is substantially oxidized under reaction conditions at room temperature and becomes partially reduced when the reactor temperature is raised to 50 C. Reactivity tests show that at low temperatures, the preoxidized catalyst, in which a larger degree of oxidation was observed, is more active than the prereduced catalyst. We conclude that the differences in reactivity can be linked to the formation and stabilization of distinct active oxide species during the pretreatment. © 2013 American Chemical Society.

Gold nanoparticles have been efficiently photodeposited onto titanate-loaded SBA-15 (Ti(x)/SBA-15) with different titania coordination. Transmission electron microscopy shows that relatively large Au nanoparticles are photodeposited on the outer surface of the Ti(x)/SBA-15 materials and that TiOx tends to form agglomerates in close proximity to the Au nanoparticles, often forming core-shell Au/TiOx structures. This behavior resembles typical processes observed due to strong-metal support interactions. In the presence of gold, the formation of hydrogen on Ti(x)/SBA-15 during the photodeposition process and the performance in the hydroxylation of terephthalic acid is greatly enhanced. The activity of the Au/Ti(x)/SBA-15 materials is found to depend on the TiOx loading, increasing with a larger amount of initially isolated TiO4 tetrahedra. Samples with initially clustered TiOx species show lower photocatalytic activities. When isolated zinc oxide (ZnOx) species are present on Ti(x)/SBA-15, gold nanoparticles are smaller and well dispersed within the pores. Agglomeration of TiOx species and the formation of Au/TiO x structures is negligible. The dispersion of gold and the formation of Au/TiOx in the SBA-15 matrix seem to depend on the mobility of the TiOx species. The mobility is determined by the initial degree of agglomeration of TiOx. Effective hydrogen evolution requires Au/TiOx core-shell composites as in Au/Ti(x)/SBA-15, whereas hydroxylation of terephthalic acid can also be performed with Au/ZnO x/TiOx/SBA-15 materials. However, isolated TiOx species have to be grafted onto the support prior to the zinc oxide species, providing strong evidence for the necessity of Ti-O-Si bridges for high photocatalytic activity in terephthalic acid hydroxylation. © 2013 American Chemical Society.

The influence of the residual growth catalyst on the reducibility and catalytic activity of Pt nanoparticles supported on oxygen- and nitrogen-functionalized CNTs (OCNTs and NCNTs) was systematically investigated. It was found that the presence of the residual growth catalyst significantly influenced the oxygen and nitrogen functionalization of CNTs, which consequently altered the reducibility of the supported Pt nanoparticles. Pt nanoparticles on NCNTs showed a higher stability against sintering in reducing atmosphere at 200 C and 400 C than those on OCNTs. On NCNTs, Pt was in a higher oxidation state and was not as easily reducible as on OCNTs. In hydrogenation catalysis, removing the residual growth catalyst is essential for the supported Pt catalyst to achieve a better performance. Compared with Pt on OCNTs, Pt on NCNTs was less active, but more selective in olefin hydrogenation due to the poisoning effect of the surface nitrogen species. © 2013 Elsevier Inc. All rights reserved.

The redox competition mode of scanning electrochemical microscopy (RC-SECM) was used to study the electrocatalytic activity of three different non-noble metal O2 reduction catalysts at a pH value of 7.4, namely; multi-walled carbon nanotubes (MWCNTs), cobalt protoporphyrin (CoP) and a composite of MWCNTs/CoP. The collection efficiency of a scanning electrochemical microscopy (SECM) tip for the H2O2 generated by the reduction of O2 at the catalyst layer was almost 100%. Consequently, SECM experiments in a combined redox competition and generator/collector mode could be applied for the determination of the number of electrons exchanged during O2 reduction, leading to improved understanding of the intrinsic features of catalyst activity. This approach avoids the typical limitations encountered with rotating ring disk electrode (RRDE) voltammetry, notably, the variation of the quantity of H2O2 in the proximity of the electrode with the speed of electrode rotation or the chemical decomposition of reaction intermediates on the Pt ring, which often introduce inconsistencies and errors in the measured values of the number of exchanged electrons. It is commonly assumed that the O2 reduction reaction on most non-noble metal catalysts proceeds via formation of H2O 2 as an intermediate. The follow-up reaction of H2O 2, typically chemical decomposition or electrochemical reduction, influences the overall number of electrons exchanged during O2 reduction. In this study, we have confirmed by comparing the rate of electrochemical reduction of H2O2 using rotating disk electrode (RDE) measurements with its rate of chemical decomposition studied using a positioned SECM tip, that for the MWCNTs/CoP catalyst, chemical decomposition is predominantly determining the overall number of exchanged electrons per O2 molecule. © 2012 Elsevier B.V.

Structural analysis and catalytic testing revealed that zeolite Beta from template-free synthesis introduces new possibilities in catalysis, as a result of its unprecedentedly high density of active sites with exceptional stability and distinctively ordered nature. Highly active and selective catalysts were obtained either by using it in the Al-rich form (e.g. alkylation) or after post-synthesis treatments (e.g. acylation). Such versatility made possible by this novel synthesis route constitutes a new toolbox for catalysis. © 2013 The Royal Society of Chemistry.

Nitrogen-doped carbon materials were synthesized and used as metal-free electrocatalysts for the oxygen reduction reaction (ORR) under alkaline conditions. The synthesis was achieved by thermal treatment of nitrogen-containing polymers diluted in different carbon materials. Polypyrrole, polyaniline and polyacrylonitrile were used as N precursors. Carbon black and two types of commercial carbon nanotubes were used as carbon matrices. The obtained N contents were in the range of 1-1.8 wt.%. Different N species including pyridinic, pyrrolic and quaternary N were quantitatively determined by X-ray photoelectron spectroscopy. The ORR activities were evaluated in 0.1 M KOH. Rotating disc electrode studies revealed the presence of multiple active centers in all the samples. The sample obtained using polypyrrole and small diameter nanotubes (ca. 15 nm) had the highest onset potential at -0.07 V vs. Ag/AgCl/3 M KCl, which also showed a significantly higher electrochemical stability than the sample from carbon black and polypyrrole. The ORR activity was not correlated to the total nitrogen amount, but to the amount of pyridinic and quaternary N species. For the onset potential and the (Npyridinic + Nquaternary)/Ntotal ratio a quasi-linear relation was found, which points to the substantial role of pyridinic- and quaternary-N species in ORR catalysis. © 2013 Elsevier Ltd. All rights reserved.

Beta zeolite as efficient catalyst has been widely used in industrial processes, and its synthesis is normally performed in the presence of tetraethylammonium hydroxide as organic template. Recent works show successful organotemplate-free and seed-directed synthesis of Beta zeolite (Beta-SDS) in the presence of Beta seeds at 140 C, providing a novel route for synthesizing low-cost zeolite catalysts. Notably, in the case for synthesizing Beta-SDS at 140 C (Beta-SDS140), the use of seeds is still very high (8-10% in silica source) and impurity of MOR zeolite easily appears due to the fast crystallization rate. We demonstrate here a rational synthesis of Beta-SDS at 120 C (Beta-SDS120) with pure BEA structure and improved zeolite quality in the presence of a very small amount of Beta seeds (as low as 1.4%) by decreasing zeolite crystallization rate. X-ray diffraction patterns show that calcination at 550 C for 4 h results in the loss of crystallinity at 8.0% and 15.8% for Beta-SDS120 and Beta-SDS140, respectively, suggesting that Beta-SDS120 has higher thermal stability than Beta-SDS140. N2 adsorption isotherms show that Beta-SDS120 has much higher surface area (655 m2/g) and micropore volume (0.25 cm3/g) than Beta-SDS140 (450 m 2/g, 0.18 cm3/g). These phenomena are reasonably assigned to that Beta-SDS120 samples have much less framework defects such as terminal Si-OH groups than Beta-SDS140. The Beta-SDS120 samples with good crystallinity, high thermal stability, large surface area and pore volume offer a good opportunity for their industrial applications as efficient and low-cost catalytic and adsorptive materials.© 2013 Elsevier Inc. All rights reserved.

Constant COx-free H2 production from the catalytic decomposition of ammonia could be achieved over a high-surface-area molybdenum carbide catalyst prepared by a temperature-programmed reduction-carburization method. The fresh and used catalyst was characterized by N2 adsorption/desorption, powder X-ray diffraction, scanning and transmission electron microscopy, and electron energy-loss spectroscopy at different stages. Observed deactivation (in the first 15 h) of the high-surface-area carbide during the reaction was ascribed to considerable reduction of the specific surface area due to nitridation of the carbide under the reaction conditions. Theoretical calculations confirm that the N atoms tend to occupy subsurface sites, leading to the formation of nitride under an NH3 atmosphere. The relatively high rate of reaction (30 mmol/((g of cat.) min)) observed for the catalytic decomposition of NH3 is ascribed to highly energetic sites (twin boundaries, stacking faults, steps, and defects) which are observed in both the molybdenum carbide and nitride samples. The prevalence of such sites in the as-synthesized material results in a much higher H2 production rate in comparison with that for previously reported Mo-based catalysts. © 2013 American Chemical Society.

Oxygen- and nitrogen-functionalized carbon nanotubes (OCNTs and NCNTs) were applied as metal-free catalysts in selective olefin hydrogenation. A series of NCNTs was synthesized by NH3 post-treatment of OCNTs. Temperature-programmed desorption, N2 physisorption, Raman spectroscopy, high-resolution transmission electron microscopy and X-ray photoelectron spectroscopy were employed to characterize the surface properties of OCNTs and NCNTs, aiming at a detailed analysis of the type and amount of oxygen- and nitrogen-containing groups as well as surface defects. The gas-phase treatments applied for oxygen and nitrogen functionalization at elevated temperatures up to 600 °C led to the increase of surface defects, but did not cause structural damages in the bulk. NCNTs showed a clearly higher activity than the pristine CNTs and OCNTs in the hydrogenation of 1,5-cyclooctadiene, and also the selectivity to cyclooctene was higher. The favorable catalytic properties are ascribed to the nitrogen-containing surface functional groups as well as surface defects related to nitrogen species. In contrast, oxygen-containing surface groups and the surface defects caused by oxygen species did not show clear contribution to the hydrogenation catalysis. Copyright © 2013, Dalian Institute of Chemical Physics, Chinese Academy of Sciences.

Incisive modulation of the intermolecular hardness between metalloporphyrins and O2 can lead to the identification of promising catalysts for oxygen reduction. The dependency of the electrocatalytic reduction of O2 by metalloporphyrins on the nature of the central metal yields a volcano-type curve, which is rationalized to be in accordance with the Sabatier principle by using an approximation of the electrophilicity of the complexes. By using electrochemical and UV/Vis data, the influence of a selection of meso-substituents on the change in the energy for the π→π* excitation of manganese porphyrins was evaluated allowing one to quantitatively correlate the influence of the various ligands on the electrocatalysis of O2 reduction by the complexes. A manganese porphyrin was identified that electrocatalyzes the reduction of oxygen at low overpotentials without generating hydrogen peroxide. The activity of the complex became remarkably enhanced upon its pyrolysis at 650 °C. Finding the strength: Incisive modulation of the intermolecular hardness between metalloporphyrins and O2 can lead to the identification of promising catalysts for the oxygen reduction reaction (see figure). The feasibility of this principle is demonstrated in the selection and design of a manganese metalloporphyrin with promising high activity for electrocatalytic oxygen reduction. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Best of both worlds: PtxPdy, Pt, and Pd aerogels with high surface area and porosity can be synthesized in a controlled fashion by a straightforward and environmentally benign strategy. These materials, which are highly active and stable catalysts for the oxygen reduction reaction in PEFC cathodes, combine the high stability of extended surfaces with the high surface area of nanoparticles. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Critical factors for the commercial application of fuel cells are the high costs and the limited stability of Pt catalysts. In order to improve the activity and material efficiency, Pt-alloys with nonnoble metals play an essential role. However, stability remains a critical factor for this type of catalysts. In order to understand the dissolution of Pt-alloys and eventually improve their performance, we therefore analyze a Pt-Cu thin-film alloy with varying composition using a combinatorial screening approach coupled to online analytics. © The Electrochemical Society.

Water-assisted growth of multiwalled carbon nanotubes (CNTs) was studied over a Co-based catalyst under plug-flow conditions. The influence of water concentration and temperature on the growth kinetics within the first 300 s was analyzed by measuring the conversion of ethylene. Feeding 200 ppm H2O vapor at 650 C accelerated the initial growth rate and extended the mean lifetime of the catalytically active sites. Higher water concentrations of up to 500 ppm led to lower growth rates and lower CNT yields. Water of 200 ppm showed a promoting effect at 650 C, but an inhibiting effect at 550 C. The CO generated by steam gasification of deposited carbon was monitored online indicating coking of the catalyst. The results demonstrate that water plays a dual role: the removal of amorphous carbon on the catalyst by gasification and partial oxidation of the metallic Co catalyst. Water also influenced the diameter distribution of the CNTs. © 2013 American Chemical Society.

Solid surfaces generally respond sensitively to their environment. Gas phase or liquid phase species may adsorb and react with individual surface atoms altering the solid-gas and solid-liquid electronic and chemical properties of the interface. A comprehensive understanding of chemical and electrochemical interfaces with respect to their responses to external stimuli is still missing. The evolution of the structure and composition of shape-selected octahedral PtNi nanoparticles (NPs) in response to chemical (gas-phase) and electrochemical (liquid-phase) environments was studied, and contrasted to that of pure Pt and spherical PtNi NPs. The NPs were exposed to thermal annealing in hydrogen, oxygen, and vacuum, and the resulting NP surface composition was analyzed using X-ray photoelectron spectroscopy (XPS). In gaseous environments, the presence of O2 during annealing (300 °C) lead to a strong segregation of Ni species to the NP surface, the formation of NiO, and a Pt-rich NP core, while a similar treatment in H2 lead to a more homogenous Pt-Ni alloy core, and a thinner NiO shell. Further, the initial presence of NiO species on the as-prepared samples was found to influence the atomic segregation trends upon low temperature annealing (300 °C). This is due to the fact that at this temperature nickel is only partially reduced, and NiO favors surface segregation. The effect of electrochemical cycling in acid and alkaline electrolytes on the structure and composition of the octahedral PtNi NPs was monitored using image-corrected high resolution transmission electron microscopy (TEM) and high-angle annular dark field scanning TEM (HAADF-STEM). Sample pretreatments in surface active oxygenates, such as oxygen and hydroxide anions, resulted in oxygen-enriched Ni surfaces (Ni oxides and/or hydroxides). Acid treatments were found to strongly reduce the content of Ni species on the NP surface, via its dissolution in the electrolyte, leading to a Pt-skeleton structure, with a thick Pt shell and a Pt-Ni core. The presence of Ni hydroxides on the NP surface was shown to improve the kinetics of the electrooxidation of CO and the electrocatalytic hydrogen evolution reactions. The affinity to water and the oxophilicity of Ni hydroxides are proposed as likely origin of the observed effects. © 2013 The Royal Society of Chemistry.

Design and fabrication of semiconductor based composite photocatalysts with matching band structure is an important strategy to improve charge separation of photogenerated electron-hole pairs for photocatalytic hydrogen production. In our study, by aid of the simple and cost-effective molten salts method, a series of phase-controlled and composition-tuned calcium tantalate composite photocatalysts has been prepared by adjusting the initial atomic ratio of Ta/Ca precursors. We demonstrate the strong correlation between the photocatalytic activities of calcium tantalate composite photocatalysts for hydrogen evolution and respective phase compositions. Without any cocatalysts, these composites with the optimized phase composition of cubic α-CaTa2O 6/hexagonal Ca2Ta2O7, cubic CaTa2O6/hexagonal Ca2Ta2O 7/orthorhombic β-CaTa2O6, or cubic α-CaTa2O6/orthorhombic β-CaTa2O 6 showed very high photocatalytic H2 production activities in the presence of methanol. It is attributed mainly to a significantly improved photoexcited charge carrier separation via the junctions and interfaces in the composites. Further by in situ photodeposition of noble metal nanoparticles (Pt or Rh) as cocatalysts the photocatalytic activity of these composites was greatly promoted for H2 production. The study on convenient fabrication of phase-coexisting composite photocatalysts with matching band structure for improving the photocatalytic hydrogen production sheds light on developing efficient composite photocatalyst as a means for conversion of solar energy to chemical energy. © 2013 American Chemical Society.

2-Propanol and oxygen were converted over titania and gold nanoparticles supported on titania to investigate the reactivity of the support, the influence of the metal and the role of metal-support interactions. The catalysts were characterized by N2 physisorption and transmission electron microscopy. In addition to deriving the degrees of conversion and the yields as a function of temperature, temperature-programmed desorption and diffuse reflectance infrared spectroscopy were applied in fixed-bed reactors under continuous flow conditions. Over pure TiO2 above 500K the acid-base catalyzed dehydration yielding propene and water, the dehydrogenation to acetone and H2, and the oxidative dehydrogenation to acetone and water were found to occur. The additional presence of Au nanoparticles induced the selective oxidation to acetone and H2O at temperatures below 400K, whereas the selective oxidation to acetone at higher temperatures above 500K was also observed on pure TiO2. Also the dehydration of 2-propanol to propene and H2O and, to a minor extent, the total oxidation to CO2 and H2O were catalyzed by Au/TiO2. Therefore, the Au/TiO2 catalyst shows bifunctional properties in oxygen activation needed for the selective oxidation of 2-propanol. 2-propoxide species were detected by IR spectroscopy, which are identified as intermediate species in 2-propanol conversion, whereas strongly bound acetates and carbonates acted as catalyst poison for the selective low-temperature oxidation route, but not for the high-temperature route. Selective low-temperature oxidation is assumed to occur at the perimeter of the Au nanoparticles, which also enhance the high-temperature oxidation route on TiO2 pointing to a Mars-van Krevelen mechanism based on an enhanced reducibility of TiO2. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A major practical challenge in heterogeneous catalysis is to minimize the loading of expensive platinum group metals (PGMs) without degrading the overall catalytic efficiency. Gaining a thorough atomic-scale understanding of the chemical/structural changes occurring during catalyst manufacture/operation could potentially enable the design and production of "nano-engineered" catalysts, optimized for cost, stability and performance. In the present study, the oxidation behavior of a Pt-31 at% Pd alloy between 673-1073. K is investigated using atom probe tomography (APT). Over this range of temperatures, three markedly different chemical structures are observed near the surface of the alloy. At 673. K, the surface oxide formed is enriched with Pd, the concentration of which rises further following oxidation at 773. K. During oxidation at 873. K, a thick, stable oxide layer is formed on the surface with a stoichiometry of PdO, beneath which a Pd-depleted (Pt-rich) layer exists. Above 873. K, the surface composition switches to enrichment in Pt, with the Pt content increasing further with increasing oxidation temperature. This treatment suggests a route for tuning the surfaces of Pt-Pd nanoparticles to be either Pd-rich or Pt-rich, simply by adjusting the oxidation temperatures in order to form two different types of core-shell structures. In addition, comparison of the oxidation behavior of Pt-Pd with Pt-Rh and Pd-Rh alloys demonstrates markedly different trends under the same conditions for these three binary alloys. © 2012.

A new synthetic route to acidic polystyrene-co-divinylbenzene resin catalysts allows systematic variation of cross-linker content, porosity, and acid site density. These resins are prepared in the form of powders by nanocasting, and the acid site density and the distribution of the acid sites in the prepared catalysts is controlled by liquid phase sulfonation with adjusted mixtures of sulfuric acid and oleum. This method allows identical synthesis conditions for the entire range of cross-linker content. With this set of model catalysts, the cross-linker content of the resin was found to be the most influential factor for the liquid phase dehydration of fructose to 5-hydroxymethylfurfural. © 2012 American Chemical Society.

Methanol oxidation was used as test reaction to investigate the influence of the metal, of the support, and of metal-support interactions in Au/ZnO and Au/TiO2 catalysts. Catalytic measurements as well as infrared spectroscopy were applied under continuous flow conditions in fixed-bed reactors. A strong effect of the Au loading ranging from 0.6 wt.% to 1.9 wt.% was found for both Au/ZnO and Au/TiO2 catalysts with Au particle sizes in the range from 3 to 7 nm. Methanol combustion yielding H2O and CO2 was the main reaction path, but also reactions such as partial oxidation of methanol, steam reforming of methanol, methanol decomposition as well as the selective oxidation of methanol to methyl formate, formaldehyde, or dimethoxymethane were found to occur. Smaller Au particles and a higher amount of small Au particles had a beneficial effect on the activity. Infrared spectroscopy identified methoxy species adsorbed on the metal oxides as intermediates in methanol oxidation. The product distribution was found to depend on the oxide used as support due to the different Lewis acidities. On Au/TiO2, strongly bound formates acted as reversible catalyst poison. The catalytic activity was found to be correlated with the number of Au atoms at the perimeter of the Au nanoparticles. Correspondingly, oxygen activation is assumed to occur at their perimeter, and the oxide provides methoxy species reacting at the interface. © 2012 Elsevier Inc. All rights reserved.

A setup for optically monitoring the agglomerate growth of multiwalled carbon nanotubes (MWCNTs) by catalytic chemical vapor deposition on single Co-Mn-Al-Mg oxide catalyst particles with ethene as carbon precursor has been developed. Ethene concentrations and temperatures were varied between 5. -75. Vol.% and 550-770. °C, respectively. It could be shown that the agglomerate growth is rapid and the final diameter is reached after a few ten seconds to about 3. min depending on the reaction conditions. The average enlargement factor of the agglomerates over all experiments was found to be 6.5. ±. 1.2 compared to the original diameter of the catalyst particle. The growth rate is enhanced by both, reaction temperature and ethene concentration. Hence it is concluded that the agglomerate growth rate is associated with the reaction rate of MWCNT synthesis. Short time experiments and analysis of the resulting agglomerates have confirmed an earlier proposed growth mechanism. © 2013 Elsevier B.V.

Nitrogen-doped carbon nanotubes (NCNTs) are highly active electrocatalysts in the oxygen reduction reaction (ORR) at alkaline conditions. However, the initial activation and stabilization of NCNTs have rarely been investigated at industrially relevant conditions. Three types of NCNTs were synthesized by catalytic growth (NCNT-growth) or posttreatment of oxygen-functionalized CNTs with NH3 (NCNT-NH3) or aniline (NCNT-aniline). The obtained NCNTs were treated in 10 M KOH at 80 C for 5 h, and the formation of oxygen groups by alkaline treatment and their interaction with existing nitrogen groups was analyzed. X-ray photoelectron spectroscopy showed that the concentrations of pyridinic and quaternary nitrogen increased in NCNT-growth due to the KOH treatment accompanied by the decrease of pyrrolic nitrogen, whereas the nitrogen groups changed differently in NCNT-NH3 and NCNT-aniline. NCNT-NH3 showed the highest ORR activity before alkaline treatment. After the treatment, the activity of NCNT-growth was higher, whereas those of NCNT-NH3 and NCNT-aniline were lower. These results were found to be correlated with changes in the nitrogen groups caused by alkaline treatment. Furthermore, NCNTs showed different C=O/C-O ratios after alkaline treatment as compared to a strong increase of C-O in CNTs, indicating that the presence of nitrogen in NCNTs influences the formation of oxygen groups on carbon and surface oxidation. © 2013 American Chemical Society.

An overview of work with model systems designed to study metal-support interactions in heterogeneous catalysts is given. In these models, metal and support are both miniaturized by introduction as guests into a mesoporous host. The use of such models is demonstrated with Au-TiO2 clusters encaged in MCM-48, and Cu-ZnO clusters encapsulated in siliceous mesopore systems and in carbon nanotubes. The models promise a better opportunity to track changes in the support component during catalyst activation and catalysis, including the action of poisons that may at first be trapped on the support surface. Challenges to be met are the stabilization of the mesoporous matrix during synthesis and catalysis, possible reactivity of the matrix surface towards any of the catalyst components, as well as clustering and segregation of the latter from the matrix. The challenges were encountered as pore damage during preparation of Au-TiO2/MCM-48 catalysts, as deactivating interactions of siliceous walls with zinc ions during deposition of zinc species from aqueous media, and as clustering of the Cu component during calcination and reduction. Among the conclusions drawn from the studies are the irrelevance of order at the Au-TiO2 interface (and, hence, of epitaxy and of crystal strain in gold) for high activity of Au/TiO2 catalysts in CO oxidation. In the models for Cu-ZnO methanol synthesis catalysts, two different types of Cu-Zn interaction could be observed: a direct contact between Zn2+ and Cu(0) under strong reducing conditions, and the formation of alloy nanoparticles (nano-brass). A discussion of the relevance of these interactions for the methanol synthesis reaction is given. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The initial growth kinetics of multi-walled carbon nanotubes (CNTs) was investigated using a highly active Co-based mixed-oxide catalyst in a tubular fixed-bed reactor under plug-flow conditions with ethene as carbon source. The growth temperature and the ethene concentration were systematically varied in the range from 758 to 923 K and from 5 to 45 vol.%, respectively. The carbon mass accumulation was derived from the ethene conversion and analyzed by a kinetic model, from which the initial CNT growth rate and the mean lifetime of the active sites were derived permitting the prediction of the maximum theoretical CNT yield. With increasing growth temperatures up to 923 K both the initial growth rate and the mean lifetime of active sites increased strongly with a significantly prolonged lifetime above 848 K. The initial growth rate was slow at lower ethene concentrations, but the mean life time was very high. Increasing the ethene concentration up to 45 vol.% led to a much higher initial growth rate, but shortened the mean lifetime strongly. Due to the fast deactivation at high ethene concentrations, the predicted maximum yield decreased considerably approaching the yield obtained after 5 min of time on stream. © 2013 Elsevier Ltd. All rights reserved.

The deposition of hydrogen evolution sites on photocatalysts is a crucial step in the multistep process of synthesizing a catalyst that is active for overall photocatalytic water splitting. An alternative approach to conventional photodeposition was developed, applying the photocatalytic reforming of aqueous methanol solutions to deposit metal particles on semiconductor materials such as Ga2O3 and (Ga0.6Zn0.4)(N 0.6O0.4). The method allows optimizing the loading of the co-catalysts based on the stepwise addition of their precursors and the continuous online monitoring of the evolved hydrogen. Moreover, a synergetic effect between different co-catalysts can be directly established. © 2012 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A hierarchical carbon-fiber composite was synthesized based on carbon cloth (CC) modified with primary carbon microfibers (CMF) and subsequently secondary carbon nanotubes (CNT), thus forming a three-dimensional hierarchical structure with high BET surface area. The primary CMFs and the secondary CNTs are grown with electrodeposited iron nanoparticles as catalysts from methane and ethylene, respectively. After deposition of Pt nanoparticles by chemical vapor deposition from (trimethyl)cyclopentadienylplatinum, the resulting hierarchical composite was used as catalyst in the electrocatalytic oxygen reduction (oxygen reduction reaction, ORR) as specific test reaction. The modification of the CC with CMFs and CNTs improved the electrochemical properties of the carbon composite as revealed by electrochemical impedance measurements evidencing a low charge transfer resistance for redox mediators at the modified CC. X-ray photoelectron spectroscopy measurements were carried out to identify the chemical state and the surface atomic concentration of the Pt catalysts deposited on the hierarchical carbon composites. The ORR activity of Pt supported on different composites was investigated using rotating disk electrode measurements and scanning electrochemical microscopy. These electrochemical studies revealed that the obtained structured catalyst support is very promising for electrochemical applications, e.g. fuel cells. © 2012 Elsevier Ltd. All rights reserved.

ORR MNC, FTW! Mesoporous nitrogen-rich carbon (MNC) materials are synthesized by using polymer-loaded SBA-15 pyrolyzed at different temperatures. The activity and stability of the catalysts in the oxygen reduction reaction (ORR) are investigated by using cyclic voltammetry and rotating-disk electrode measurements. The MNC material pyrolyzed at 800 °C exhibits a high electrocatalytic activity towards the ORR in alkaline medium. © 2012 Wiley-VCH Verlag GmbH&Co. KGaA, Weinheim.

Mesoporous copper-alumina (Cu-Al 2O 3) with different copper contents was synthesized in a one-pot reaction via the evaporation-induced self-assembly of Pluronic P123 and the corresponding metal precursors in ethanolic solution in the presence of nitric acid. Mesoporous Cu-Al 2O 3 calcined at 400°C exhibits a large BET surface area of 265 m 2/g and a pore volume of 0.48 cm 3/g. XRD results indicate that the wall of mesoporous Cu-Al 2O 3 calcined at 400°C is amorphous, and that it is transformed to crystalline material by further thermal treatment at 800°C. Copper was formed as very small particles in the composite under 5% H 2 flow at high temperature. Moreover, the mesoporous structure did not collapse after the sample was reduced at 650°C for 4 h, and the copper particles with sizes of around 6 nm were well distributed through the entire mesoporous γ-Al 2O 3 network. Using the mesoporous Cu/γ-Al 2O 3 as a bifunctional catalyst for one-step dimethyl ether synthesis from synthesis gas, a CO conversion of 72% and a DME selectivity of 69% were obtained at 50 bar and 310°C. © 2012 Elsevier Inc. All rights reserved.

Benzene can be activated by visible light (λ > 455 nm) in the presence of TiO2, which leads to formation of carbonaceous polymeric deposits on the titania surface. These photosynthesized surface-modified materials exhibit enhanced photoactivity in degradation of phenolic compounds, particularly under visible light irradiation. © 2012 The Royal Society of Chemistry.

The reaction path of the Cl 2 evolution reaction (CER) was investigated by combining electrochemical and spectroscopic methods. It is shown that oxidation and reconstruction of the catalyst surface during CER is a consequence of the interaction between RuO 2 and water. The state of the RuO 2 surface during the electrochemical reaction was analyzed in situ by using Raman spectroscopy to monitor vibrations of the crystal lattice of RuO 2 and changes in the surface concentration of the adsorbed species as a function of the electrode potential. The role of the solvent was recognized as being crucial in the formation of an oxygen-containing hydrophilic layer, which is a key prerequisite for electrocatalytic Cl 2 formation. Water (more precisely the OH adlayer) is understood not just as a medium that allows adsorption of intermediates, but also as an integral part of the intermediate formed during the electrochemical reaction. New insights into the general understanding of electrocatalysis were obtained by utilizing the vibration frequencies of the crystal lattice as a dynamic catalytic descriptor instead of thermodynamic descriptors, such as the adsorption energy of intermediates. Interpretation of the derived "volcano" curve suggests that electrocatalysis is governed by a resonance phenomenon. Water powered! The reaction path of the Cl 2 evolution reaction (CER) is investigated by combining electrochemical and spectroscopic methods. Oxidation and reconstruction of the catalyst surface during CER is a consequence of the interaction between RuO 2 and water. Interpretation of the derived volcano curve suggests that electrocatalysis is governed by a resonance phenomenon (see picture). © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The search for more stable electrocatalyst materials for electrochemical energy conversion requires a fundamental understanding of the underlying degradation processes. Advanced characterization techniques like identical location transmission electron microscopy (IL-TEM) can provide invaluable insight into the stability of electrode materials on the nanoscale. In this review, the basic principles and the methodology of IL-TEM are described, and its capabilities are revealed by demonstrating the recent progress that has been achieved in research on the stability of fuel cell catalysts. Moreover, we provide future perspectives of the identical location approach towards implementing other electron microscopic and tomographic applications, which will help us to gain an even broader view of the degradation of electrocatalysts. © 2012 The Royal Society of Chemistry.

A simple method is presented for the formation of thin films of Cu-Pt(111) near-surface alloys (NSA). In these thin films, the solute metal (Cu) is preferentially located in the second platinum layer and protected by a Pt surface layer. The NSA-films act as active and fairly stable electrocatalysts for the reduction of oxygen with the activity and stability which approach those for bulk single crystalline Pt-alloy surfaces and ∼5 times more active than state-of-the-art Pt thin films. © 2012 American Chemical Society.

In this review, we describe and discuss the developments in the use of metalloporphyrins and metallophthalocyanines as catalysts for oxygen reduction in aqueous electrolytes. The main goal of most researchers in this field has been to design catalysts which can achieve facile reduction of oxygen by the four-electron transfer pathway at the lowest overpotential possible. With this in mind, the primary objective of this review was to bring to light the research frontiers uncovering important milestones towards the synthesis and design of promising N 4-metallomacrocyclic catalysts which accomplish the four-electron reduction of oxygen, and, based on literature, to draw attention to the fundamental requirements for synthesis of improved catalysts operating at low overpotentials. Our emphasis was not to make parallel comparisons between individual classes of N 4-metallomacrocyclic complexes with respect to their activity, but rather to focus on the commonalities of the fundamental properties that govern their reactivities and how these may be aptly manipulated to develop better catalysts. Therefore, besides discussion of the progress attained with regard to synthesis and design of catalysts with high selectivity towards four-electron reduction of O 2, a major part of the review highlights quantitative structure-activity relationships (QSAR) which govern the activity and stability of these complexes, which when well understood, refined and carefully implemented should constitute a fundamental gateway for rational design of better catalysts. Copyright © 2012 World Scientific Publishing Company.

Metallic copper nanoparticles have been efficiently dispersed and stabilized on nitrogen-doped carbon nanotubes. They are about 8-10 nm in diameter and highly resistant against bulk oxidation. Their catalytic activity and recyclability have been investigated in A 3-type coupling reactions for the synthesis of propargylamines. It was easily possible to prepare diastereomerically pure derivatives of proline and to efficiently recover and reuse the supported catalyst several times. © 2012 Elsevier B.V. All rights reserved.

The gasification of carbon with CO 2 was applied to examine the role of the residual iron growth catalyst in multi-walled carbon nanotubes (CNTs), which were pre-treated either by refluxing in nitric acid at 120 °C or by nitric acid vapor at 200 °C. Temperature-programmed desorption (TPD) and surface reaction (TPSR) experiments were performed in He and CO 2, respectively. The Fe nanoparticles were retained after the treatment in HNO 3 vapor, whereas the liquid HNO 3 treatment was able to remove the accessible residual Fe catalyst. The exposed Fe nanoparticles were found to catalyze the gasification of CNTs with CO 2 according to the reverse Boudouard reaction C + CO 2 = 2CO. In case of the CNTs pretreated in HNO 3 vapor, evolving CO 2 formed due to the decomposition of oxygen-containing functional groups during the TPD experiments was fully converted above 750 °C into desorbing CO, and the addition of 2000 ppm CO 2 in the feed gas during the TPSR experiments resulted in full conversion at 1000 °C. X-ray photoelectron spectroscopy studies show that the treatment in HNO 3 vapor at 200 °C favors the formation of oxygen species doubly bound to carbon (CO groups). During the TPSR experiments, CO 2 as a weak oxidant partially oxidized the CNTs leading to the formation of CO groups, and a much higher amount of these groups was detected on HNO 3 vapor-treated CNTs with residual Fe catalyst. Their presence suggests that CO groups are reaction intermediates of the CNT gasification with CO 2, which is considered an effective test reaction for the presence of residual catalytically active nanoparticles. © 2012 Elsevier B.V.

Adsorption and oxidation of CO on Au/ZnO catalysts were studied by Fourier transform infrared (FTIR) spectroscopy using a novel ultra-high-vacuum (UHV) system. The high-quality UHV-FTIRS data provide detailed insight into the catalytic mechanism of low-temperature CO oxidation on differently pretreated Au/ZnO catalysts. For the samples without O 2 pretreatment, negatively charged Au nanoparticles are identified which exhibit high reactivity to CO oxidation at 110 K, yielding CO 2 as well as carbonate species bound to various ZnO facets. O 2 pretreatment leads to formation of neutral Au nanoparticles where CO is activated on the low-coordinated Au sites at the interface. Activation of impinging O 2 occurs at the Au/ZnO interface and is promoted by preadsorbed CO forming an OC-O 2 intermediate complex, accompanied by charge transfer from Au/ZnO substrate to O 2. The CO molecules adsorbed on ZnO serve as a reservoir for reactants and are mobile enough at 110 K to reach the Au/ZnO interface where they react with activated oxygen yielding CO 2. Different carbonate species are further produced via interaction of formed CO 2 with surface oxygen atoms on ZnO. It was found that the active interface sites are slowly blocked at 110 K by the inert carbonate species, thus causing a gradual decrease of the catalytic activity. © 2012 American Chemical Society.

Gold nanoparticles supported on transition metal oxides are found to exhibit a pronounced particle size effect in CO oxidation. However, the preparation of comparable supported gold nanoparticles with different sizes remains challenging, since the catalytic behavior of these materials is very sensitive to the preparation conditions. To overcome this difficulty, Au, @ZrO 2 catalysts with gold core sizes between 5 and 15 nm were prepared by partial leaching of gold in an ex-post manner. The material obtained offers a unique comparability for particle size effect studies in CO oxidation. No effect of gold particle size was observed in the studied size range. © 2012 Elsevier Inc. All rights reserved.

This manuscript investigates the degradation of a Pt/Vulcan fuel cell catalyst under simulated start-stop conditions in an electrochemical half-cell. Identical location transmission electron microscopy (IL-TEM) is used to visualize the several different degradation pathways occurring on the same catalyst material under potential cycling conditions. The complexity of degradation on the nanoscale leading to macroscopic active surface area lossis demonstrated and discussed. Namely, four different degradation pathways at one single Pt/Vulcan aggregate are clearly observed. Furthermore, inhomogeneous degradation behavior for different catalyst locations is shown, and trends in degradation mechanisms related to the platinum particle size are discussed in brief. Attention is drawn to the vast field of parameters influencing catalyst stability. We also present the development of a new technique to study changes of the catalyst not only with 2D projections of standard TEM images but also in 3D. For this purpose, identical location tomography (IL-tomography) is introduced, which visualizes the 3D structure of an identical catalyst location before and after degradation. © 2012 American Chemical Society.

This work presents a new approach for synthesis of oxygen reduction catalysts constituted of a transition metal, nitrogen and carbon, by thermal treatment of electrochemically synthesized metal-polypyrrole (M-PPy) composites on glassy carbon electrodes. The synthesis procedure involves immobilization of PPy on glassy carbon followed by dosing of metal (M = Mn, Fe and Co) particles, alternately, by electropolymerization and electrochemical reduction respectively. Electrochemical characterization by cyclic voltammetry (CV) and hydrodynamic rotating disk electrode (RDE) measurements show that the M-PPy composites inherently catalyse the electroreduction of oxygen under acidic conditions. The activity of the composites is significantly augmented when they are heat treated at high temperatures (450-850 °C) under a continuous flow of nitrogen. The presence of metallic entities within the M-PPy composite structures and in the structures ensuing after heat treatment was confirmed by energy dispersive X-ray (EDX) analysis. © 2011 Elsevier Ltd. All rights reserved.

Pt-based alloys containing Rh and Ru are effective catalysts in a range of applications, including pollution control and low-temperature fuel cells. As the Pt group metals are generally rare and expensive, minimizing the loading of them while also increasing the efficiency of catalyst materials is a continual challenge in heterogeneous catalysis. A smart method to "nanoengineer" the surface of the nanocatalyst particles would greatly aid this goal. In our study, the oxidation of a Pt-8.9 at. % Ru alloy between 773 and 973 K and the oxidation and oxidation/reduction behavior of a Pt-23.9 at. % Rh-9.7 at. % Ru alloy at 873 K for various exposure times were studied using atom probe tomography. The surface of the Pt-Ru alloy is enriched with Ru after oxidation at 773 K, whereas it is depleted in Ru at 873 K, and at 973 K. The surface oxide layer vanishes at higher temperatures, leaving behind a Pt-rich surface. In the case of the Pt-Rh-Ru alloy, oxidation initiates from the grain boundaries, forming an oxide with a stoichiometry of MO 2. As the oxidation time increases, this oxide evolves into a twophase nanostructure, involving a Rh-rich oxide phase (Rh, Ru) 2O 3 and a Ru-rich oxide phase (Ru, Rh)O 2. When this two-phase oxide is reduced in hydrogen at low temperatures, separate Rh-rich and Ru-rich nanoscale regions remain. This process could, therefore, be useful for synthesizing complex island structures on Pt-Rh-Ru nanoparticle catalysts. © 2012 American Chemical Society.

The possible role of ammonia in a future energy infrastructure is discussed. The review is focused on the catalytic decomposition of ammonia as a key step. Other aspects, such as the catalytic removal of ammonia from gasification product gas or direct ammonia fuel cells, are highlighted as well. The more general question of the integration of ammonia in an infrastructure is also covered. © 2012 The Royal Society of Chemistry.

The durability of electrode materials is a limiting parameter for many electrochemical energy conversion systems. In particular, electrocatalysts for the essential oxygen reduction reaction (ORR) present some of the most challenging instability issues shortening their practical lifetime. Here, we report a mesostructured graphitic carbon support, Hollow Graphitic Spheres (HGS) with a specific surface area exceeding 1000 m2 g-1 and precisely controlled pore structure, that was specifically developed to overcome the long-term catalyst degradation, while still sustaining high activity. The synthetic pathway leads to platinum nanoparticles of approximately 3 to 4 nm size encapsulated in the HGS pore structure that are stable at 850 C and, more importantly, during simulated accelerated electrochemical aging. Moreover, the high stability of the cathode electrocatalyst is also retained in a fully assembled polymer electrolyte membrane fuel cell (PEMFC). Identical location scanning and scanning transmission electron microscopy (IL-SEM and IL-STEM) conclusively proved that during electrochemical cycling the encapsulation significantly suppresses detachment and agglomeration of Pt nanoparticles, two of the major degradation mechanisms in fuel cell catalysts of this particle size. Thus, beyond providing an improved electrocatalyst, this study describes the blueprint for targeted improvement of fuel cell catalysts by design of the carbon support. © 2012 American Chemical Society.

Platinum group metals (PGMs) are used in numerous catalyst applications, including conversion of engine exhaust gases and hydrocarbon reforming. Reducing the loading of PGMs without diminishing the overall catalyst activity is a major challenge. Fundamental studies of PGMs under reactive conditions can assist the design/synthesis of "nanoengineered" catalysts, tunable and optimized for cost, stability, and performance. In the present study, the oxidation and reduction behavior of a Pd-6.4 at. % Rh alloy is investigated following treatment at 873 K for various exposure times using atom-probe tomography. For short oxidation times (10 min), an oxide layer with PdO stoichiometry grows on the surface. As the oxidation time increases, two phases with stoichiometries of (Rh 1Pd 1)O 2 and (Pd 2O) evolve. When the alloy is subsequently reduced in hydrogen, a nanoscale dispersion of Rh-rich metallic regions remains. This provides a route for the synthesis of multifunctional catalysts with different nanosurface regions in close proximity to one another. © 2012 American Chemical Society.

The activities of four different samples of dimensionally stable anodes (DSA) for the Cl 2 evolution reaction (CER) were analysed and compared with respect to their geometric properties. The samples were made from the same catalyst material, namely mixed oxides of TiO 2 and RuO 2 supported on Ti, following a preparation method in which variations in morphological features of the obtained electrodes were caused by the tensile stress imposed on each sample. The study revealed intriguing correlations between activity, surface area and characteristic morphological features. It is demonstrated that a large number of active sites facilitates high catalytic performance only conditionally, while the overall activity being highly dependent on the accessibility of the active sites to effective transport of the electrolyte, where contribution of surface morphology is crucial for product escape during gas evolution. © 2012 Elsevier Ltd.

Three differently detailed kinetic models for methanol synthesis are derived for experimental data measured over a ternary copper catalyst. Two global reactor models for reaction design, including a power law and a Langmuir-Hinshelwood-Hougen-Watson approach, are presented. In addition a microkinetic model is adapted to describe the whole experimental data and is used to discuss dynamical changes occurring during methanol synthesis. The first global model based on power law kinetics is very precisely in predicting the integral rates of methanol production. The power law requires the inclusion of a water inhibition term to be applicable over the whole range of experiments. A semi-empirical Langmuir-Hinshelwood-Hougen-Watson model, taken from the literature, gives essentially the same results, even upon extrapolation. The third model, a microkinetic model, was successfully fitted with only two variables and is in reasonable agreement with the experimental data. For all models a sensitivity analysis shows the influencing parameters on the methanol production rate. The valid microkinetic model, however, can give qualitative estimations of the structure sensitivity and dynamic behavior of methanol synthesis. The dynamic change of active sites and of site distribution of different copper low-index planes along the reactor length is given and the inhibiting role of water, indicated by the power law and microkinetic model, is analyzed. © 2012 Elsevier B.V.

The synthesis of bimetallic nanoparticles (NPs) with well-defined morphology and a size of <5 nm remains an ongoing challenge. Here, we developed a facile and efficient approach to the design of bimetallic nanostructures by the galvanic replacement reaction facilitated by high-intensity ultrasound (100 W, 20 kHz) at low temperatures. As a model system, Pt-Cu NPs deposited on nitrogen-doped carbon nanotubes (NCNTs) were synthesized and characterized by spectroscopic and microscopic techniques. Transmission electron microscopy (TEM) inspection shows that the mean diameter of Pt-Cu NPs can be as low as ≈2.8 nm, regardless of the much larger initial Cu particle size, and that a significant increase in particle number density by a factor of 35 had occurred during the replacement process. The concentration of the Pt precursor solution as well as of the size of the seed particles were found to control the size of the bimetallic NPs. Energy dispersive X-ray spectroscopy performed in the scanning TEM mode confirmed the alloyed nature of the Pt-Cu NPs. Electrochemical oxygen reduction measurements demonstrated that the resulting Pt-Cu/NCNT catalysts exhibit an approximately 2-fold enhancement in both mass- and area-related activities compared with a commercial Pt/C catalyst. © 2012 American Chemical Society.

A high-yielding exfoliation of graphene at high concentrations in aqueous solutions is critical for both fundamental study and future applications. Herein, we demonstrate the formation of stable aqueous dispersions of pristine graphene by using the surfactant sodium taurodeoxycholate under tip sonication at concentrations of up to 7.1 mg mL -1. TEM showed that about 8 % of the graphene flakes consisted of monolayers and 82 % of the flakes consisted of less than five layers. The dispersions were stable regardless of freezing (-20 °C) or heat treatment (80 °C) for 24 h. The concentration could be significantly improved to about 12 mg mL -1 by vacuum-evaporation of the dispersions at ambient temperature. The as-prepared graphene dispersions were readily cast into conductive films and were also processed to prepare Pt/graphene nanocomposites that were used as highly active electrocatalysts for the oxygen-reduction reaction. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Knowledge of the state of ionization and tautomerization of heteroaromatic cofactors when enzyme-bound is essential for formulating a detailed stepwise mechanism via proton transfers, the most commonly observed contribution to enzyme catalysis. In the bifunctional coenzyme, thiamin diphosphate (ThDP), both aromatic rings participate in catalysis, the thiazolium ring as an electrophilic covalent catalyst and the 4″-aminopyrimidine as acid-base catalyst involving its 1″,4″-iminopyrimidine tautomeric form. Two of four ionization and tautomeric states of ThDP are well characterized via circular dichroism spectral signatures on several ThDP superfamily members. Yet, the method is incapable of providing information about specific proton locations, which in principle may be accessible via NMR studies. To determine the precise ionization/tautomerization states of ThDP during various stages of the catalytic cycle, we report the first application of solid-state NMR spectroscopy to ThDP enzymes, whose large mass (160,000-250,000 Da) precludes solution NMR approaches. Three de novo synthesized analogues, [C2,C6″- 13C 2]ThDP, [C2- 13C]ThDP, and [N4″- 15N]ThDP used with three enzymes revealed that (a) binding to the enzymes activates both the 4″-aminopyrimidine (via pK a elevation) and the thiazolium rings (pK a suppression); (b) detection of a pre-decarboxylation intermediate analogue using [C2,C6″- 13C 2]ThDP, enables both confirmation of covalent bond formation and response in 4″-aminopyrimidine ring's tautomeric state to intermediate formation, supporting the mechanism we postulate; and (c) the chemical shift of bound [N4″- 15N]ThDP provides plausible models for the participation of the 1″,4″-iminopyrimidine tautomer in the mechanism. Unprecedented detail is achieved about proton positions on this bifunctional coenzyme on large enzymes in their active states. © 2011 American Chemical Society.

There is an increasing interest in replacing non-selective metal catalysts, currently used in low temperature fuel cells, with enzymes as catalysts. Specific oxidation of fuel and oxidant by enzymes as catalysts yields enzymatic fuel cells. If the catalysts can be immobilised at otherwise inert anode and cathode materials, this specificity of catalysis obviates the requirement for fuel cell casings and membranes permitting fuel cell configurations amenable to miniaturisation to be adopted. Such configurations have been proposed for application to niche areas of power generation: powering remotely located portable electronic devices, or implanted biomedical devices, for example. We focus in this review on recent efforts to improve electron transfer between the enzymes and electrodes, in the presence or absence of mediators, with most attention on research aimed at implantable or semi-implantable enzymatic fuel cells that harvest the body's own fuel, glucose, coupled to oxygen reduction, to provide power to biomedical devices. This ambitious goal is still at an early stage, with device power output and stability representing major challenges. A comparison of performance of enzymatic fuel cell electrodes and assembled fuel cells is attempted in this review, but is hampered in general by lack of availability of, and conformity to, standardised testing and reporting protocols for electrodes and cells. We therefore highlight reports that focus on this requirement. Ultimately, insight gained from enzymatic fuel cell research will lead to improved biomimetics of enzyme catalysts for fuel cell electrodes. These biomimetics will mimic enzyme catalytic sites and the structural flexibility of the protein assembly surrounding the catalytic site. © 2012 Elsevier Ltd.

After their discovery in the early 1990s, ordered mesoporous materials have become one of the most widely investigated classes of materials, and applications have been considered in many areas, in particular in catalysis. They have attracted attention because of their unique properties such as high surface areas, controllable compositions, crystallinity, thermal and chemical stability, tailored porosities, narrow pore size distributions, concave surface curvatures, surface functionalities, as well as the opportunities they offer for incorporation of catalytically active and selective species. This chapter is focused on the properties of ordered mesoporous solids that distinguish them from more conventional porous catalytic materials. Emphasis is placed on history, development, and methods of synthesis of ordered mesoporous materials. © 2012 Elsevier Inc..

High-temperature Fischer-Tropsch synthesis for the production of short-chain olefins over iron catalysts supported on multiwalled carbon nanotubes (CNTs) was investigated under industrially relevant conditions (340°C, 25bar, H 2/CO=1) to elucidate the influence of nitrogen and oxygen functionalization of the CNTs on the activity, selectivity, and long-term stability. Surface functionalization of the CNTs was achieved by means of a gas-phase treatment using nitric acid vapor at 200°C for oxygen functionalization (O-CNTs) and ammonia at 400°C for the subsequent nitrogen doping (N-CNTs). Ammonium iron citrate impregnation followed by calcination was applied for the deposition of iron nanoparticles with particle sizes below 9nm. Subsequent to reduction in pure H 2 at 380°C, the Fe/N-CNT and Fe/O-CNT catalysts were applied in Fischer-Tropsch synthesis, in which they showed comparable initial conversion values with an excellent olefin selectivity [S(C 3-C 6)>85%] and low chain growth probability (α≤0.5). TEM analysis of the used catalysts detected particle sizes of 23 and 26nm on O-CNTs and N-CNTs, respectively, and Fe 5C 2 was identified as the major phase by using XRD, with only traces of Fe 3O 4. After 50h time on stream under steady-state conditions, an almost twofold higher activity compared to the Fe/O-CNT catalysts had been maintained by the Fe/N-CNT catalysts, which are considered excellent Fischer-Tropsch catalysts for the production of short-chain olefins owing to their high activity, high selectivity to olefins, low chain growth probability, and superior long-term stability. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An industrially applicable cobalt-based catalyst was optimized for the production of multiwalled carbon nanotubes (CNTs) from ethene in a hot-wall reactor. A series of highly active Co-Mn-Al-Mg spinel-type oxides with systematically varied Co: Mn ratios was synthesized by precipitation and calcined at different temperatures. The addition of Mn drastically enhanced the catalytic activity of the Co nanoparticles resulting in an extraordinarily high CNTyield of up to 249 g CNT/gcat. All quaternary catalysts possessed an excellent selectivity towards the growth of CNTs. The detailed characterization of the obtained CNTs by electron microscopy, Raman spectroscopy and thermogravimetry demonstrated that a higher Mn content results in a narrower CNT diameter distribution, while the morphology of the CNTs and their oxidation resistance remains rather similar. The temperature- programmed reduction of the calcined precursors as well as in situ X-ray absorption spectroscopy investigations during the growth revealed that the remarkable promoting effect of the Mn is due to the presence of monovalent Mn (II) oxide in the working catalyst, which enhances the catalytic activity of the metallic Co nanoparticles by strong metal-oxide interactions. The observed correlations between the added Mn promoter and the catalytic performance are of high relevance for the production of CNTs on an industrial scale. © 2011 Elsevier Ltd. All rights reserved.

A new class of CeO2/Pt nanostructures containing highly porous carbide-derived carbon composites was obtained for the first time using a polymer precursor strategy and subsequent ceramization. The catalytic transition metal compounds were incorporated into polymeric polycarbosilane structures using an inverse microemulsion method in precisely tunable nanoscale particle sizes. Porous ceramic and carbon composites were obtained by pyrolysis and subsequent chlorination processes. The adsorption properties of nonoxidic ceramic intermediates can be adjusted by the pyrolysis temperatures from mainly microporous to meso- and macroporous materials, respectively. These pore structures remain during the chlorination process confirmed by comparative nitrogen physisorption and small-angle X-ray scattering investigations. The specific surface areas significantly increase up to 1774 m2/g after selective silicon removal. In comparison to unsupported CeO2/Pt nanoparticle structures, the particle sizes and dispersion of the active metal compounds of composite structures remain during pyrolysis and chlorination process studied by electron microscopy methods. Ceramic and carbonaceous composites show catalytic activity and stability in selective methane oxidation. In contrast to the SiC composites, the CDC materials promote the formation of carbon monoxide and hydrogen in reforming reactions at higher temperatures, a conversion pathway important for the generation of synthetic fuels. © 2010 American Chemical Society.

The use of nanostructured yolk-shell materials offers a way to discriminate support and particle-size effects for mechanistic studies in heterogeneous catalysis. Herein, gold yolk-shell materials have been synthesized and used as model catalysts for the investigation of support effects in CO oxidation. Carbon has been selected as catalytically inert support to study the intrinsic activity of the gold nanoparticles, and for comparison, zirconia has been used as oxidic support. Au, @C materials have been synthesized through nanocasting using two different nonporous-core@mesoporous-shell exotemplates: Au@SiO 2@ZrO2 and Au@SiO2@m-SiO2. The catalytic activity of Au, @C with a gold core of about 14nm has been evaluated and compared with Au, @ZrO2 of the same gold core size. The strong positive effect of metal oxide as support material on the activity of gold has been proved. Additionally, size effects were investigated using carbon as support to determine only the contribution of the nanoparticle size on the catalytic activity of gold. Therefore, Au, @C with a gold core of about 7nm was studied showing a less pronounced positive effect on the activity than the metal oxide support effect. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An in-depth understanding of the fundamental structure of catalysts during operation is indispensable for tailoring future efficient and selective catalysts. We report the evolution of the structure and oxidation state of ZrO2-supported Pd nanocatalysts (∼5 nm) during the in situ reduction of NO with H2 using X-ray absorption fine-structure spectroscopy and X-ray photoelectron spectroscopy. Prior to the onset of the reaction (≤120 °C), a NO-induced redispersion of our initial metallic Pd nanoparticles over the ZrO2 support was observed, and Pd δ+ species were detected. This process parallels the high production of N2O observed at the onset of the reaction (>120 °C), while at higher temperatures (≥150 °C) the selectivity shifts mainly toward N2 (∼80%). Concomitant with the onset of N 2 production, the Pd atoms aggregate again into large (6.5 nm) metallic Pd nanoparticles, which were found to constitute the active phase for the H2-reduction of NO. Throughout the entire reaction cycle, the formation and stabilization of PdOx was not detected. Our results highlight the importance of in situ reactivity studies to unravel the microscopic processes governing catalytic reactivity. © 2011 American Chemical Society.

p-Type Co3O4 nanostructured films are synthesized by a plasma-assisted process and tested in the photocatalytic production of H 2 from water/ethanol solutions under both near-UV and solar irradiation. It is demonstrated that the introduction of fluorine into p-type Co3O4 results in a remarkable performance improvement with respect to the corresponding undoped oxide, highlighting F-doped Co 3O4 films as highly promising systems for hydrogen generation. Notably, the obtained yields were among the best ever reported for similar semiconductor-based photocatalytic processes. © 2011 American Chemical Society.

Co-precipitation of Cu,Zn,(Al) precursor materials is the traditional way of synthesizing Cu/ZnO/(Al2O3) catalysts for industrial methanol synthesis. This process has been investigated by titration experiments of nitrate and formate solutions. It was found that the solidification of the single components proceeds sequentially in case of nitrates: Cu2+ is precipitated at pH 3 and Zn2+ (as well as Al3+) near pH 5. This behavior prevents a homogeneous distribution of all metal species in the initial precipitate upon gradual increase of pH and requires application of the constant pH micro-droplet method. This effect is less pronounced if formate instead of nitrate is used as counter ion. This can be explained by the strong modification of the hydrolysis chemistry of the metal ions due to the presence of formate anions, which act as ligands and buffer. A formate-derived Cu/ZnO/Al2O3 catalyst was more active in methanol synthesis compared to a nitrate-derived sample although the same crystallographic phases were present in the precursor after co-precipitation and ageing. The effect of precipitation temperature was studied for the binary CuZn nitrate model system. Increasing the temperature of co-precipitation above 50 °C leads to down-shift of the precipitation pH of Zn2+ by a full unit. Thus, in warm solutions more acidic conditions can be used for complete co-precipitation, while in cold solutions, some Zn2+ may remain dissolved in the mother liquor at the same precipitation pH. The higher limit of temperature is given by the tendency of the initial Cu precipitate towards formation of CuO by oxolation. On the basis of these considerations, the empirically determined optimal pH and temperature conditions of the industrially applied synthesis can be rationalized. © 2010 Elsevier B.V. All rights reserved.

High-temperature, stable core-shell catalysts for ammonia decomposition have been synthesized. The highly active catalysts, which were found to be also excellent model systems for fundamental studies, are based on α-Fe 2O 3 nanoparticles coated by porous silica shells. In a bottom-up approach, hematite nanoparticles were firstly obtained from the hydrothermal reaction of ferric chlorides, L-lysine, and water with adjustable average sizes of 35, 47, and 75nm. Secondly, particles of each size could be coated by a porous silica shell by means of the base-catalyzed hydrolysis of tetraethylorthosilicate (TEOS) with cetyltetramethylammonium bromide (CTABr) as porogen. After calcination, TEM, high-resolution scanning electron microscopy (HR-SEM), energy-dispersive X-ray (EDX), XRD, and nitrogen sorption studies confirmed the successful encapsulation of hematite nanoparticles inside porous silica shells with a thickness of 20nm, thereby leading to composites with surface areas of approximately 380 m 2g -1 and iron contents between 10.5 and 12.2wt%. The obtained catalysts were tested in ammonia decomposition. The influence of temperature, iron oxide core size, possible diffusion limitations, and dilution effects of the reagent gas stream with noble gases were studied. The catalysts are highly stable at 750°C with a space velocity of 120000 cm 3 g cat -1h -1 and maintained conversions of around 80% for the testing period time of 33 h. On the basis of the excellent stability under reaction conditions up to 800°C, the system was investigated by in situ XRD, in which body-centered iron was determined, in addition to FeN x, as the crystalline phase under reaction conditions above 650deg;C. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The efficient electron transfer between redox enzymes and electrode surfaces can be obtained by wiring redox enzymes using, for instance, polymer-bound redox relays as has been demonstrated as a basis for the design of amperometric biosensors, logic gates or sensor arrays and more general as a central aspect of "bioelectrochemistry". Related devices allow exploiting the unique catalytic properties of enzymes, among which photosynthetic enzymes are especially attractive due to the possibility to trigger the redox reactions upon irradiation with light. Photocatalytic properties such as the light-driven water splitting by photosystem 2 make them unique candidates for the development of semiartificial devices which convert light energy into stable chemical products, like hydrogen. This review summarizes recent concepts for the integration of photosystem 1 and photosystem 2 into bioelectrochemical devices with special focus on strategies for the design of electron transfer pathways between redox enzymes and conductive supports. © 2011 The Royal Society of Chemistry.

High-performance Cu/ZnO/(Al2O3) methanol synthesis catalysts are conventionally prepared by co-precipitation from nitrate solutions and subsequent thermal treatment. A new synthesis route is presented, which is based on similar preparation steps and leads to active catalysts, but avoids nitrate contaminated waste water. © 2011 The Royal Society of Chemistry.

Cyclic temperature-programmed reduction (TPR) and reoxidation (TPO) experiments can mimic the redox mechanism suggested by Mars and van Krevelen when using a hydrocarbon as reductant. The redox cycles enable fast probing of the activity and selectivity of multi-component oxide catalysts applied in the selective oxidation of short hydrocarbons. The technique was applied to quantitatively assess the redox properties of active bismuth molybdates and inactive bismuth tungstates (Bi2MxO3x+3, M = Mo, W), which are components of industrial acrolein synthesis catalysts. The specific reducibility of the supporting complex oxide Fe3Co 7Mo12O46 is found to be low due to its comparably high surface area. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Simple as that: A novel crystalline microporous titanosilicate (Ti-COE-4) with functionalized hydroxyl groups and medium micropore size (0.55nm) is successfully synthesized through dimethylsilylation and calcination. The synergism of hydroxyl groups with active Ti sites in Ti-COE-4 significantly improves its catalytic activities in oxidation reactions. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nanostructured MgH2/0.1TiH2 composite was synthesized directly from Mg and Ti metal by ball milling under an initial hydrogen pressure of 30 MPa. The synthesized composite shows interesting hydrogen storage properties. The desorption temperature is more than 100 °C lower compared to commercial MgH2 from TG-DSC measurements. After desorption, the composite sample absorbs hydrogen at 100 °C to a capacity of 4 mass% in 4 h and may even absorb hydrogen at 40 °C. The improved properties are due to the catalyst and nanostructure introduced during high pressure ball milling. From the PCI results at 269, 280, 289 and 301 °C, the enthalpy change and entropy change during the desorption can be determined according to the van't Hoff equation. The values for the MgH2/0.1TiH2 nano-composite system are 77.4 kJ mol-1 H2 and 137.5 J K-1 mol-1 H2, respectively. These values are in agreement with those obtained for a commercial MgH2 system measured under the same conditions. Nanostructure and catalyst may greatly improve the kinetics, but do not change the thermodynamics of the materials. © 2011, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

CO adsorption at 1 MPa on Cu-Zn stearate colloids and supported Cu catalysts was studied in situ by attenuated total reflection infrared (ATR-IR) spectroscopy. Subsequent to thorough reduction by H2, the IR band at 2110-2070 cm-1 due to linearly adsorbed CO on clean metallic Cu was always observed initially on all Cu catalysts. During the exposure of Zn-containing samples to CO at high pressure, a new IR band at ca. 1975 cm -1 appeared in addition and increased in intensity even at room temperature. The detailed analysis of the IR spectra showed that the new IR band at ca. 1975 cm-1 was not related to coadsorbed carbonate/formate- like species, but to the content of Zn in the samples. This IR band was found to be more stable than that at 2110-2070 cm-1 during purging with inert gas. It disappeared quickly in synthetic air, pointing to a strongly reduced state of the Zn-containing Cu catalysts achieved during high-pressure CO exposure. It is suggested that CO can reduce ZnO to Zn in the presence of Cu, resulting in the formation of a CuZnx surface alloy. As the CO species with the characteristic IR band at ca. 1975 cm-1 binds more strongly to this CuZnx alloy than the linearly adsorbed CO to pure Cu, it is suggested to be adsorbed on a bridge site. © 2011 American Chemical Society.

CO oxidation was studied with a model catalyst containing Au and TiO x nanoaggregates confined in a siliceous MCM-48 host. With this material, which has a particular small ratio between the TiO x and Au components, activities well comparable to those of unconfined Au/TiO 2 catalysts were obtained in particular when a thermal activation in inert gas at temperatures between 523 and 673 K was applied. When the subsequent catalytic tests were performed in a feed containing ca. 20 ppm H 2O, strong deactivation phenomena were observed which could be reverted by repeated thermal treatment and are most likely caused by carbonate deposition. This deactivation was strongly attenuated when the water content of the feed was decreased to ca. 6 ppm, which suggests that water plays an important role in the formation of the poisoning species. With unconfined Au/TiO 2 catalysts, a promoting role of water on the formation of catalyst poison was observed as well, but to a much lower extent. The effect may therefore have escaped undetected so far as a contribution to the well-known catalyst deactivation by carbonate species. © 2011 Springer Science+Business Media, LLC.

Rhodium Drive: Carbon nanotube-supported rhodium sulfide electrocatalysts are prepared by sequential chemical vapor deposition of iron, controlled vapor phase polymerization of thiophene, and finally impregnation of the rhodium precursor and pyrolysis. The electrocatalysts are applied in the oxygen reduction reaction under HCl electrolysis conditions. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A high surface area Co3O4 - SiO2 nanocomposite catalyst has been prepared by use of activated carbon as template. The Co3O4 - SiO2 composite, the surface of which is rich in silica and Co(II) species compared with normal Co 3O4, exhibited very high activity for CO oxidation even at a temperature as low as '76 °C. A rather unusual temperature-dependent activity curve, with the lowest conversion at about 80 °C, was observed with a normal feed gas (H2O content 3 ppm). The U-shape of the activity curve indicates a negative apparent activation energy over a certain temperature range, which has rarely been observed for the heterogeneously catalyzed oxidation of CO. Careful investigation of the catalytic behavior of Co 3O4 - SiO2 catalyst led to the conclusion that adsorption of H2O molecules on the surface of the catalyst caused the unusual behavior. This conclusion was supported by in situ diffuse reflectance Fourier transform infrared (DRIFT) spectroscopic experiments under both normal and dry conditions. © 2011 American Chemical Society.

Au, ZrO2 yolk-shell catalysts were found to exhibit a surprisingly high activity in CO oxidation even though the gold particle size is about 15 nm. A further enhancement of the activity has been achieved by simply doping these materials with small amounts of TiO2 during synthesis. A comparison of the standard Au, @ZrO2 yolk-shell catalysts with the novel TiO2-doped Au/Ti, @ZrO2 shows significant activity enhancement, even though small amounts of TiO2 are present. © 2011 The Royal Society of Chemistry.

A straight-forward method for the synthesis of metal-free catalysts for oxygen reduction by thermal treatment of a mixture of poly(3,5-pyridine) with carbon black in helium is reported. The catalyst was characterized by X-ray diffraction and photoelectron spectroscopy, cyclic voltammetry and rotating disk electrode measurements. The new catalyst exhibited remarkable activity similar to Pt-based catalysts in alkaline media. © 2011 Elsevier B.V. All Rights Reserved.

Scanning electrochemical microscopy in the redox competition mode (RC-SECM) is proposed as an useful technique for local investigation of the electrocatalytic activity of different catalysts towards the oxygen reduction reaction (ORR) with simultaneous detection of the produced undesirable intermediate hydrogen peroxide. We have used cobalt porphyrin dispersed in a multiwalled carbon nanotubes (MWCNTs) matrix as a model electrocatalyst for the predominant two-electron reduction of oxygen to hydrogen peroxide. Furthermore, Prussian Blue or horseradish peroxidase were used as catalysts for the further reduction of hydrogen peroxide to water. The properties of each component of the film were examined along with their potential interactions with the other components. As a result an efficient electrocatalyst for oxygen reduction at physiological pH could be obtained. ©The Electrochemical Society.

A novel continuous method for the preparation of a ternary Cu/ZnO/Al 2O 3 catalyst based on a cascade of micromixers and a tubular aging reactor is presented as a promising alternative route to the conventional batch process. Its application, in combination with immediate spray drying, enables monitoring of the formation of the final precursor by exchange reactions between initially separated phases during the aging step. These exchange reactions were successfully simulated by consecutive precipitation by using micromixers in series as analytical tool. After 60min of continuous aging, calcination, and reduction, a catalyst is produced that exhibits an almost equal mass-related activity in methanol synthesis compared to a commercial catalyst and an area-related activity that is about 50% higher. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Yolk-shell catalysts have attracted interest in both academia and industry, since they combine high-temperature stability with a reduced complexity for kinetic and mechanistic investigations. This contribution presents a possibility to adjust the size of an active gold core inside a porous zirconia shell via an ex-post-modification approach. © The Royal Society of Chemistry 2010.

The catalytic properties of nanocrystalline HZSM-5 catalysts with high Si/Al molar ratio (ca. 65) were investigated in the gas phase dehydration of aqueous glycerol. Compared with bulk HZSM-5, the small-sized catalyst exhibits greatly enhanced catalytic performance in glycerol dehydration even with very high GHSV (=1438 h -1). Catalysts with different Si/Al ratios were studied, but it is difficult to separate the influence of Si/Al ratio from that of particle size. However, by varying the proton exchange degree for one mother batch of zeolite, a series of H xNa 1-xZSM-5 catalysts with same particle size and different Brønsted acid site densities was prepared. The catalytic results for this series of samples show that high density of Brønsted acid sites favors the production of acrolein. Based on these results, small-sized HZSM-5 with high aluminum content appears to be most promising for gas phase dehydration of glycerol. © 2009 Elsevier Inc. All rights reserved.

An extensive set of characterization methods is required to study the processes occurring during the evolution of the initially amorphous precursor towards the complex Cu/ZnO/Al 2O 3 system. A novel preparation method was therefore developed that provides the possibility of a systematic study of all components in the different stages of the precipitation of the ternary catalyst. As a result, a continuously operating synthesis route was established as an alternative to the industrially applied process. © 2010 Elsevier B.V. All rights reserved.

We present the study on the catalytic performance of gold particles supported on spinel type MgFe2O4 nanocrystals (Au/MgFe2O4) which exhibit high activity for low temperature CO oxidation. Using XRD, TEM, XPS and CO titration techniques, we investigated the effect of the pretreatment atmosphere on the structure and catalytic properties of the Au/MgFe2O4 catalyst in CO oxidation. TEM, XPS and XRD showed that the pretreatment atmosphere had a negligible effect on the particle size distribution, chemical states of the gold, and the structure of the support. Among the various pretreated catalysts, O2-Au/MgFe2O4 exhibits superior activity, indicating that pretreatment in oxidative atmosphere induced the high capability of the catalyst to activate CO and supply active oxygen for CO oxidation as confirmed by CO titration experiments. © 2010 Elsevier B.V. All rights reserved.

Nickel hydride with a diphosphinite-based ligand catalyzes the highly efficient reduction of CO2 with catecholborane, and the hydrolysis of the resulting methoxyboryl species produces CH3OH in good yield. The mechanism involves a nickel formate, formaldehyde, and a nickel methoxide as different reduced stages for CO2. The reaction may also be catalyzed by an air-stable nickel formate. © 2010 American Chemical Society.

The oxygen storage capacity (OSC) and its correlation with the activity for the CO oxidation reaction and the reducibility of the support material were investigated for four different metal oxide-supported Au catalysts with similar Au loading and Au particle sizes (Au/Al2O3, Au/TiO 2, Au/ZnO, Au/ZrO2), which were prepared by deposition of pre-formed Au colloids. Temporal Analysis of Products (TAP) reactor measurements show that the OSC and the activity for CO oxidation, measured under identical conditions, differ significantly for these catalysts and are correlated with each other and with the reducibility of the respective support material, pointing to a distinct support effect and a direct participation of the support in the reaction. Activity measurements performed under ambient conditions show a similar trend of the activity as the TAP reactor measurements, supporting that the conclusions drawn from the TAP reactor measurements are valid also under continuous reaction conditions. Moreover, the rapid formation and accumulation of carbon-containing surface species during reaction is demonstrated, which can severely reduce the activity for CO oxidation. Implications of these results on the CO oxidation mechanism over metal oxide-supported catalysts are discussed. © 2010 Elsevier Inc. All rights reserved.

Platinum based binary and ternary catalysts were prepared by thermal decomposition onto a titanium mesh and were evaluated for the anodic oxidation of methanol. The binary Pt:Ru catalyst with a composition of 1:1 gave the highest performance for methanol oxidation at 80° C. The effect of temperature and time for thermal decomposition was optimized with respect to methanol oxidation, and the catalysts were characterized by cyclic voltammetry, linear sweep voltammetry, scanning electron microscopy, X-ray diffraction studies, and X-ray photoelectron spectroscopy. The best catalyst was evaluated in a single fuel cell, and the effect of methanol concentration, temperature, and oxygen/air flow was studied. The mesh-based fuel cell, operating at 80°C with 1 mol dm 3 methanol, gave maximum power densities of 38 mWcm -2 and 22 mWcm -2 with 1 bar (gauge) oxygen and air, respectively. © 2010 by ASME.

Exciting new opportunities are emerging in the field of catalysis based on nanotechnology approaches. A new understanding and mastery of catalysis could have broad societal impacts, since about 80% of the processes in the chemical industry depend on catalysts to work efficiently. Efforts in surface science have led to the discovery of new heterogeneous catalysts, however, until recently the only way to develop new or improved catalysts was by empirical testing in trial-and-error experiments. This time-consuming and costly procedure is now rapidly being replaced by rational design methods that utilize fundamental knowledge of catalysts at the nanoscale. The advent of nanoscience and nanotechnology is providing the ability to create controlled structures and geometries to investigate and optimize a broad range of catalytic processes. As a result, researchers are obtaining fundamental insight into key features that influence the activity, selectivity, and lifetime of nanocatalysts. This review article examines several new findings as well as current challenges in the field of nanoparticle based catalysis, including the role played by the particle structure and morphology (size and shape), its chemical composition and oxidation state, and the effect of the cluster support. © 2010 Elsevier B.V. All rights reserved.

Uniform and highly dispersed γ-Fe 2O 3 nanoparticles with a diameter of ∼6 nm supported on CMK-5 carbons and C/SBA-15 composites were prepared via simple impregnation and thermal treatment. The nanostructures of these materials were characterized by XRD, Mössbauer spectroscopy, XPS, SEM, TEM, and nitrogen sorption. Due to the confinement effect of the mesoporous ordered matrices, γ-Fe 2O 3 nanoparticles were fully immobilized within the channels of the supports. Even at high Fe-loadings (up to about 12 wt %) on CMK-5 carbon no iron species were detected on the external surface of the carbon support by XPS analysis and electron microscopy. Fe 2O 3/CMK-5 showed the highest ammonia decomposition activity of all previously described Fe-based catalysts in this reaction. Complete ammonia decomposition was achieved at 700 °C and space velocities as high as 60 000 cm 3 g cat -1 h -1. At a space velocity of 7500 cm 3 g cat -1 h -1, complete ammonia conversion was maintained at 600 °C for 20 h. After the reaction, the immobilized γ-Fe 2O 3 nanoparticles were found to be converted to much smaller nanoparticles (γ-Fe 2O 3 and a small fraction of nitride), which were still embedded within the carbon matrix. The Fe 2O 3/CMK-5 catalyst is much more active than the benchmark NiO/Al 2O 3 catalyst at high space velocity, due to its highly developed mesoporosity. γ-Fe 2O 3 nanoparticles supported on carbon-silica composites are structurally much more stable over extended periods of time but less active than those supported on carbon. TEM observation reveals that iron-based nanoparticles penetrate through the carbon layer and then are anchored on the silica walls, thus preventing them from moving and sintering. In this way, the stability of the carbon-silica catalyst is improved. Comparison with the silica supported iron oxide catalyst reveals that the presence of a thin layer of carbon is essential for increased catalytic activity. © 2010 American Chemical Society.

Highly loaded copper catalysts supported on alumina are synthesized applying the cyclic two-step CVD of the precursor copper(II)diethylamino-2- propoxide in a fluidized-bed reactor. Copper/zinc oxide/alumina composites are synthesized by either the CVD of the precursor bis[bis (trimethylsilyl) amido]zinc on Cu/Al2O3, or the CVD of the Cu precursor on Zn-pretreated alumina, impregnating with diethyl zinc in addition. The composites are extensively characterized by atomic absorption spectroscopy (AAS), elemental analysis (EA), mass spectrometry (MS), N2 physisorption, N2O reactive frontal chromatography (RFC), and X-ray diffraction (XRD). The Cu and ZnO nanoparticles originating from the efficient two-step procedure, consisting of adsorption and subsequent decomposition of the adsorbed species in two separated steps, are highly dispersed, X-ray amorphous, and, in the case of the Cu-containing catalysts, have high specific Cu surface areas. The catalytic activities are determined both in methanol synthesis, to judge the contact between the deposited Cu and ZnO nanoparticles, and in the steam reforming of methanol (SRM) to probe the stability of the Cu particles. The turn-over frequencies (TOF) in methanol synthesis of these Cu/ZnO/Al 2O3 catalysts are higher than that of a commercial ternary catalyst. The varied sequence of the CVD of Cu and ZnO on alumina leads to catalysts with similar activities in the case of similar specific Cu areas. © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Carbon nanotube (CNT) supported sulfided Rh catalysts were prepared applying three different routes: deposition-precipitation (DP), grafting of colloidal Rh nanoparticles, and polythiophene-assisted synthesis. The catalysts (1.4-1.8 wt%) prepared by DP were synthesized on CNTs from RhCl3 using hydrogen peroxide and subsequent exposure to on-line generated H 2S followed by heat treatment. The Rh particles were found to be highly dispersed on the CNT surface. Alternatively, RhSx/Rh nanoparticles with four different loadings (4.3-21.9 wt%) grafted on carbon nanotubes were prepared through a functionalization of CNTs with short chain thiols and subsequent binding of colloidal Rh nanoparticles onto the thiolated CNTs. All steps of the synthesis were monitored by XPS. Finally, polythiophene/CNT composites were prepared and employed in the preparation of Rh17S15/Rh nanoparticles supported on CNTs. The CNTs with the highest polythiophene loading yielded the highest amount of Rh 17S15 after Rh deposition and thermal treatment. The activity and stability of the prepared catalysts were studied towards the oxygen reduction reaction. © 2010 Elsevier B.V. All rights reserved.

Composites consisting of multi-walled carbon nanotubes (MWCNTs) and iron-nitrogen containing compounds as catalysts for the electroreduction of oxygen in acidic media were directly prepared on a glassy carbon (GC) electrode in a bottom-up synthesis. In a first step, MWCNTs were drop-coated in form of an ink onto the electrode. Afterwards the nanotubes were modified with catalytically active films of iron porphyrin (FeTMPP-Cl) or iron phenanthroline (Fe(phen)3) through a pulsed potential deposition technique. Finally the prepared electrodes were heat-treated in an inert gas atmosphere. By employing cyclic voltammetry and rotating disc electrode measurements it is shown that the activity for the oxygen reduction reaction (ORR) at such composites increases progressively with every applied synthesis step showing the possibility for direct synthesis of a catalyst on an electrode. The activities of FeTMPP-Cl/MWCNT and Fe(phen)3/MWCNT composites prepared by this technique are higher than that of similar electrocatalysts prepared by wet impregnation and heat treatment. The presented approach opens possibilities for systematic tuning of electrode structures, for example by stepwise build-up of gas diffusion electrodes. © 2009 Elsevier Ltd.

Cellulose is a renewable and widely available feedstock. It is a biopolymer that is typically found in wood, straw, grass, municipal solid waste, and crop residues. Its use as raw material for biofuel production opens up the possibility of sustainable biorefinery schemes that do not compete with food supply. Tapping into this feedstock for the production of biofuels and chemicals requires-as the first-step-its depolymerization or its hydrolysis into intermediates that are more susceptible to chemical and/or biological transformations. We have shown earlier that solid acids selectively catalyze the depolymerization of cellulose solubilized in 1-butyl-3-methylimidazolium chloride (BMIMCl) at 100°C. Here, we address the factors responsible for the control of this reaction. Both cellulose and solid acid catalysts have distinct and important roles in the process. Describing the depolymerization of cellulose by the equivalent number of scissions occurring in the cellulosic chains allows a direct correlation between the product yields and the extent of the polymer breakdown. The effect of the acid strength on the depolymerization of cellulose is discussed in detail. Practical aspects of the reaction, concerning the homogeneous nature of the catalysis in spite of the use of a solid acid catalyst, are thoroughly addressed. The effect of impurities present in the imidazolium-based ionic liquids on the reaction performance, the suitability of different ionic liquids as solvents, and the recyclability of Amberlyst 15DRY and BMIMCl are also presented. © 2010 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A novel electrochemical method to prepare platinum shells around carbon-supported metal nanoparticles (Ru and Au) by pulsed electrodeposition from solutions containing Pt ions is presented. Shell formation is confirmed by characteristic changes in the cyclic voltammograms, and is further evidenced by monitoring particle growth by transmission electron microscopy as well as by energy-dispersive analysis of X rays (EDX). Scanning electrochemical microscopy and EDX measurements indicate a selective Pt deposition on the metal/carbon catalyst, but not on the glassy carbon substrate. The thus prepared carbon-supported core-shell nanoparticles are investigated with regard to their activity in electrocatalytic oxygen reduction, which demonstrates the applicability of these materials in electrocatalysis or sensors. © 2010 Wiley-VCH Verlag GmbH& Co. KGaA, Weinheim.

The structure, size, and shape of γ-Al2O 3-supported Pt nanoparticles (NPs) synthesized by inverse micelle encapsulation have been resolved via a synergistic combination of imaging and spectroscopic tools. It is shown that this synthesis method leads to 3D NP shapes even for subnanometer clusters, in contrast to the raft-like structures obtained for the same systems via traditional deposition-precipitation methods. Furthermore, a high degree of atomic ordering is observed for the micellar NPs in H2 atmosphere at all sizes studied, possibly due to H-induced surface reconstruction in these high surface area clusters. Our findings demonstrate that the influence of NP/support interactions on NP structure can be diminished in favor of NP/adsorbate interactions when NP catalysts are prepared by micelle encapsulation methods. © 2010 American Chemical Society.

Cross-metathesis can be used as a versatile tool to reversibly modify support materials with molecules bearing different functionalities. Two approaches, applying cross-metathesis either inside the pore system of SBA-15 as support material or in the liquid-phase prior to immobilization on the support, have been compared. Special attention is focussed on pitfalls and limitations of surface modifications inside the pore system of support materials and on strategies to overcome these challenges. The optimized immobilization procedure was successfully transferred to the reversible immobilization of a molecular catalyst. © 2010 Elsevier Inc. All rights reserved.

Rhodium-rhodium sulfide nanoparticles supported on multi-walled carbon nanotubes (CNTs) were synthesized via a multi-step colloid route. The CNTs were first exposed to nitric acid to generate oxygen-containing functional groups, and then treated with thionyl chloride to generate acyl chloride groups. The grafting of thiol groups was subsequently carried out by reaction with 4-aminothiophenol. Colloidal rhodium nanoparticles were synthesized using rhodium chloride as metal source, sodium citrate as stabilizer, and sodium borohydride as reducing agent. The immobilization of the generated colloidal rhodium nanoparticles was achieved by adding the thiolated CNTs to the colloidal suspension. All these steps were monitored by X-ray photoelectron spectroscopy, which disclosed the presence of rhodium sulfide, whereas metallic rhodium was detected by X-ray diffraction, suggesting that the nanoparticles probably consist of a metallic Rh core covered by a sulfide layer. Scanning and transmission electron microscopy studies showed that the diameter of the catalyst particles was about 7 nm even at high Rh loadings. Rotating disc electrode measurements and cyclic voltammetry were employed to test the electrocatalytic activity in the oxygen reduction reaction in hydrochloric acid. Among all the synthesized catalysts with different rhodium loadings (4.3-21.9%), the 16.1% rhodium catalyst was found to be the most active catalyst. In comparison to the commercial E-TEK Pt/C catalyst, the 16.1% catalyst displayed a higher electrochemical stability in the highly corrosive electrolyte, as determined by stability tests with frequent current interruptions. © 2010 The Royal Society of Chemistry.

Pt-Ag nanoparticles were prepared on a glassy carbon (GC) surface by pulsed electrodeposition and tested using cyclic voltammetry and scanning electrochemical microscopy (SECM) with respect to their possible use as catalyst material for oxygen reduction in 400 mM HCl solution. For comparison, a Pt catalyst was investigated under similar conditions. The redox competition mode of scanning electrochemical microscopy (RC-SECM) was adapted to the specific conditions caused by the presence of Cl ions and used to visualize the local catalytic activity of the Pt-Ag deposits. Similarly prepared Pt deposits were shown to dissolve underneath the SECM tip. Pt-Ag composites showed improved long-term stability toward oxygen reduction as compared with Pt even under multiple switching off to open-circuit potential in 400 mM HCl. © 2010 American Chemical Society.

Despite the advances in high throughput experimentation in recent years the synthesis of realistic catalyst libraries especially gradient catalyst libraries remains as a challenge in material science. Recently, we have developed a method for the synthesis of gradient catalyst libraries consisting of nanoparticles supported on high surface area porous substrates. Chemical vapor deposition (CVD) was employed as a gas-phase method for the synthesis. The method made use of the lateral concentration profile of the precursor-loaded carrier gas stream during CVD, resulting in concentration profile of the deposits on porous substrates. In this report, high surface area materials of both powders (e.g., silica) and bulk composites (e.g., hierarchical carbon structures) were successfully employed as substrates for the deposition of single metal or bimetallic catalyst libraries. The synthesis was achieved by controlling the flow behavior of the effluent precursor stream. The resulting effusion cone led to a radial deposition gradient on the substrate. Different from thin film-type model catalyst libraries, the obtained catalysts can be tested under realistic reaction conditions. Methanol oxidation was studied as a test reaction using scanning mass spectrometry. Copyright © 2010 American Scientific Publishers.

Tailoring the chemical reactivity of nanomaterials at the atomic level is one of the most important challenges in catalysis research. In order to achieve this elusive goal, fundamental understanding of the geometric and electronic structure of these complex systems at the atomic level must be obtained. This article reports the influence of the nanoparticle shape on the reactivity of Pt nanocatalysts supported on γ-Al2O3. Nanoparticles with analogous average size distributions (∼0.8-1 nm), but with different shapes, synthesized by inverse micelle encapsulation, were found to display distinct reactivities for the oxidation of 2-propanol. A correlation between the number of undercoordinated atoms at the nanoparticle surface and the onset temperature for 2-propanol oxidation was observed, demonstrating that catalytic properties can be controlled through shape-selective synthesis. © 2010 American Chemical Society.

The direct low-temperature oxidation of methane to methanol is demonstrated on a highly active homogeneous molecular catalyst system and on heterogeneous molecular catalysts based on polymeric materials possessing ligand motifs within the material structure. The N-(2-methylpropyl)-4,5-diazacarbazolyl-dichloro-platinum(II) complex reaches significantly higher activity compared to the well-known Periana system and allows first conclusions on electronic and structural requirements for high catalytic activity in this reaction. Interestingly, comparable activities could be achieved utilizing a platinum modified poly(benzimidazole) material, which demonstrates for the first time a solid catalyst with superior activity compared to the Periana system. Although the material shows platinum leaching, improved activity and altered electronic properties, compared to the conventional Periana system, support the proposed conclusions on structure-activity relationships. In comparison, platinum modified triazine-based catalysts show lower catalytic activity, but rather stable platinum coordination even after several catalytic cycles. Based on these systems, further development of improved solid catalysts for the direct low-temperature oxidation of methane to methanol is feasible. © 2010 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

(Figure Presented) The shape of gold: The title catalyst has been prepared through a colloidal deposition method. Scanning transmission electron microscopy studies confirmed that for the catalyst, gold clusters with a bilayer structure and a diameter of about 0.5 nm are not mandatory to achieve the high activity (see image). © 2010 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The formation of methane over unpromoted and potassium-promoted bulk iron catalysts applied in Fischer-Tropsch synthesis (FTS) was studied by dosing carbon monoxide pulses in hydrogen. A bulk metallic iron catalyst was obtained by H2 reduction, and cementite (Fe3C)-containing but oxygen-free iron was prepared by exposure to methane. The pulse experiments yielded mainly CH4 as well as small amounts of ethane and propane. The potassium-promoted samples reached higher degrees of CO conversion and lower CH4 selectivities. The Fe3C-containing catalysts were found to be more selective towards ethane and propane than reduced ones indicating that Fe3C is more active in FTS than metallic iron. The pulse experiments resulted in different signal shapes of the CH4 response curves reflecting the influence of the potassium promoter. The presence of potassium influenced the formation of CH4 by blocking the fast formation channel and by establishing a new and slower reaction pathway, whereas the addition of potassium did not change the reaction pathway towards higher hydrocarbons. Therefore, the decreasing CH4 formation rate contributes to the decreasing CH4 selectivity with increasing potassium content found under high-pressure steady-state conditions. Pressure variation experiments at steady state revealed that the kinetic results obtained during the pulse experiments were reproduced at 1 bar. Gradual continuous changes in the product distribution were observed with increasing pressure allowing extrapolating the concepts obtained from experiments at atmospheric pressure to industrial high-pressure FTS conditions. © 2010 Elsevier Inc. All rights reserved.

In this study, we provide a simple and reproducible method for the preparation of highly active and recyclable colloidal acid catalysts. First, 16-heptadecenoic acid-functionalized magnetite nanoparticles were encapsulated in monodisperse cross-linked polymer spheres. This was achieved by emulsion copolymerization technique in an aqueous phase of styrene and divinylbenzene (DVB). Different ratios of styrene and DVB were used to tune the structural stability and surface morphology of the composites. With increase in DVB content, the surfaces of the colloidal composites become increasingly rougher. The obtained colloids were functionalized with sulfonic acid groups to obtain magnetically recyclable catalysts with H+ contents in the range of 2.2-2.5 mmol g-1 and surface areas of 45-120 m2 g -1. For the condensation reaction of benzaldehyde and ethylene glycol, magnetic acid catalyst prepared only from DVB precursor was found to be active and with high selectivity and long-term stability. © 2010 American Chemical Society.

The understanding of reaction intermediates in heterogeneous catalysis has important implications for the design of novel catalysts. We investigate the adsorption of CO2 on oxygen precovered Ag(100) at low temperature (17 K) by scanning tunneling microscopy and inelastic electron tunneling manipulation at 5 K. On the terraces, the adsorption leads to O-Ag-CO 2-Ag-O compounds with reduced binding of the oxygen to the surface as compared to the separately adsorbed molecules. The compound can be either dissociated into a bistable O-Ag-CO2 compound at 1.6 V, dissociated into its constituents at 2.2 V, or reacted at 6.5 V into a species, which we tentatively attribute to CO3. The thus obtained carbon trioxide or carbonate is an intriguing reaction intermediate, because it is not stable in the gas phase. Our detailed study of coadsorbed species outlines a possibility to investigate precursors of reactions that involve the substrate atoms. © 2010 American Chemical Society.

The gold-zirconia yolk-shell system is an interesting catalyst for CO oxidation. The size distribution of the gold nanoparticles is very narrow, and they are well separated from each other also after treatment at high temperature, which is due to their encapsulation in crystalline zirconia hollow spheres. Because this allows thermal and chemical treatment without affecting the size distribution, different defect structures of the gold nanoparticles can be induced, and the effect on catalytic activity can be investigated. Line profile analysis of the powder diffraction data based on the whole powder pattern modeling approach was used to determine the domain size distribution and lattice defects present in this two-phase system. The influence of different diffractometer setups on the results of the line profile analysis was also investigated. Variation of the chemical and thermal treatment procedures allowed altering the microstructure of the system. The resulting catalysts showed substantial variation in the activity for CO oxidation. Lower dislocation densities and less stacking faults result in decreased catalytic activity. These contributions to activity could be studied without any superimposed size effect due to the constant gold particle sizes. © 2010 American Chemical Society.

Pt-Ag nanoparticle co-deposits with different Pt-Ag ratios were prepared on a glassy carbon (GC) surface by pulsed electrodeposition and investigated for their catalytic activity in electrocatalytic oxygen reduction by using cyclic voltammetry (CV), rotating disc electrode (RDE) and scanning electrochemical microscopy (SECM) in 0.1 M phosphate buffer (pH 7.0). The atomic composition of the Pt-Ag co-deposits was studied by means of energy-dispersive X-ray analysis (EDAX). In combination with X-ray diffraction (XRD), the presence of partly alloyed Pt and Ag on the GC surface was confirmed. Scanning electron microscopy (SEM) images indicate that the prepared Pt-Ag catalyst particles are homogenously dispersed over the GC surface. Their size and morphology depend on their composition. The electrocatalytic activity of Pt-Ag deposits with high Pt content was the highest, exceeding even that of electrodeposited Pt as evaluated by quantitative RDE analysis. The redox competition mode of scanning electrochemical microscopy (RC-SECM) was successfully used to visualize the local catalytic activity of the deposited Pt-Ag particles. Semi-quantitative assessment of the SECM results confirmed the same order of activity of the different catalysts as the RDE investigations. © 2009 Wlley-VCH Verlag GmbH & Co. KGaA,.

Low loading sulfided rhodium catalysts supported on carbon nanotubes (CNTs) were prepared from RhCl3 by deposition-precipitation using hydrogen peroxide, followed by an exposure to hydrogen sulfide and an additional thermal treatment in the range from 400 °C to 900 °C. Hydrogen sulfide was generated online from hydrogen and sulfur vapor over molybdenum disulfide as catalyst. By elemental analysis, the Rh loading of the prepared catalysts was found to be 1.4-1.8 wt%. Morphology and composition of the resulting catalysts were characterized by X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM), and X-ray photoelectron spectroscopy (XPS). Nanoparticles were found to be highly dispersed on the CNTs with an average diameter as small as 1.0 nm determined by TEM. Sintering occurred during heat treatments at 650 °C and 900 °C in helium, as evidenced by XRD, TEM, and XPS. The treatment with hydrogen sulfide significantly enhanced the activity of the supported rhodium catalysts for the oxygen reduction reaction (ORR) in hydrochloric acid, as determined by rotating disc electrode measurements. The sulfided catalyst annealed at 650 °C with a particle size of about 2.5 ± 1.0 nm showed the best performance for the ORR, which is discussed based on the presence of a more stable rhodium sulfide layer on the metallic rhodium particles. © 2009.

A synthesis route leading to Au/TiO2 clusters encaged in the three-dimensional channel system of siliceous MCM-48 was thoroughly studied to ensure reproducibility. Intermediate and final products were characterized by XRD, nitrogen physisorption, TEM, XPS and EXAFS. Via impregnation of MCM-48 with titanylacetylacetonate and subsequent deposition-precipitation using HAuCl4, ionic gold was introduced into the matrix, but a minority of the gold ended up in large metal particles on the external MCM-48 surface in the (freeze-dried) samples. The ionic gold underwent gradual autoreduction at room temperature in Ar even under dark conditions, but at 273 K, it may be kept ionic for months. The catalysts exhibited 50% CO conversion between 262 and 282 K, with good reproducibility. In addition, they achieved significant CO conversion with very low activation energy already at temperatures around 220 K; this low-temperature activity was less reproducible. Porosity analysis showed that the pore system was significantly perturbed after the Au introduction step without, however, precluding accessibility of the pore system. Therefore, further modification of the synthesis aiming at the conservation of the pore system may still bear promise for improvement. © 2008 Elsevier Inc. All rights reserved.

Palladium catalysts were synthesized in a highly controlled chemical vapor deposition process, giving narrowly distributed Pd nanoparticles with median sizes ranging from 1.3 to 5 nm on a SiO2 or TiO2 support. Unsupported Pd nanoparticles with median sizes between 3 and 9 nm were also generated by spark discharge. The influence of Pd particle size and support on the hydrogenation of ethene to ethane was investigated in a fixed-bed flow reactor at atmospheric pressure. The TOF was found to peak at 3 to 4 nm with a weak dependence on the support material. Metal support interactions were generally weak, indicated by closely matching activation energies of 20 kJ mol-1 for unsupported Pd, and 28 kJ mol-1 for titania and silica supported catalysts. Peak TOF values varied systematically with H2 partial pressure, indicating a pronounced volume effect of the Pd particles on the reactivity. © 2009 Elsevier Inc. All rights reserved.

Zinc oxide has a variety of applications in catalysis both as support and as active phase for hydrogenation or dehydrogenation reactions. This review provides an overview of the surface chemistry of ZnO nanoparticles concerning the interaction with small molecules such as CO, CO2, H2, H2O, and CH3OH, which are relevant for the catalytic synthesis of methanol and the water gas shift reaction. These interactions were studied by combining surface-sensitive methods such as infrared spectroscopy, temperature-programmed desorption, and adsorption calorimetry. A thorough understanding of the processes occurring on the different exposed facets of the ZnO particles in an atmosphere of reactive gases was achieved based on the comparison with results obtained in ultra-high vacuum with single-crystalline surfaces, i.e. under well-defined conditions, and by using first-principles calculations. © 2009 Elsevier B.V. All rights reserved.

The interaction of carbon monoxide and oxygen with gold particles supported on zinc oxide, alumina, and titania was investigated by microcalorimetry. Multiple processes were detected during CO adsorption, including adsorption of CO on the gold particles and support, oxidation of CO, and formation of carbonates. The rate of O2 adsorption was much slower than that of CO adsorption. The heats and entropies of CO adsorption on the Au sites indicated that the interaction between CO and Au supported on TiO2 is much stronger than that between CO and Au supported on ZnO. The Au/ZnO sample had the largest amount of lattice oxygen (7.6 μmol/g), which reacted with CO to give CO2. © 2009 American Chemical Society.

A strategy for the screening of the electrocatalytic activity of electrocatalysts for possible application in fuel cells and other devices is presented. In this approach, metal nanoclusters (Pt, Au, Ru, and Rh and their codeposits) were prepared using a capillary-based droplet-cell by pulsed electrodeposition in a diffusion-restricted viscous solution. A glassy carbon surface was modified with carbon nanotubes (CNTs) by electrophoretic accumulation and was used as substrate for metal nanoparticle deposition. The formed catalyst spots on the CNT-modified glassy carbon surface were investigated toward their catalytic activity for oxygen reduction as a test reaction employing the redox competition mode of scanning electrochemical microscopy (RC-SECM). Qualitative information on the electrocatalytic activity of the catalysts was obtained by varying the potential applied to the substrate; semiquantitative evaluation was based on the determination of the electrochemically deposited catalyst loading by means of the charge transferred during the metal nanoparticle deposition. Qualitatively, Au showed the highest electrocatalytic activity toward the oxygen reduction reaction (ORR) in phosphate buffer among all investigated single metal catalysts which was attributed to the much higher loading of Au achieved during electrodeposition. Coelectrodeposited Au-Pt catalysts showed a more positive onset potential (-150 mV in RC-SECM experiments) of the ORR in phosphate buffer at pH 6.7. After normalizing the SECM image by the charge during the metal nanocluster deposition which represents the mass loading of the catalyst, Ru showed a higher electrocatalytic activity toward the ORR than Au. © 2009 American Chemical Society.

Synthesis of shape- and size- controlled α-Fe2O3 nanoparticles was performed through a hydrothermal method assisted with amino acids. The products were characterized by transmission electron microscopy and X-ray diffraction. It was found that the type of amino acids has significant impact on the shape and size of the obtained α-Fe2O3 nanoparticles. The use of acidic amino acids typically leads to the formation of α-Fe2O3 nanoparticles with spindle shape. However, rhombohedrally shaped α-Fe2O3 nanoparticles were formed in the case of basic amino acids. When gold colloidal nanoparticles were deposited on the surfaces of α-Fe2O3 nanoparticles, Au/α-Fe2O3 catalysts display substantial differences in catalytic activities in CO oxidation for the differently shaped α-Fe2O3 nanoparticles used as supports. In general, spindle shaped Au/α-Fe2O3 shows higher catalytic activity than catalysts based on rhombohedral iron oxide. Under our catalytic test conditions, for spindle shaped Au/α-Fe2O3 catalyst, large hematite crystals induce higher catalytic activity than smaller ones, whereas for rhombohedral Au/α-Fe2O3 catalysts, medium-sized α-Fe2O3 nanocrystals show high catalytic activity for CO oxidation. © 2009 Elsevier B.V. All rights reserved.

The discovery and investigation of novel and efficient pathways for the conversion of biomass into fuels and chemicals are among the big challenges facing heterogeneous catalysis nowadays. However, not all experience gained in the transformation of hydrocarbons over the last 100 years can directly be transferred to biomass conversion. In this article, we will discuss how the specific properties of biomass pose new requirements on the processes and on the solids that are used as catalysts for their conversion. Due to the importance of lignocellulosic materials, which constitute ca. 95% of the total plant biomass, we will focus mostly on the desired properties of solid catalysts for the conversion of these polymeric biomolecules. Research in this field is very intense presently and novel transformations and catalysts are being discovered at a high rate. This paper thus focuses on the concepts that govern biomass transformation instead of giving a complete and comprehensive survey of the literature, which would be outdated within a short time. © The Royal Society of Chemistry 2009.

Again and again and again: The title reaction was achieved on a solid catalyst in a covalent triazine-based framework formed by trimerization of 2,6-dicyanopyridine in a ZnCl2 melt. The material possesses bipyridine units as coordination sites for platinum. It shows high activity and can be separated easily from the reaction mixture and recycled several times without significant loss of activity. © 2009 Wiley-VCH Verlag GmbH & Co. KGaA.

New ordered mesoporous carbide derived carbon materials with extraordinary high specific surface areas up to ∼2800 m2 g-1 were synthesized by selective extraction of silicon from ordered mesoporous silicon carbide. Although the degree of mesostructure ordering is lower than that of the CMK-type materials they exhibit higher specific surface areas and high protein adsorption capacities. We show that they can be effectively functionalized with sulfonic groups and become excellent solid acid catalysts for processing large organic molecules. © 2009 American Chemical Society.